| pwr_ext |
Voltage of external power supply |
V |
| pwr_int |
Power supply internal battery |
V |
| gsm |
GSM signal quality |
|
| gsm_status |
GSM status |
|
| dt |
0-Real time report |
|
| fuel_consumption |
Fuel Used in 0.1 liter |
|
| analog_volt |
Analog voltage reading |
|
| max_speed |
Maximum speed between two reports |
|
| gl |
Google Link (N/A in AX5) |
|
| gx |
X-axis acceleration |
0.0098*m/s2
|
| gy |
Y-axis acceleration |
0.0098*m/s2
|
| gz |
Z-axis acceleration |
0.0098*m/s2
|
| motion |
Vehicle motion event status |
|
| engine |
Engine event status |
|
| Model Name: |
Device Model Name |
|
| Firmware Ver: |
Device firmware version information |
|
| IMEI: |
International Mobile Equipment Identity number (Not available in AY5(i); 0 is shown) |
|
| IMSI: |
International Mobile Subscriber Identity (Not available in AY5(i); 0 is shown) |
|
| CID: |
Card identification number of SIM card (Not available in AY5(i); 0 is shown) |
|
| Main Volt: |
Main power voltage in 0.1 |
V |
| Battery Volt: |
Backup battery voltage in 0.1 |
V |
| SATS: |
Numbers of GPS satellite currently used |
|
| GSM Status: |
GSM Network registration status (Not available in AY5(i); 0 is shown):
0: Network not registered
1: Registered to home network
2: Searching for available network
3: Registration denied
4: Unknown
5: Registered, roaming
|
|
| GPS Status: |
GPS antenna status:
Bit 0: 0 -> GPS antenna connected
          1 -> GPS antenna disconnected
Bit 1: 0 -> GPS antenna cable OK
          1 -> GPS antenna cable short circuit
Bit 2: 0 -> GPS signal reception OK
          1 -> GPS signal reception timeout
|
|
| tracking_mode |
The GPS tracking Mode parameter can be in conjunction with the following bits:
Bit 0: Time mode
Bit 1: Distance mode
Bit 2: ACC status (Must combine with Bit 0 or Bit 1)
Bit 3: Heading change condition
Bit 4: Minimum speed (Must combine with Bit 0 or Bit 1)
Bit 5: Engine status = ON. (Must combine with Bit 0 or Bit 1)
Bit 6: Motion status = ON. (Must combine with Bit 0 or Bit 1)
Bit 7: Logical Operation Mode (0=AND; 1=OR; Default=0) This mode only works when combining Time, Distance, and/or Heading change.
Bit 8: Reset tracking timer when event report is sent
Bit 9: Report with unique ID when in Distance Mode (Must combine with Bit 1)
|
|
| min_send_time |
Minimum time in seconds that must elapse before reporting next position. (Min. 1 seconds) |
|
| min_send_dist |
Minimum distance in multiple of 10 meters that must be traveled before reporting next position. (Min. 20 meters) |
|
| min_heading |
Minimum heading in degree that must be changed before reporting next position. (15..180) |
|
| min_speed |
Minimum speed in km/h that must be achieved before reporting next position. |
|
| track_times |
Specify tracking times. =0 means forever tracking.
|
|
| dest_type |
Specify the destination for tracking report position The parameter is in conjunction with the following bits:
0: Default communication type. (i.e. Command issuer)
Bit 0: SMS
Bit 1: GPRS (This is the only option for AY5)
Bit 2: USSD
Bit 3: Serial
|
|
| sched |
Specify the schedule for the report. The parameter is in conjunction with the following bits:
0 – indicates use no schedule (i.e. always on)
Bit 0 – Schedule 1
Bit 1 – Schedule 2
Bit 2 – Schedule 3
Bit 3 – Schedule 4
Bit 4 – Schedule 5
Bit 5 – Schedule 6
Bit 6 – Schedule 7
Bit 7 – Schedule 8
|
|
| acc_off_time |
Minimum time in seconds that must elapse before reporting next position while the ACC is in Off status.
ACC status in Mode must be set in order to use this time interval. (Min. 1 seconds) |
|
| coll_num |
Number of position to be put into one TCP/UDP packet |
|
| temp_a_id |
The sensor ID corresponding to temperature A |
|
| curr_a_temp |
The temperature reading from sensor ID A |
|
| temp_b_id |
The sensor ID corresponding to temperature B |
|
| curr_b_temp |
The temperature reading from sensor ID B |
|
| sensor_index |
The connected port number where the Temperature Sensor connected with by different user.
1: First detected sensor
2: Second detected sensor
|
|
| min_temp |
Minimum temperature value, and is in 0.1 |
°C |
| max_temp |
Maximum temperature value, and is in 0.1 |
°C |
| hold_duration |
A temperature holding time, and is in minute unit. |
|
| sensor_id |
Temperature sensor ID. This temperature sensor can be set to be index 1 or 2 by specifying the ID in this field. |
|
| gps_tm |
GPS Time. Unix Timestamp |
s |
| rtc_tm |
RTC Time. Unix Timestamp |
s |
| snd_tm |
Position Sending Time. Unix Timestamp |
s |
