GPS трекер Globalstar SmartOneB | Интегрирован с Wialon

Особенности Globalstar SmartOneB:

Наличие черного ящика
Спутниковый терминал

Поддержано в Wialon:

Цифровые датчики
Связь через TCP

Для того чтобы система мониторинга Wialon корректно идентифицировала данные от Globalstar SmartOneB в диалоге настроек объекта, укажите следующие данные :

Тип устройства:	Globalstar SmartOneB
Уникальный ID:	serial

Укажите следующие параметры в конфигурационной программе или в конфигурации Globalstar SmartOneB для использования его в Wialon Hosting :

Порт сервера:

20532

Всего в серверном центре Wialon используется 201 объектов Globalstar SmartOneB — это составляет 0.01% от общего количества устройств в категории «Автомобильные контролеры».

График изменения количества подключений в серверном центре Wialon за последние 30 дней:

Имя параметра	Описание	Единицы измерения
input_status	These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 = Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open.
msg_sub_type	Message sub-type code.
vibr	Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.
gps_fix_2d	Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.
motion	Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At-Rest when the message was transmitted.
num_tries	Number of Transmissions (1 to 15 Transmissions)
min_trans_interval	Minimum Interval between transmission attempts ( 5 second resolution) Default is 300 seconds
max_trans_interval	Maximum Interval between transmission attempts, Default is 600 seconds
gps_mean_search_time	Unsigned binary count in seconds for mean GPS search to acquire
gps_fails	Unsigned binary count of failed GPS attempts since last Diagnostic message
alarm	Alarm Statistics
alarm1_count	Alarm2 since last message (b7=0) / accum hours (b7=1)
alarm2_count	Alarm3 since last message (b7=0) / accum hours (b7=1)
transmissions	Transmissions since last statistics message
input№_undesired_state_time	Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
vibration_time	Accumulated time that the SMARTONE has been in a State of Vibration with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)
input№_switches_number	The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)
transms_num	Number of transmissions per burst.
bat	Battery Condition. 0 = Good battery. 1 = Replace Battery
gps	GPS Subsystem Fault. 0 = GPS system OK. 1 = Fault.
transmt	Transmitter Subsystem Fault. 0 = Transmitter OK. 1 = Fault.
sched	Scheduler Subsystem Fault. 0 = OK. 1 = Fault.

Имя параметра

Описание

Единицы измерения

input_status

These bits reflect the state of the inputs and indicate which one, if any, triggered an Input Status Changed message. Bit 0: Input 1 change: 0 = Did not trigger message, 1 = Triggered message. Bit 1: Input 1 state: 0 =
Closed, 1 = Open Bit 2: Input 2 change: 0 = Did not trigger message, 1 = Triggered message Bit 3: Input 2 state: 0 = Closed, 1 = Open.

msg_sub_type

Message sub-type code.

vibr

Value 1 = Unit is in a state of vibration. Value 0 = Unit is not in a state of vibration.

gps_fix_2d

Value 1 = GPS data reported is from a 2D fix. (Only 3 satellites were used in the fix.) Value 0 = GPS data reported is from a 3D fix.

motion

Value 1 = Device was In-Motion when the message was transmitted. Value 0 = Device was At-Rest when the message was transmitted.

num_tries

Number of Transmissions (1 to 15 Transmissions)

min_trans_interval

Minimum Interval between transmission attempts ( 5 second resolution) Default is 300 seconds

max_trans_interval

Maximum Interval between transmission attempts, Default is 600 seconds

gps_mean_search_time

Unsigned binary count in seconds for mean GPS search to acquire

gps_fails

Unsigned binary count of failed GPS attempts since last Diagnostic message

alarm

Alarm Statistics

alarm1_count

Alarm2 since last message (b7=0) / accum hours (b7=1)

alarm2_count

Alarm3 since last message (b7=0) / accum hours (b7=1)

transmissions

Transmissions since last statistics message

input№_undesired_state_time

Accumulated time that Input 1 has been in its undesired state with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)

vibration_time

Accumulated time that the SMARTONE has been in a State of Vibration with a resolution of 10 minutes. For example: 1 hour would be represented as a value of 6, 2 hours as a value of 12, etc. This resolution results in a rollover rate of a total time accumulation of approximately 1.25 years. (OxFFFF means that Input 1 Accumulate has been turned off)

input№_switches_number

The total number of openings or closings of input 1 as selected by the user. (OxFF means that Input 1 Accumulate has been turned off)

transms_num

Number of transmissions per burst.

bat

Battery Condition. 0 = Good battery. 1 = Replace Battery

gps

GPS Subsystem Fault. 0 = GPS system OK. 1 = Fault.

transmt

Transmitter Subsystem Fault. 0 = Transmitter OK. 1 = Fault.

sched

Scheduler Subsystem Fault. 0 = OK. 1 = Fault.

Заполните заявку для начала работы с Wialon

Продукты

Нишевые продукты для решения точечных задач

Globalstar SmartOneB

Другие устройства производителя

Работайте с Wialon и достигайте самых амбициозных целей в телематике

Станьте партнером

Закажите Wialon в вашем регионе

Заполните заявку для начала работы с Wialon