| flg |
additional parameters of the navigation package (EGTS_SR_POS_DATA)
|
|
| vdop |
Vertical dilution of precision (EGTS_SR_EXT_POS_DATA)
|
|
| hdop |
Horizontal dilution of precision (EGTS_SR_EXT_POS_DATA)
|
|
| pdop |
Position dilution of precision (EGTS_SR_EXT_POS_DATA)
|
|
| sat |
Satellites (EGTS_SR_EXT_POS_DATA)
|
|
| ns |
NS - bit flags characterizing the used navigation satellite systems. (EGTS_SR_EXT_POS_DATA) The following (decimal) flag values are defined:
0 - system not defined;
1 - GLONASS;
2 - GPS;
4 - Galileo;
8 - Compass;
16 - Beidou;
32 - DORIS;
64 - IRNSS;
128 - QZSS
|
|
| st |
Current operating mode. (EGTS_SR_STATE_DATA) List of modes:
0 "Passive"
1 "ERA"
2 "Active"
3 "Emergency call"
4 "Emergency Tracking"
5 "Testing"
6 "Car service"
7 "Download Software"
|
|
| pwr_ext |
MPSV
- The value of the voltage of the main power source (EGTS_SR_STATE_DATA)
|
0.1 V |
| pwr_int |
IBV - Internal battery voltage value (EGTS_SR_STATE_DATA)
|
0.1 V |
| bbv |
BBV - Backup battery voltage value (EGTS_SR_STATE_DATA)
|
0.1 V |
| acc_x |
XAAV - value of linear acceleration along the X axis (the most significant bit determines the sign, 1 indicates a negative value), in m/s2 with a resolution of 0.1 m/s2; (EGTS_SR_ACCEL_DATA)
|
m/s2 |
| acc_y |
YAAV - value of linear acceleration along the Y axis (the most significant bit determines the sign, 1 indicates a negative value), in m/s2 with a resolution of 0.1 m/s2; (EGTS_SR_ACCEL_DATA)
|
m/s2 |
| acc_z |
ZAAV - value of linear acceleration along the Z axis (the most significant bit determines the sign, 1 indicates a negative value), in m/s2 with a resolution of 0.1 m/s2; (EGTS_SR_ACCEL_DATA)
|
m/s2 |
| inputs |
Inputs (EGTS_SR_ABS_DIG_SENS_DATA)
|
|
| dsn#_state |
Digital Sensor State. (EGTS_SR_ABS_DIG_SENS_DATA) # is Digital Sensor Number
|
|
| adc# |
Analog Sensor Value (EGTS_SR_ABS_AN_SENS_DATA) |
|
| counter# |
CNV - the value of the readings of the counting input. (EGTS_SR_ABS_CNTR_DATA) # is "CN" - counting input number;
|
|
| lin#_state |
LIS - loop input state value. (EGTS_SR_ABS_LOOPIN_DATA)
# - loop input number;
|
|
| lls_err_flag |
LLSEF - Liquid Level Sensor Error Flag
(EGTS_SR_LIQUID_LEVEL_SENSOR)
|
|
| lls_format |
RDF - (Raw Data Flag) flag that determines the format of the LLSD field (EGTS_SR_LIQUID_LEVEL_SENSOR)
|
|
| lls_unit |
LLSVU - (Liquid Level Sensor Value Unit) bit flag that determines the units of measure for readings (EGTS_SR_LIQUID_LEVEL_SENSOR)
0 - Uncalibrated LLS reading.
