GPS tracker Globalstar SmartOne | Integrated with Wialon

Features Globalstar SmartOne:

Caixa preta
Terminal satélite

Supported in Wialon:

Sensores digitais
Comunicação via TCP

The following data should also be added to Globalstar SmartOne unit properties section of Wialon GPS tracking software :

Device type:	Globalstar SmartOne
ID único:	serial

Specify the following parameters in configuration software or configuration Globalstar SmartOne for use in Wialon Hosting :

Porta do servidor:

20335

1823 units of Globalstar SmartOne device type are connected to Wialon Data Center. This represents 0.08% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
alarm	These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 = Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message. Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message.
input_state	Bits (7:4) message sub-type code. See subtypes below: Value is 0 in the location message. Value is 1 in the Device Turned On message. Value is 2 in the Change of Location Area alert message. Value is 3 in the Input Status Changed message. Value is 4 in the undesired input state message. Value is 5 in the re-centering message. (this parameter has the same information as the second half of the alarm)
vibr	Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
gps_fix_2d	Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
motion	Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At- Rest when the message was transmitted.
inputs	Bit (2) 0 = Good battery. 1 = replace battery. Bit (3) 0 = GPS Data valid in this message. 1 = GPS failed in this message cycle, ignore Latitude and Longitude fields. Bit (4) Missed Input 1. A value of 1 in this bit means that an input state change of input 1 was missed due to the transmission of a higher priority message. Bit (5) = Missed Input 2. A value of 1 in this bit means that an input state change of Input 2 was misse Bit (7:6) = GPS fail counter. Counts up to a maximum value of 3 upon GPS failure.

Globalstar SmartOne uses the Globalstar satellite network which provides coverage over most traveled areas of the planet

To get data from terminals please use HTTP protocol and this server address:

Wialon Hosting	Wialon Kit
http://193.193.165.165:20335/	http://193.193.165.169:20335/

Preencha um formulário de solicitação para começar

Produtos

Produtos de nicho para tarefas específicas

Globalstar SmartOne

More devices from the manufacturer

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Solicite o Wialon na sua região

Preencha um formulário de solicitação para começar