| input_status |
These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 =
Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open.
|
|
| msg_sub_type |
Message sub-type code.
Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Loction Area alert message. Value is 3 in the Input Status Changed message. Value is 4 in the Undesired Input State message. Value is 5 in the Re-Centering message. Value is 6 in the Speed & Heading message
|
|
| vibr |
Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
|
|
| gps_fix_2d |
Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
|
|
| motion |
Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At-Rest when the message was transmitted.
|
|
| num_tries |
Number of Transmissions (1 to 15 Transmissions)
|
|
| min_trans_interval |
Minimum Interval between transmission attempts ( 5 second resolution) Default is 300 seconds
|
|
| max_trans_interval |
Maximum Interval between transmission attempts, Default is 600 seconds
|
|
| gps_mean_search_time |
Unsigned binary count in seconds for mean GPS search to acquire
|
|
| gps_fails |
Unsigned binary count of failed GPS attempts since last Diagnostic message
|
|
| alarm |
Alarm Statistics |
|
| alarm1_count |
Alarm2 since last message (b7=0) / accum hours (b7=1) |
|
| alarm2_count |
Alarm3 since last message (b7=0) / accum hours (b7=1)
|
|
| transmissions |
Transmissions since last statistics message |
|
| input№_undesired_state_time |
Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
|
|
| vibration_time |
Accumulated time that the SMARTONE has been in a State of Vibration with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
|
|
| input№_switches_number |
The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)
|
|
| transms_num |
Number of transmissions per burst.
|
|
| bat |
Battery Condition. 0 = Good battery. 1 = Replace Battery
|
|
| gps |
GPS Subsystem Fault. 0 = GPS system OK. 1 = Fault.
|
|
| transmt |
Transmitter Subsystem Fault. 0 = Transmitter OK. 1 = Fault.
|
|
| sched |
Scheduler Subsystem Fault. 0 = OK. 1 = Fault.
|
|
| msg_type |
0 Standard Message Type
3 Non Standard message type
|
|
| vibr_trigger |
Value 1 = This message is being sent because Transmit on Change of Vibration State is selected and the vibration just changed state, or Undesired Vibration State is selected and the vibration is in the undesired state. Value 0 = This message is being transmitted for a reason other than the above reasons.
|
|
| input_state |
These bits reflect the state of the Inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 = Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open
|
|
| input1_undesired_state_time |
Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
|
|
| input1_switches_number |
The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)
|
|
| input2_undesired_state_time |
Accumulated time that Input 2 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 2 Accumulate has been turned off)
|
|
| input2_switches_number |
The total number of openings or closings of input 2 as selected by the user. (OxFF means that Input 2 Accumulate has been turned off)
|
|
