Localizador GPS Globalstar SmartOneB

Características Globalstar SmartOneB:

Caja negra
Terminal satelital

Soportado en Wialon:

Sensores Digitales
Comunicación vía TCP

Para que el sistema de rastreo Wialon identifique los datos de Globalstar SmartOneB en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo:	Globalstar SmartOneB
ID único:	serial

Indique los siguientes parámetros en el programa de configuración o en la configuración Globalstar SmartOneB para utilizarlos en Wialon Hosting :

Puerto del servidor:

20532

En el centro de servicio Wialon se utilizan 201 unidades Globalstar SmartOneB — es 0.01% de la cantidad total de dispositivos Automóvil conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro	Descripción	Unidades de medida
input_status	These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 = Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open.
msg_sub_type	Message sub-type code.
vibr	Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
gps_fix_2d	Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
motion	Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At-Rest when the message was transmitted.
num_tries	Number of Transmissions (1 to 15 Transmissions)
min_trans_interval	Minimum Interval between transmission attempts ( 5 second resolution) Default is 300 seconds
max_trans_interval	Maximum Interval between transmission attempts, Default is 600 seconds
gps_mean_search_time	Unsigned binary count in seconds for mean GPS search to acquire
gps_fails	Unsigned binary count of failed GPS attempts since last Diagnostic message
alarm	Alarm Statistics
alarm1_count	Alarm2 since last message (b7=0) / accum hours (b7=1)
alarm2_count	Alarm3 since last message (b7=0) / accum hours (b7=1)
transmissions	Transmissions since last statistics message
input№_undesired_state_time	Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
vibration_time	Accumulated time that the SMARTONE has been in a State of Vibration with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
input№_switches_number	The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)
transms_num	Number of transmissions per burst.
bat	Battery Condition. 0 = Good battery. 1 = Replace Battery
gps	GPS Subsystem Fault. 0 = GPS system OK. 1 = Fault.
transmt	Transmitter Subsystem Fault. 0 = Transmitter OK. 1 = Fault.
sched	Scheduler Subsystem Fault. 0 = OK. 1 = Fault.

Nombre del parámetro

Descripción

Unidades de medida

input_status

These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 =
Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open.

msg_sub_type

Message sub-type code.

vibr

Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.

gps_fix_2d

Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.

motion

Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At-Rest when the message was transmitted.

num_tries

Number of Transmissions (1 to 15 Transmissions)

min_trans_interval

Minimum Interval between transmission attempts ( 5 second resolution) Default is 300 seconds

max_trans_interval

Maximum Interval between transmission attempts, Default is 600 seconds

gps_mean_search_time

Unsigned binary count in seconds for mean GPS search to acquire

gps_fails

Unsigned binary count of failed GPS attempts since last Diagnostic message

alarm

Alarm Statistics

alarm1_count

Alarm2 since last message (b7=0) / accum hours (b7=1)

alarm2_count

Alarm3 since last message (b7=0) / accum hours (b7=1)

transmissions

Transmissions since last statistics message

input№_undesired_state_time

Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)

vibration_time

Accumulated time that the SMARTONE has been in a State of Vibration with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)

input№_switches_number

The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)

transms_num

Number of transmissions per burst.

bat

Battery Condition. 0 = Good battery. 1 = Replace Battery

gps

GPS Subsystem Fault. 0 = GPS system OK. 1 = Fault.

transmt

Transmitter Subsystem Fault. 0 = Transmitter OK. 1 = Fault.

sched

Scheduler Subsystem Fault. 0 = OK. 1 = Fault.

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Products

Soluciones de nicho para satisfacer las tareas específicas

Globalstar SmartOneB

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Hacerse socio

Solicite Wialon en su región

Por favor, llene la solicitud para iniciar el trabajo con Wialon