1 - LLS readings as a percentage of the total tank volume;
2 - LLS readings in liters with a resolution of 0.1 liters.
|
|
| module_addr |
MADDR - address of the module from which data on LLS readings were received by the subscriber terminal (number of external port of subscriber terminal) (EGTS_SR_LIQUID_LEVEL_SENSOR)
|
|
| lls# |
LLSD (Liquid Level Sensor Data) (EGTS_SR_LIQUID_LEVEL_SENSOR) # is LLSN - (Liquid Level Sensor Number) sensor serial number;
|
|
| dpr |
DPR - (Doors Presented) a bit field that determines the presence of counters on the doors and the structure of the PCD field (bit 0 determines the presence of a counter on the 1st door, bit 1 on the 2nd, etc.). If the bit has a value of 1, then the counter is used; if 0, it is not used; (EGTS_SR_PASSENGERS_COUNTERS) |
|
| drl |
DRL - (Doors Released) a bit field that defines the doors that opened and closed when counting passengers (for example, 00000000 - none of the doors opened, 00000001 - only the 1st door opened, 00001001 - the 1st and 4th doors opened a door); (EGTS_SR_PASSENGERS_COUNTERS)
|
|
| madr |
MADDR is the address of the module from which data from the passenger flow counters were received by the subscriber terminal (number of the external port of the subscriber terminal); (EGTS_SR_PASSENGERS_COUNTERS)
|
|
| ipq_# |
IPQ1...IPQ8 - number of entered passengers through 1 ... 8 doors; (EGTS_SR_PASSENGERS_COUNTERS)
|
|
| opq_# |
OPQ1...OPQ8 - the number of exiting passengers through 1 ... 8 doors; The presence or absence of the IPQ and OPQ fields is determined by the bits of the DPR field of the EGTS_SR_PASSENGERS_COUNTERS subrecord. If the bit corresponding to a particular door number in the DPR field has the value 1, then the corresponding IPQ and OPQ fields are present in the structure. If a bit in the DPR field has the value 0, then the corresponding IPQ and OPQ fields are not present in the structure. If a particular IPQ field is present, then the corresponding OPQ field is also present. (EGTS_SR_PASSENGERS_COUNTERS)
|
|
| cb_moto |
Engine hours read (EGTS_SR_CAN_DATA)
|
hours |
| cb_odometr |
Mileage read (EGTS_SR_CAN_DATA)
|
km |
| cb_speed |
Vehicle speed (EGTS_SR_CAN_DATA)
|
km/h |
| cb_odom_to |
Mileage before maintenance (EGTS_SR_CAN_DATA)
|
km |
| cb_fuel_consumption |
Total fuel consumption read (EGTS_SR_CAN_DATA)
|
liter |
| cb_fuel_level |
Fuel level in the tank read (EGTS_SR_CAN_DATA)
|
% |
| cb_fuel_volume |
Fuel level in the tank read (EGTS_SR_CAN_DATA)
|
liter |
| cb_liquid_level |
AdBLUE liquid level (EGTS_SR_CAN_DATA)
|
% |
| cb_liquid_volume |
AdBLUE liquid level (EGTS_SR_CAN_DATA)
|
liter |
| cb_temp_coolant |
Coolant temperature (engine temperature -40 to 210 °C) (EGTS_SR_CAN_DATA)
|
°C |
| cb_engine_rpm |
Engine rpm (EGTS_SR_CAN_DATA)
|
rpm |
| cb_gas_pedal |
Accelerator position 0 to 100% (EGTS_SR_CAN_DATA)
|
% |
| cb_load_engine |
Engine load 0 to 125% (EGTS_SR_CAN_DATA)
|
% |
| cb_axis_weight_# |
Axle load (EGTS_SR_CAN_DATA) # is an axle number
|
kg |
| cb_guard_alarm |
Crash controllers (EGTS_SR_CAN_DATA):
