Globalstar SmartOne

Globalstar SmartOne
Fabricant: Globalstar
Forum de discussion

Nombre des unités

206
En ligne
1864
Nombre total
Caractéristiques Globalstar SmartOne:
  • Boîte à mémoire
  • Terminal satellite
Compatible avec Wialon:
  • Capteurs numériques
  • Communication via TCP

Afin d'identifier le boîtier Globalstar SmartOne les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Globalstar SmartOne
ID unique: serial

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Globalstar SmartOne pour les utiliser dans Wialon Hosting :

Port du serveur: 20335

1864 unités Globalstar SmartOne connectées au le centre de données Wialon — Ça fait 0.08% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
alarm

These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message.
Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message.
Bit 1: Input 1 state: 0 = Closed, 1 = Open
Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message
Bit 3: Input 2 state: 0 = Closed, 1 = Open
Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message.
Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message.

input_state

Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message.
Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message.
(this parameter has the same information as the second half of the alarm)

vibr Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
gps_fix_2d Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
motion Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At- Rest when the message was transmitted.
inputs

Bit (2) 0 = Good battery. 1 = replace battery.
Bit (3) 0 = GPS Data valid in this message. 1 = GPS failed in this message cycle, ignore Latitude and Longitude fields.
Bit (4) Missed Input 1. A value of 1 in this bit means that an input state change of input 1 was missed due to the transmission of a higher priority message.
Bit (5) = Missed Input 2. A value of 1 in this bit means that an input state change of Input 2 was misse
Bit (7:6) = GPS fail counter. Counts up to a maximum value of 3 upon GPS failure.

Globalstar SmartOne uses the Globalstar satellite network which provides coverage over most traveled areas of the planet

To get data from terminals please use HTTP protocol and this server address:

Wialon Hosting
Wialon Kit
http://193.193.165.165:20335/
http://193.193.165.169:20335/

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom*
Nom*
Entreprise*
Email*
Téléphone