Localizador GPS Globalstar SmartOne

Características Globalstar SmartOne:

Caja negra
Terminal satelital

Soportado en Wialon:

Sensores Digitales
Comunicación vía TCP

Para que el sistema de rastreo Wialon identifique los datos de Globalstar SmartOne en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo:	Globalstar SmartOne
ID único:	serial

Indique los siguientes parámetros en el programa de configuración o en la configuración Globalstar SmartOne para utilizarlos en Wialon Hosting :

Puerto del servidor:

20335

En el centro de servicio Wialon se utilizan 1829 unidades Globalstar SmartOne — es 0.08% de la cantidad total de dispositivos Automóvil conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro	Descripción	Unidades de medida
alarm	These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 = Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message. Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message.
input_state	Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message. Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message. (this parameter has the same information as the second half of the alarm)
vibr	Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
gps_fix_2d	Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
motion	Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At- Rest when the message was transmitted.
inputs	Bit (2) 0 = Good battery. 1 = replace battery. Bit (3) 0 = GPS Data valid in this message. 1 = GPS failed in this message cycle, ignore Latitude and Longitude fields. Bit (4) Missed Input 1. A value of 1 in this bit means that an input state change of input 1 was missed due to the transmission of a higher priority message. Bit (5) = Missed Input 2. A value of 1 in this bit means that an input state change of Input 2 was misse Bit (7:6) = GPS fail counter. Counts up to a maximum value of 3 upon GPS failure.

Globalstar SmartOne uses the Globalstar satellite network which provides coverage over most traveled areas of the planet

To get data from terminals please use HTTP protocol and this server address:

Wialon Hosting	Wialon Kit
http://193.193.165.165:20335/	http://193.193.165.169:20335/

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Products

Soluciones de nicho para satisfacer las tareas específicas

Globalstar SmartOne

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Hacerse socio

Solicite Wialon en su región

Por favor, llene la solicitud para iniciar el trabajo con Wialon