| event_code |
Event Code: 1 - SOS Pressed
2 - Input 2 Active 3 - Input 3 Active 4 - Input 4 Active 5 - Input 5 Active 9 - Input 1 Inactive 10 - Input 2 Inactive 11 - Input 3 Inactive 12 - Input 4 Inactive 13 - Input 5 Inactive 17 - Low Battery 18 - Low External Battery 19 - Speeding 20 - Enter Geo-fence 21 - Exit Geo-fence 22 - External Battery On 23 - External Battery Cut 24 - Lose GPS Signal 25 - GPS Signal Recovery 26 - Enter Sleep 27 - Exit Sleep 28 - GPS Antenna Cut 29 - Device Reboot 31 - Heartbeat 32 - Heading Change 33 - Distance Interval Tracking 34 - Reply Current (Passive) 35 - Time Interval Tracking 36 - Tow 37 - RFID 39 - Picture 40 - Power Off 41 - Stop Moving 42 - Start Moving 44 - GSM Jammed 50 - Temperature High 51 - Temperature Low 52 - Fuel Fulled 53 - Fuel Empty 54 - Fuel Stolen 56 - Armed 57 - Disarmed 58 - Stealing 63 - GSM No Jamming 65 - Press Input 1 (SOS) to Call 66 - Press Input 2 to Call 67 - Press Input 3 to Call 68 - Press Input 4 to Call 69 - Press Input 5 to Call 70 - Reject Incoming Call 71 - Get Location by Call 72 - Auto Answer Incoming Call 73 - Listen-in (Voice Monitoring) 78 - Impact 79 - Fall 80 - Install 81 - Drop Off 82 - Refuelling 83 - Ult-Sensor Drop 90 - Sharp Turn to Left 91 - Sharp Turn to Right 94 - Output 1 Active 95 - Output 2 Active 99 - Output 1 Inactive 100 - Output 2 Inactive 118 - Input 9 Active 119 - Input 9 Inactive 129 - Harsh Braking 130 - Harsh Acceleration 133 - Idle Overtime 134 - Idle Recovery 135 - Fatigue Driving 136 - Enough Rest after Fatigue Driving 138 - Speed Recovery 139 - Maintenance Notice 169 - BLE Alarm
|
(not set) |
| valid |
GPS status |
|
| gsm_signal |
GSM signal |
|
| hdop |
Horizontal Dilution of Precision |
|
| mileage |
Total accumulated mileage |
|
| engine_hours |
Total accumulated runtime |
|
| mcc |
Mobile Country Code |
|
| mnc |
Mobile Network Code |
|
| lac |
Location Area Code |
|
| cell_id |
Cell Tower ID |
|
| battery |
battery charge |
|
| pwr_ext |
Voltage of external power supply |
|
| gf_number |
Geo-fence number |
|
| inputs_status |
input port status. Indicates the status values of eight input ports. Bits 0–7 correspond to status of input ports 1–8.
|
(not set) |
| gps_valid |
GPS positioning status. 0x01: The GPS positioning is valid.
0x00: The GPS positioning is invalid.
|
(not set) |
| outputs_status |
Output port status. Indicates the status values of eight output ports. Bits 0–7 correspond to status of output ports 1–8.
|
(not set) |
| geo_fance_number |
Geo-fence number. The data is available only when the GPRS event code is 20 or 21.
|
(not set) |
| temp_sensor |
Temperature sensor No. Indicates temperature sensor 7. The data is available only when the GPRS event code is 50 or 51.
|
(not set) |
| taho_perf |
Tachograph performance. 01: performance analysis
00: normal performance
Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
(not set) |
| clutch_switch |
Clutch switch. 01: The clutch pedal is pressed.
00: The clutch pedal is released. Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
(not set) |
| park_brake |
Parking brake switch. 01: Apply the brake. 00: Do not apply the brake. Upload data after reading it. Only the CAN version supports this ID. Upload data after reading it.
|
(not set) |
| cruise_cnt |
Cruise control system. 01: The cruise control system is switched on.
00: The cruise control system is switched off.
Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
(not set) |
| acc_pedal |
Accelerator pedal position. Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
% |
| can_fuel_lvl |
CAN bus fuel level. Upload data after reading it. Only the CAN version supports this ID. Upload data after reading it.
|
% |
| act_eng_torque |
Actual engine torque. Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
% |
| act_eng_tor_speed |
Actual engine torque at current speed. Upload data after reading it.
