| min_speed |
Minimum speed in km/h that must be achieved before reporting next position. |
|
| axel_weight_3 |
Represents the weight on the third axle of a vehicle. |
|
| kickdown_switch |
A switch that activates an automatic transmission's kickdown feature, allowing for rapid acceleration. |
|
| parking_brake |
Parking Brake Switch Status |
|
| on_duration |
Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted. |
|
| num_clutch_presses |
Indicates the number of times the clutch pedal has been pressed. |
|
| trip_distance |
The total distance traveled during a specific trip. |
|
| oil_pressure |
Measures the pressure of the oil in the engine, which is important for engine health. |
|
| cango_abs_warn_lamp |
Warning lamp indicating the status of the anti-lock braking system (ABS). |
|
| humidity_# |
The percentage of water vapor present in the air. |
|
| tpms_press_# |
The pressure reading from a tire pressure monitoring system. |
|
| axle4 |
The fourth axle of a vehicle, which is part of the vehicle's suspension and drivetrain. |
|
| accel_y |
The acceleration in the Y-axis direction, indicating movement |
|
| fuel_cons |
Fuel Consumption |
|
| min_heading |
Minimum heading in degree that must be changed before reporting next position. (15..180) |
|
| eng_load |
OBD Calculated engine load |
|
| actual_speed |
The real-time speed at which a vehicle is traveling. |
|
| mnc |
Current MNC |
|
| accel_pos |
Accelerator pedal |
|
| dur_engine_torque |
The amount of torque produced by an engine over a period of time. |
|
| intake_manifold_air_temp |
Engine Intake Manifold 1 Temperature |
|
| maf_air_rate |
OBD MAF air flow rate |
|
| intake_manifold_temp |
Engine Intake Manifold 1 Temperature |
|
| fms1_fuel_level |
The level of fuel in the fuel management system. |
|
| tachograph_status |
Tachograph Overspeed status |
|
| abs_time |
Time ABS Active |
|
| rtc_tm |
RTC Time. Unix Timestamp |
|
| fuel_used_dur_idle |
The amount of fuel consumed while the vehicle is idling. |
|
| driver2_card |
Information related to the second driver's card. |
|
| eng_hours |
The total hours the engine has been operational. |
|
| axel_weight_2 |
The weight on the second axle of the vehicle. |
|
| ble_mac_TD_# |
The MAC (Media Access Control) address for a Bluetooth Low Energy (BLE) device. |
|
| ble_rssi_# |
The Received Signal Strength Indicator (RSSI) for a Bluetooth Low Energy (BLE) device. |
|
| status |
Current status of RPM over-revving event
0: RPM (Engine over-revving) OFF
1: RPM (Engine over-revving) ON
|
|
| snd_tm |
Position Sending Time. Unix Timestamp |
|
| pt_air_pressure |
Parking and/or Trailer Air Pressure |
|
| sensor_id |
Temperature sensor ID. This temperature sensor can be set to be index 1 or 2 by specifying the ID in this field. |
|
| cruise_active |
Indicates whether the cruise control system is active. |
|
| trip_end_tm |
The time when a trip ends. |
|
| gl |
Google Link (N/A in AX5) |
|
| cargo_weight |
Cargo Weight |
|
| gps_status |
Indicates the current status of the GPS system. |
|
| coolant_temp |
Engine Coolant Temperature |
|
| vehicle_id |
A unique identifier for the vehicle. |
|
| coll_num |
Number of position to be put into one TCP/UDP packet |
|
| eh_01 |
Engine hour in 0.1 hour |
|
| idle_duration |
The amount of time a vehicle remains stationary with the engine running. |
|
| trip_start_lat |
The latitude coordinate indicating where the trip began. |
|
| dest_type |
Specify the destination for tracking report position The parameter is in conjunction with the following bits:
0: Default communication type. (i.e. Command issuer)
Bit 0: SMS
Bit 1: GPRS (This is the only option for AY5)
Bit 2: USSD
Bit 3: Serial
|
|
| temp1 |
First Temperature Sensor Value |
|
| drivers_state |
Driver1/2 Working State |
|
| odometer |
Odometer |
|
| veh_status |
The current status of the vehicle. |
|
| driver1_card |
Represents the IC card status of the driver's professional qualification certificate. |
|
| obd_speed |
Speed of the vehicle as determined by the On-Board Diagnostics (OBD) system. |
|
| vin |
