| reason_text |
A textual reason why the event was generated |
|
| reason_code |
A numeric reason why the event was generated |
|
| ign |
0 or 1 signifying the ignition state |
|
| duration |
Context based duration value(e.g Idling event has been reporting for 'reported duration') |
seconds |
| roll_time |
Total time equipment has been in motion |
seconds |
| true_odometer_km |
Actual vehicle odometer, else empty |
kilometers |
| true_odometer_miles |
Actual vehicle odometer, else empty |
miles |
| odometer_km |
Odometer in Kilometers |
kilometers |
| odometer_miles |
Odometer in Miles |
miles |
| phone_number |
Phone number of modem if available |
|
| accelpoints |
Instantaneous X/Y/Z accelerometer data |
|
| location_trail |
Trails provide a high-resolution travel path for vehicles, allowing for bread crumb trails of vehicle location & speed |
|
| iostates |
Bitfield to reflect actual state of IO. Bitwise-AND the data to determine individual state. 0x100 for Ignition wire, 0x200 for panic button input |
|
| ble_client_state |
Bluetooth connected state. 1=connected, 0=disconnected, empty = unknown |
|
| sats_in_view |
Number of satellites in view |
|
| ign_duration |
Cumulative seconds Ignition was on |
seconds |
| pwr_ext |
Battery voltage measured in mv measured by device |
volts |
| pwr_int |
Battery voltage measured in mv of the internal battery in Device |
volts |
| total_idle_dur |
Total Duration of time that the vehicle has been in idling state |
seconds |
| fence_id |
Shows active fence ID |
|
| harness_detection |
Harness detection status |
|
| odometer_change_km |
Change in odometer since last packet construction (in km). ECU if gps_odometer is overwrite by ECU odometer |
kilometers |
| odometer_change_miles |
Change in odometer since last packet construction (in miles). ECU if gps_odometer is overwrite by ECU odometer |
miles |
| cell_information |
Cellular Information |
|
| format_checksum |
16 bit CCITT Checksum of packet format string (Useful to switch server parser based on packet contents) |
|
| firmware_ver |
16 bit CCITT Checksum of App Firmware version string:Supervisor FW Version:Bluetooth FW Version (Bluetooth FW Version only present on devices that support Bluetooth) |
|
| cell_rssi |
Current Cell RSSI value |
dBm |
| cluster_data |
Location Cluster Data |
|
| engine_rpm |
Instantaneous engine RPM |
RPM |
| engine_coolant_temp |
Instantaneous engine coolant temperature |
°C |
| engine_speed |
Instantaneous speed reported by ECU in MPH |
RPM |
| engine_odometer |
Odometer reported by ECU in miles |
kilometers |
| vin |
VIN number reported by ECU. Can also be set by using SETVIN command |
|
| fuel_level |
Fuel level reported by ECU (1-100%) |
% |
| dtc |
Active Diagnostic Trouble Codes reported by ECU |
|
| throttle_position |
Throttle Position reported by ECU |
% |
| obd_pwr_ext |
Battery Voltage reported by ECU |
volts |
| ambient_temperature |
Ambient Temperature reported by ECU |
°C |
| cumulative_fuel_economy |
Cumulative Fuel Economy calculated for vehicle, in hundredths of miles per gallon |
mpg |
| trip_fuel_economy |
Fuel Economy calculated for current trip, in hundredths of miles per gallon |
mpg |
| current_fuel_economy |
Instantaneous Fuel Economy calculated, in hundredths of miles per gallon |
mpg |
| ecu_all_dtc |
All Diagnostic Trouble Codes reported by ECU |
|
| dpfregen_inhibit |
0=Not inhibited, 01=Inhibited |
|
| j1939_engine_hours |
In 1/100th hour increments, eg, 76168 is 761.68 Hours |
hours |
| j1939_total_fuel_used |
Total fuel used for petrol or diesel engines. Captured from ECU for J1939/J1708(Lifetime); calculated for OBD-II.(Tracker Tenure) |
