| seq_num |
Sequence of message
|
|
| msg_id |
Type of Message
0 - Basic. Contains basic location information and signal quality;
1 - TLD. Contains Tramigo Landmark information;
4 - Trip. Contains information of a completed trip;
20 - Additional information like temperature and device I/O Extended states;
22 - Zone. Contains name of a zone and state if inside/outside of zone;
40 - Analog and OneWire. Values from Analog Input and OneWire accessories of device.
|
|
| report_trigger |
Report trigger code
|
|
| gsm |
GSM signal quality
|
-dBm |
| gps_antenna |
State of the GPS antenna. 0 = LNA off;
1 = Short circuit;
2 = Internal
3 = External
|
|
| distance |
Current odometer distance
|
m |
| pwr_int |
Voltage of the internal battery
|
mV |
| battery_charging |
Units: mV Status of the internal battery charger. 0 = Power disconnected;
1 = Charging;
2 = Battery full;
3 = Charging error
|
|
| state_flags |
Bit flags for the unit status.
0 - Charging. Bit0 is set if backup battery is being charged.
1 - Reserved
2 - Battery Low. Bit2 is set if backup battery is low.
3 - No Battery. Bit3 is set if no backup battery is installed in device;
4 - Bad Battery. Bit4 is set if bad backup battery is detected;
5 - Ignition On / Off. Bit5 is set if ignition is ON. Either I/O based or Shock Sensor;
6 - Reserved;
7 - Parked. Bit7 is set if device/vehicle is parked;
8 - Moving. Bit8 is set if device/vehicle is moving;
9 - Stopped. Bit9 is set if device/vehicle is stopped;
10 - Reserved.
|
|
| mcc |
Mobile Country Code of the current GSM operator
|
|
| mnc |
Mobile Network Code of the current GSM operator
|
|
| lac |
Location Area Code of the current serving GSM cell
|
|
| cell_id |
Cell ID of the current serving GSM cell |
|
| gsm_status |
Status of the GSM network registration 0 = No Network;
1 = Home network;
2 = Searching;
3 = Registration denied;
5 = Roaming network
|
|
| gsm_temp |
Temperature of the GSM module
|
C |
| speed_max |
Maximum speed since the previous report
|
km/h |
| speed_min |
Minimum speed since the previous report |
km/h |
| gps_signal |
Units: km/h GPS signal quality 0-100
|
% |
| gsm_signal |
GSM signal quality 0-100
|
% |
| tld_ref_id |
IF of the closest TLD location used as reference to previously indicated full TLD information Zero if TLD location is not available
|
|
| bearing_to_tld |
Bearing from the current location to the reference TLD location Units: degrees, 0=north, 90=east, etc.
|
|
| distance_to_tld |
Distance from the current location to the reference TLD location
|
m |
| battery_level |
Battery level 0-100. |
% |
| odometer |
The odometer of the current trip.
|
m |
| driver_id |
OneWire device ID of currently attached Driver ID fob.
|
|
| temp_# |
Temp Sensor # temperature
|
C |
| analog |
Voltage at the Analog Input of the device.
|
mV |
| city |
Name of city.
|
|
| district |
Name of larger area, like town or district.
|
|
| landmark |
Name of landmark.
|
|
| country_code |
Country where the landmark resides, 2 characters.
|
|
| start_bearing_to_tld |
Bearing in degrees to nearest Landmark at trip start location. |
degrees |
| start_distance_to_tld |
Distance in meters to nearest Landmark at trip start location. |
meters |
| end_bearing_to_tld |
Bearing in degrees to nearest Landmark at trip end location. |
degrees |
| end_distance_to_tld |
Distance in meters to nearest Landmark at trip end location. |
meters |
| trip_distance |
Traveled distance during trip in meters. |
meters |
| avg_speed |
Average speed during trip
|
km/h |
| max_speed |
Maximum speed recorded during trip
|
km/h |
| idle_time |
Amount of seconds device has been stationary during the trip. |
seconds |