VIN number |
|
| ble_mac_# |
The unique identifier for a Bluetooth device, often used for wireless communication. |
|
| eng_starter |
Represents the status of the engine's starter system. |
|
| brake_times |
Brake Switch apply times |
|
| pto_active |
Indicates whether the Power Take-Off (PTO) is currently active or not. |
|
| temp_data_# |
Represents temperature data, where '#' could refer to different temperature sensors or readings. |
|
| num_brake_app_th |
The number of times the brake has been applied. |
|
| mag_data_# |
Represents magnetic data, where '#' could refer to different magnetic sensors |
|
| IMEI |
International Mobile Equipment Identity, a unique identifier for the device. |
|
| curr_a_temp |
The temperature reading from sensor ID A |
|
| turbo_pressure |
Indicates the pressure level within the turbocharger system. |
|
| trip_start_tm |
The start time of a trip. |
|
| output_status |
Represents the current status of the output. |
|
| cruise_time |
Time Cruise active |
|
| pwr_int |
Power supply internal battery |
|
| fuel_consumption |
Fuel Used in 0.1 liter |
|
| temp_b_id |
The sensor ID corresponding to temperature B |
|
| service_dist |
Indicates the distance remaining or covered in relation to vehicle maintenance or service. |
|
| ble_temp_TD_# |
Refers to temperature data associated with a Bluetooth device. |
|
| rpm_on_tresh |
RPM for detecting RPM (Engine over-revving) ON state. |
|
| min_temp |
Minimum temperature value, and is in 0.1 |
|
| brake_app_pressure |
Brake Application Pressure |
|
| clutch_times |
Clutch Switch apply times |
|
| current_rpm |
Current RPM reading |
|
| IMSI |
International Mobile Subscriber Identity, a unique number associated with all cellular networks, used to identify the user of a cellular network. |
|
| pulse_count |
Pulse count value |
|
| engine_rpm |
Engine RPM reading |
|
| sched |
Specify the schedule for the report. The parameter is in conjunction with the following bits:
0 – indicates use no schedule (i.e. always on)
Bit 0 – Schedule 1
Bit 1 – Schedule 2
Bit 2 – Schedule 3
Bit 3 – Schedule 4
Bit 4 – Schedule 5
Bit 5 – Schedule 6
Bit 6 – Schedule 7
Bit 7 – Schedule 8
|
|
| tpms_id_# |
Identifier for the Tire Pressure Monitoring System. |
|
| firmware_ver |
Version of the firmware installed on the device. |
|
| report_id |
Report ID |
|
| trottle_pos |
Throttle Position |
|
| cango_seat_belt |
Status indicating whether the seat belt is fastened. |
|
| accel_pedal_pos |
Position of the accelerator pedal, indicating how much it is pressed. |
|
| clutch_switch |
Status indicating whether the clutch is engaged or disengaged. |
|
| sats |
Number of satellites involved in positioning |
|
| mil_on_status |
OBD MIL ON (Engine Fault) Status |
|
| prf |
Message prefix |
|
| fuel_# |
This parameter refers to the fuel-related data |
|
| cango_amb_warn_lamp |
This parameter refers to the status of the ambient warning lamp. |
|
| fms1_odometer |
This parameter refers to the vehicle's odometer reading. |
|
| vss_value |
VSS value is total pulses for 1 kilometer. |
|
| fuel_level |
Fuel Level |
|
| eng_boost_pressure |
Engine Turbocharger Boost Pressure |
|
| temp2 |
Second Temperature Sensor Value |
|
| brake_pressure1 |
Brake Primary Pressure |
|
| trootle_pos |
OBD Throttle position |
|
| mcc |
Current MCC |
|
| axel_weight_1 |
The weight measurement of the first axle. |
|
| fuel_pressure |
The pressure at which fuel is delivered to the engine. |
|
| model_name |
The name of the model for a specific device |
|
| ble_name_TD_# |
The name of the Bluetooth device. |
|
| engine_tmp |
The temperature of the engine. |
|
| brake_pressure2 |
Brake Secondary Pressure |
|
| cango_collant_tmp_fm |
The temperature of the engine coolant. |
|
| idling_time |
The duration for which an engine runs without moving the vehicle. |
|
| min_send_dist |
Minimum distance in multiple of 10 meters that must be traveled before reporting next position. (Min. 20 meters) |
|
| acc_off_time |
Minimum time in seconds that must elapse before reporting next position while the ACC is in Off status.