Only the CAN version supports this ID. Upload data after reading it.
|
% |
| speed |
Speed
|
km/h |
| course |
Driving direction
|
°C |
| adc_# |
AD# Analog-to-digital converter
|
V |
| fuel_level_proc |
Fuel level (%)
|
% |
| veh_speed_taho |
Vehicle speed (based on the tachograph)
|
km/h |
| veh_speed_wheel |
Vehicle speed (based on the wheel)
|
km/h |
| engine_speed |
Engine speed
|
rpm |
| eng_cool_temp |
Engine coolant temperature
|
°C |
| amb_air_temp |
Ambient air temperature
|
°C |
| run_time |
Run time. Indicates the total time.
|
sec |
| system_flag |
System flag. The data is available only when the GPRS event code is 35. Bit 0: Whether to modify the EEP2 parameter. When the parameter value is 1, the EEP2 parameter is modified.
Bit 1: Indicates the ACC status. When the parameter value is 1, the ACC is on.
Bit 2: Indicates the anti-theft status. When the parameter value is 1, the tracker is in the arming state. Bit 3: vibration flag. When the parameter value is 1, the tracker is vibrating. Bit 4: moving flag. When the parameter value is 1, the tracker is moving. Bit 5: Whether to connect the external power supply. When the parameter value is 1, the external power supply is connected. Bit 6: Whether the tracker is charging. When the parameter value is 1, the tracker is charging. Bit 7: Whether to enable the sleep mode. When the parameter value is 1, the sleep mode is enabled. Bit 8: Whether to connect the FMS. When the parameter value is 1, the FMS is connected. Bit 9: Whether to enable the FMS function. When the parameter value is 1, the function is enabled. Bits 10–31: reserved.
|
(not set) |
| rfid |
RFID ID. Indicates the ID number of a RFID card.
|
(not set) |
| total_fuel_cons |
Total fuel consumption
|
L |
| total_eng_run_tm |
Total engine run time
|
hours |
| high_res_veh_dist |
High resolution vehicle distance
|
m |
| high_res_total_fuel_con |
High resolution total fuel consumption
|
L |
| fuel_cons_rate |
Fuel consumption rate
|
(L/H) |
| axle_weight |
Axle weight
|
kg |
| service_dist |
Service distance
|
km |
| fuel_cons |
Instantaneous fuel consumption.
|
km/L |
| rx_level |
rx level
|
(not set) |
| pic_name |
Picture name. The data is available only when the GPRS event code is 39.
|
(not set) |
| sens# |
Temperature sensor #
|
°C |
| netw_ver |
Network version
|
(not set) |
| netw_type |
Network type
|
(not set) |
| netw_descr |
Network descriptor
|
(not set) |
| ble_ver |
Version: indicates the data version.
|
(not set) |
| ble_type |
Type: indicates the alert type
|
(not set) |
| ble_dev_name |
Device name: indicates the device name.
|
(not set) |
| ble_mac |
indicates the MAC code of the device.
|
(not set) |
| ble_battery |
indicates the battery power of the device.
|
(not set) |
| ble_temp |
indicates the temperature of the device.
|
(not set) |
| ble_humi |
indicates the humidity of the device.
|
(not set) |
| ble_rssi |
indicates the signal strength.
|
(not set) |
| ble_a_ver |
Bluetooth beacon A. Version: indicates the data version.
|
(not set) |
| ble_a_dev_name |
Bluetooth beacon A. Device name: indicates the device name.
|
(not set) |
| ble_a_mac |
Bluetooth beacon A. Indicates the MAC code of the device.
|
(not set) |
| ble_a_battery |
Bluetooth beacon A. Iindicates the battery power of the device.
|
(not set) |
| ble_a_rssi |
Bluetooth beacon A. Indicates the signal strength.
|
(not set) |
| ble_b_ver |
Bluetooth beacon B. Version: indicates the data version.
|
(not set) |
| ble_b_dev_name |
Bluetooth beacon B. Device name: indicates the device name.
|
(not set) |
| ble_b_mac |
Bluetooth beacon B. Indicates the MAC code of the device.
|
(not set) |
| ble_b_battery |
Bluetooth beacon B. Iindicates the battery power of the device.
|
(not set) |
| ble_b_rssi |
Bluetooth beacon B. Indicates the signal strength.
|
(not set) |
| ble_temp_thres_high |
indicates the device temperature alert threshold.
|
(not set) |
| ble_temp_thres_low |
indicates the device temperature alert threshold.
|
(not set) |
| ble_humi_thres_high |
indicates the device humidity alert threshold
|
(not set) |
| ble_humi_thres_low |
indicates the device humidity alert threshold
|
(not set) |
| sens_ver |
Version: indicates the data version. |
(not set) |
| sens_temp |
indicates the temperature of the device
|
(not set) |
| sens_humi |
indicates the humidity of the device
|
(not set) |
| battery_#_status |
Battery status
|
(not set) |
| battery_#_level |
Battery level
|
% |
| battery_alert |
Battery alert
|
(not set) |
| battery_version |
Battery version |
(not set) |