liters |
| j1939_total_gas_used |
Total gas used for gaseous engines (e.g., natural gas) |
liters |
| j1939_idle_hours |
In 1/100th hour increments e.g 27155 = 271.55 Hours |
hours |
| total_pto_hours |
In 1/100th hour increments, eg, seconds / 36 |
hours |
| max_vehicle_speed_limit |
Speed limit set in ECU |
km/h |
| j1939_oil_temperature |
In hundredths of degrees Celsius |
°C |
| j1939_engine_oil_level |
Oil level reported by ECU. e.g 1000/10= 100% |
% |
| j1939_coolant_level |
Coolant level reported by ECU. e.g 1000/10= 100% |
% |
| j1939_diesel_exhaust_fluid_level |
DEF level reported by ECU e.g 712 = 71.2 % |
% |
| j1939_diesel_exhaust_fluid_temperature |
DEF temperature reported by ECU |
°C |
| dpf_soot_load |
Soot DPF Buildup reported by ECU (0-250%) with 100% triggering active regeneration, and 0%, 25%, 50%, and 75% representing varying soot levels before regeneration is needed |
% |
| dpf_time_since_last_active_regeneration |
Value can be between 0-421,108,1215 seconds |
hours |
| dpf_soot_load_regeneration_threshold |
0-160.6375 % e.g 555300 = 55.53% |
% |
| dpf_status |
000 = Regeneration not needed, 001 = Regeneration needed - lowest level, 010 = Regeneration needed - moderate level, 011 = Regeneration needed - highest level, 7= Not available |
|
| dpf_active_regeneration_status |
00=not active,01=active,10=regeneration needed(Automatically initiated active regeneration imminent),11=not available |
|
| transmission_oil_level |
Oil level reported by ECU |
% |
| transmission_oil_temperature |
Oil temperature reported by ECU ( Range: -273 to 1735 ) e.g 6346 = 63.46 Celcius |
°C |
| transmission_current_gear |
Values from -125 to +125 represent gears: negative for reverse, positive for forward, zero for neutral, and 126 for park |
|
| seatbelt_switch |
State of switch used to determine if Seat Belt is buckled. (0) NOT Buckled. (1) OK - Seat Belt is buckled. (2) Error - Switch state cannot be determined. (3) & (255) Not Available |
|
| ecu_odometer_km |
Odometer reported by ECU in kilometers |
kilometers |
| ecu_speed_km |
Instantaneous speed reported by ECU in KPH |
km/h |
| j1939_cruise_control_state_time |
Total time cruise control is engaged in seconds. Reset after each use in packet |
seconds |
| j1939_cruise_control_state |
1=Hold,2=Accelerate,3=Decelerate,4=Resume,5=Set,6=Override |
|
| dm1 |
Diagnostic Trouble Codes reported by ECU for J1939 Protocol |
|
| dm2 |
Diagnostic Trouble Codes reported by ECU for J1939 Protocol |
|
| ecu_idle_fuel_used |
Fuel used while idling for petrol or diesel engines. Captured from ECU for J1939/J1708; calculated for OBD-II.(Tracker Tenure) |
liters |
| ecu_trip_fuel_used |
Trip fuel used for petrol or diesel engines. Captured from ECU for J1939/J1708; calculated for OBD-II |
liters |
| j1939_trip_gas_used |
Trip gas used for gaseous engines (e.g., natural gas) |
liters |
| tpms_all_tires |
Add all tires information to the packet |
|
| tpms_fault_tires |
Add only faulty tires information to the packet |
|
| ecu_pto_state |
PTO Governor State. 0=off, 1 through 19 engaged. Can also be hardwired to generate PTO State |
|
| ecu_chargelvl |
Electric vehicle Charge level |
% |
| one_w_sensor_serial_num |
Serial number of One-wire temperature sensor (79 series only) |
|
| one_w_sensor_temp |
Tenth of a Degree Celsius (79 series only) |
°C |
| driver_id |
1-wire DRIVER ID tag information or BLE Driver ID tag information. Multiple tags are separated by the space character |
|
| tool_tag |
Tool Tracking Tag information. Multiple tags are separated by the space character |
|