ACC status in Mode must be set in order to use this time interval. (Min. 1 seconds) |
|
| total_fuel |
The total amount of fuel consumed. |
|
| total_hours |
The cumulative number of hours of operation |
|
| trip_start_long |
The longitude coordinate indicating where a trip started. |
|
| total_dist |
The total distance traveled. |
|
| dur_driving |
Duration of driving |
|
| tachograph_speed |
Speed recorded by the tachograph |
|
| accel_x |
Acceleration in the X direction |
|
| ble_battery_voltage_TD_# |
Battery voltage related to Bluetooth communication. |
|
| abs_active |
Indicates whether the anti-lock braking system (ABS) is active. |
|
| temp_a_id |
The sensor ID corresponding to temperature A |
|
| tracking_mode |
The GPS tracking Mode parameter can be in conjunction with the following bits:
Bit 0: Time mode
Bit 1: Distance mode
Bit 2: ACC status (Must combine with Bit 0 or Bit 1)
Bit 3: Heading change condition
Bit 4: Minimum speed (Must combine with Bit 0 or Bit 1)
Bit 5: Engine status = ON. (Must combine with Bit 0 or Bit 1)
Bit 6: Motion status = ON. (Must combine with Bit 0 or Bit 1)
Bit 7: Logical Operation Mode (0=AND; 1=OR; Default=0) This mode only works when combining Time, Distance, and/or Heading change.
Bit 8: Reset tracking timer when event report is sent
Bit 9: Report with unique ID when in Distance Mode (Must combine with Bit 1)
|
|
| axle3 |
Refers to the third axle of a vehicle. |
|
| j1939_fuel_level |
Fuel level measurement according to the J1939 standard. |
|
| curr_b_temp |
The temperature reading from sensor ID B |
|
| rpm_value |
RPM value for each pulse. |
|
| gn |
10Hz G sensor data |
|
| fms12_tr2_abs_faults |
Faults related to the ABS system in FMS (Fleet Management System) data for the second trailer. |
|
| max_temp |
Maximum temperature value, and is in 0.1 |
|
| off_duration |
Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted. |
|
| intake_air_temp |
OBD Intake air temperature |
|
| gsm_level |
The strength of the GSM signal, indicating the quality of mobile network reception. |
|
| tacho_ext_info |
Direction, Tachograph performance, handling info, system event |
|
| trip_idle_tm |
Total idle time in one trip measured in seconds. |
|
| track_times |
Specify tracking times. =0 means forever tracking.
|
|
| accel_z |
The acceleration measurement along the Z-axis used in vehicle dynamics. |
|
| fms3_odometer |
Distance traveled by the vehicle, measured in kilometers. |
|
| total_eng_hours |
Total engine hours |
|
| sensor_index |
The connected port number where the Temperature Sensor connected with by different user.
1: First detected sensor
2: Second detected sensor
|
|
| hdop_filter |
Indicates whether the GPS signal is filtered to prevent drifting based on the Horizontal Dilution of Precision (HDOP). |
|
| gsm_status |
GSM status |
|
| engine_hours |
Engine hours |
|
| dur_accel |
Duration of acceleration |
|
| hold_duration |
A temperature holding time, and is in minute unit. |
|
| pwr_ext |
Voltage of external power supply |
|
| min_send_time |
Minimum time in seconds that must elapse before reporting next position. (Min. 1 seconds) |
|
| rfid_id_# |
A unique identifier associated with an RFID (Radio Frequency Identification) tag, used for tracking purposes |
|
| tpms_temp_# |
The temperature reading from the Tire Pressure Monitoring System. |
|
| rpm_off_tresh |
RPM for detecting RPM (Engine over-revving) OFF state. |
|
| trip_total_tm |
Total time taken for a trip, calculated as the difference between the trip's end time and start time. |
|
| ble_temp_# |
Temperature reading from a Bluetooth sensor |
|
| gps_tm |
GPS Time. Unix Timestamp |
|
| num_brake_app |
Number of times the brakes have been applied |
|