0 side lights
1 low beam
2 high beam
3 Driver's belt
4 Passenger belt
5 STOP
6 Oil pressure / oil level
7 Temp. cooling Jew. dvig.
8 Brake system
9 Charging the battery
10 Safety system (SRS)
11 Check the engine
12 Outdoor lighting
13 Tire pressure
14 Brake pad wear
15 Warning
16 ABS
17 Low fuel level
18ESP
19 Glow plug
20 FAPs
21 EPCs
|
|
| cb_accident |
Security/guard parameters (EGTS_SR_CAN_DATA):
0 ignition on
1 key is in the ignition
2 dynamic ignition on 2
3 the engine is running (information is available only when the ignition is on)
4 standard alarm is in alarm mode
5 driver's door open
6 passenger door open
7 trunk open
8 open hood
9 the handbrake lever is tightened (information is available only when the ignition is on)
10 foot brake applied (information is only available when the ignition is on)
11 Webasto enabled
12 the car is locked with the standard key fob
13 the car is opened using the standard key fob
14 the trunk is opened using the standard key fob
15 the module sent an arming/disarming signal to the alarm
|
|
| cb_machinery |
Condition of agricultural machinery (EGTS_SR_CAN_DATA): 0 ignition on
1 Handbrake applied (information available only when the ignition is on)
2 Low fuel level
3 high beam
4 Turning on the header
5 Ejection of grain from the bunker
|
|
| cb_bk_vulkan |
Parameters from the on-board computer "VulKan" (EGTS_SR_CAN_DATA):
0 Discarded concave state
1 grain tank entrance open
2 grain hopper 100%
3 grain hopper 70%
4 the drain filter of the hydraulic system of the power cylinders is clogged
5 the pressure filter of the hydraulic system of the power cylinders is clogged
6 oil level in the oil tank
7 the pressure filter of the brake hydraulic system is clogged
8 oil filter clogged
9 fuel filter clogged
10 presence of water in fuel
11 clogged air filter
12 engine oil temperature
13 emergency oil temperature in the hydraulic system of power cylinders
14 emergency oil pressure in the engine
15 emergency engine coolant level
16 overflow section of the hydroblock
17 the drive of the unloading auger is switched on with the unloading pipe folded
18 no operator
19 clogged straw walker
20 cleaning fan control off
21 disable threshing drum control
|
|
| cb_reaper_hours |
harvest time (EGTS_SR_CAN_DATA)
|
|
| cb_harvested_area |
Harvested area (EGTS_SR_CAN_DATA)
|
|
| cb_productivity |
Performance (EGTS_SR_CAN_DATA)
|
|
| cb_harvest_amount |
Harvested quantity (EGTS_SR_CAN_DATA) |
tons |
| cb_grain_moisture |
Grain moisture content (EGTS_SR_CAN_DATA)
|
% |
| cb_threshing_drum_rpm |
Threshing drum rpm (EGTS_SR_CAN_DATA)
|
rpm |
| cb_out_concave_clrnc |
Outlet concave clearance (EGTS_SR_CAN_DATA)
|
|
| ida |
IDA (Identity Device Address) – reader network address or reader number specified by the block. (EGTS_SR_IDENTITY_DATA)
|
|
| icn |
ICN (Identity Card Number) – the value of the serial number of the card, the length is determined by the length of the serial number, the upper unused bits are filled with zeros. (EGTS_SR_IDENTITY_DATA)
|
|
| avl_driver_id |
ICN (Identity Card Number) – the value of the serial number of the card, the length is determined by the length of the serial number, the upper unused bits are filled with zeros. (EGTS_SR_IDENTITY_DATA)
|
|
| temp_# |
TS1…N (Temperature Sensor) – Value from temperature sensors in degrees Celsius. (EGTS_SR_TRMO_DATA)
|
°C |
| refr_type |
REFR_TYPE (Refrigerator Model) – refrigerator model (type). The refrigerator model is selected when configuring the terminal (locally or remotely). (EGTS_SR_THERMO_DATA)
TKDL-PRO - 0
TouchPrint - 1
DataCold - 2
TKDL-SPR - 3
ThermoKing SLX (via IQFREEZE) - 4
Carrier STD32 (via IQFREEZE) - 5
Zanotti (via IQFREEZE) - 6
Thermal Master (via IQFREEZE) - 7
Carrier NDP33LN6FB (via IQFREEZE) - 8
|
|
| route_num |
Route number. Example:
Route k315ab
k - route prefix
315 - number
a - first letter
b - second letter
|
|
| direction |
Direction of moving:
0: No;
1: Forward;
2: Returning.
|
|
