| acc |
Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On
|
|
| acc_status |
Accelerometer sensor status of the BLE device (BXP-Tag)
|
|
| adv_cnt |
Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM)
|
|
| adv_data |
Raw advertising data of the BLE device
|
|
| adv_interval |
Interval of sending adv_data
|
ms |
| adv_name |
Asset Name
|
|
| axis_x |
Acceleration along the X axis
|
mg |
| axis_y |
Acceleration along the Y axis
|
mg |
| axis_z |
Acceleration along the Z axis
|
mg |
| batt_vol |
Volume of Internal Battery
|
mV |
| ble_batt_vol |
Battery voltage of the MOKO Button device the gateway is connected to
|
mV |
| ble_company |
Company name of the connected MOKO Button device
|
|
| ble_dfu_pct |
Firmware upgrade progress of the connected MOKO Button device
|
% |
| ble_dfu_result |
Firmware upgrade result of the connected MOKO Button device - 0: Success
- 1: BLE button is not connected
- 2: Command is not allowed in current mode
- 3: Failed to obtain upgrade files
- 4: Command timeout
- 5: Upgrade failed
|
|
| ble_disconnect_rsn |
Reason of the disconnection from the MOKO Button device - 0: Abnormally disconnect
- 1: Communicate timeout
|
|
| ble_firmware_ver |
Firmware version of the connected MOKO Button device
|
|
| ble_hardware_ver |
Hardware version of the connected MOKO Button device
|
|
| ble_mac |
Mac of the MOKO Button device the gateway is connected to
|
|
| ble_product_model |
Product model of the connected MOKO Button device
|
|
| ble_result |
Result code of the command sent to the MOKO Button device Connection result: - 0: Connect succeed
- 1: Connection is not allowed on current mode
- 2: Exceed the connection number
- 3: BLE device has been connected
- 4: BLE device is out of range
- 5: BLE device is not connectable
- 6: Connect failed
- 7: Device type error
- 8: Password error
Result of the other commands: - 0: Command success
- 1: BLE device is not connected
- 2: Command is not allowed in current mode
|
|
| ble_software_ver |
Software version of the connected MOKO Button device
|
|
| cell_id |
Cell ID (CI) of the base station, LBS positioning data
|
|
| cert_result |
MQTT SSL certificate download result - -1: In progress
- 0: Failed
- 1: Success
|
|
| connectable |
Status of the BLE device 0: Not Connectable 1: Connectable
|
|
| csq |
Cellular signal quality of the gateway, 0-31
|
|
| data_block_1 |
The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_2 |
The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_3 |
The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_4 |
The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_5 |
The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_6 |
The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_7 |
The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_8 |
The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_9 |
The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_10 |
The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| delay_response_status |
Delay response status of the MK PIR device - 0: Low delay
- 1: Medium delay
- 2: High delay
|
|
| detection_status |
Motion detection status of the MK PIR sensor - 0: No effective motion detected
- 1: Effective motion detected
|
|
| device_id |
Device id of the BLE device (BXP-Button)
|
|
| device_name |
Name of the BLE device (BXP-Button, BXP-Tag)
|
|
| door_status |
Current status of the door sensor 0: Closed 1: Open
|
|
| double_alarm |
Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| double_alarm_cnt |
Number of the double press alarms of the connected MOKO Button device
|
|
| factory_reset |
Set to 1 when the gateway is restored to the factory settings by the physical button
|
|
| firmware_type |
Firmware type of the BLE device (BXP-Button)
|
|
| firmware_ver |
Firmware version of the BLE device
|
|
| fix_mode |
Positioning mode used for the reported fix - 0: Periodic fix
- 1: Motion fix
- 2: Request fix
|
|
| fix_result |
Result of the positioning attempt - 0: GPS fix successful
- 1: LBS fix successful
- 2: Fix failed cause by the request fix interruption
- 3: Fix failed caused by GPS serial port is occupied
- 4: Fix failed caused by GPS timeout
- 5: Fix failed caused by GPS fix timeout
- 6: Fix failed caused by PDOP limited
- 7: LBS fix failed
|
|
| frame_type |
Advertising frame type of the BLE device (BXP-Button) - 32 (0X20): Single press mode
- 33 (0X21): Double press mode
- 34 (0X22): Long press mode
- 35 (0X23): Abnormal inactivity mode
|
|
| full_scale |
Full-scale range of the accelerometer of the BLE device
|
g |
| hall_status |
Hall sensor status of the BLE device (BXP-Tag)
|
|
| hall_trigger_cnt |
Number of the hall sensor trigger events of the BLE device (BXP-Tag)
|
|
| have_acc_sensor |
Status parameter that shows if the accelerometer sensor is equipped
|
|
| have_door_sensor |
Status parameter that shows if the hall door sensor is connected
|
|
| have_light_sensor |
Status parameter that shows if the light sensor is connected
|
|
| humidity |
Humidity measured by the BLE device (BXP-TH)
|
% |
| imei |
IMEI of the gateway cellular module
|
|
| inactivity_alarm |
Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| instance |
Instance of the BLE device (Eddystone-UID)
|
|
| lac |
Location area code (LAC/TAC) of the base station, LBS positioning data
|
|
| light_sensor_status |
Current status of the light sensor
0: Not activated 1: Activated
|
|
| long_alarm |
Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| long_alarm_cnt |
Number of the long press alarms of the connected MOKO Button device
|
|
| low_batt_alarm |
Set to 1 when the gateway battery voltage drops below the configured threshold
|
|
| mac |
Mac of the connected BLE Device
|
|
| major |
Major value of the BLE device (iBeacon, MK PIR)
|
|
| mfg_code |
Manufacturer vendor code of the BLE device (MK TOF)
|
|
| minor |
Minor value of the BLE device (iBeacon, MK PIR)
|
|
| motion_threshold |
Motion detection threshold of the accelerometer of the BLE device
|
g |
| motion_trigger_cnt |
Number of the motion trigger events of the BLE device (BXP-Tag)
|
|
| namespace |
Namespace of the BLE device (Eddystone-UID)
|
|
| net_type |
Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS
|
|
| ota_result |
Result of the gateway firmware upgrade - -1: OTA in progress
- 0: OTA failed
- 1: OTA successful
|
|
| passwd_verification |
Shows if the BLE device requires password verification
|
|
| pwr_disconnect_alarm |
Set to 1 when the gateway detects that the external power is disconnected
|
|
| ranging_data |
Ranging data of the BLE device, the reference signal strength used for the distance calculation
|
dBm |
| ranging_distance |
Distance measured by the BLE device (MK TOF)
|
mm |
| remaining_packets |
Number of the buffered packets left to upload
|
|
| rsp_data |
Raw scan response data of the BLE device
|
|
| rssi |
Signal Strength of the BLE device
|
dBm |
| rssi_0m |
Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL)
|
dBm |
| rssi_1m |
Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR)
|
dBm |
| sampling_rate |
Sampling rate of the accelerometer of the BLE device (BXP-ACC)
|
Hz |
| sec_cnt |
Time elapsed since the BLE device power-up (Eddystone-TLM)
|
s |
| sensor_sensitivity |
Sensitivity of the MK PIR sensor - 0: Low sensitivity
- 1: Medium sensitivity
- 2: High sensitivity
|
|
| single_alarm |
Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| single_alarm_cnt |
Number of the single press alarms of the connected MOKO Button device
|
|
| tag_id |
Tag id of the BLE device (BXP-Tag)
|
|
| temperature |
Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button)
|
°C |
| timezone |
Time zone of the local time reported by the gateway
|
h |
| tlm_version |
Version of the telemetry frame of the BLE device (Eddystone-TLM)
|
|
| trigger_count |
Number of the triggers of the BLE device (BXP-Button)
|
|
| trigger_status |
Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered
|
|
| tx_power |
Transmission power of the BLE device
|
dBm |
| type |
Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof
|
|
| type_code |
Code of the advertising data type of the BLE device - 0: iBeacon
- 1: Eddystone-UID
- 2: Eddystone-URL
- 3: Eddystone-TLM
- 4: BXP-Device info
- 5: BXP-ACC
- 6: BXP-TH
- 7: BXP-Button
- 8: BXP-Tag
- 9: PIR
- 10: Other type
- 11: TOF
|
|
| uploaded_packets |
Number of the buffered packets uploaded by the gateway
|
|
| url |
URL advertised by the BLE device (Eddystone-URL)
|
|
| user_data |
User data of the BLE device (MK TOF)
|
|
| uuid |
UUID of the BLE device (iBeacon)
|
|
| acc |
Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On
|
|
| acc |
Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On
|
|
| acc_status |
Accelerometer sensor status of the BLE device (BXP-Tag)
|
|
| acc_status |
Accelerometer sensor status of the BLE device (BXP-Tag)
|
|
| adv_cnt |
Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM)
|
|
| adv_cnt |
Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM)
|
|
| adv_data |
Raw advertising data of the BLE device
|
|
| adv_data |
Raw advertising data of the BLE device
|
|
| adv_interval |
Interval of sending adv_data
|
ms |
| adv_interval |
Interval of sending adv_data
|
ms |
| adv_name |
Asset Name
|
|
| adv_name |
Asset Name
|
|
| axis_x |
Acceleration along the X axis
|
mg |
| axis_x |
Acceleration along the X axis
|
mg |
| axis_y |
Acceleration along the Y axis
|
mg |
| axis_y |
Acceleration along the Y axis
|
mg |
| axis_z |
Acceleration along the Z axis
|
mg |
| axis_z |
Acceleration along the Z axis
|
mg |
| batt_vol |
Volume of Internal Battery
|
mV |
| batt_vol |
Volume of Internal Battery
|
mV |
| ble_batt_vol |
Battery voltage of the MOKO Button device the gateway is connected to
|
mV |
| ble_batt_vol |
Battery voltage of the MOKO Button device the gateway is connected to
|
mV |
| ble_company |
Company name of the connected MOKO Button device
|
|
| ble_company |
Company name of the connected MOKO Button device
|
|
| ble_dfu_pct |
Firmware upgrade progress of the connected MOKO Button device
|
% |
| ble_dfu_pct |
Firmware upgrade progress of the connected MOKO Button device
|
% |
| ble_dfu_result |
Firmware upgrade result of the connected MOKO Button device - 0: Success
- 1: BLE button is not connected
- 2: Command is not allowed in current mode
- 3: Failed to obtain upgrade files
- 4: Command timeout
- 5: Upgrade failed
|
|
| ble_dfu_result |
Firmware upgrade result of the connected MOKO Button device - 0: Success
- 1: BLE button is not connected
- 2: Command is not allowed in current mode
- 3: Failed to obtain upgrade files
- 4: Command timeout
- 5: Upgrade failed
|
|
| ble_disconnect_rsn |
Reason of the disconnection from the MOKO Button device - 0: Abnormally disconnect
- 1: Communicate timeout
|
|
| ble_disconnect_rsn |
Reason of the disconnection from the MOKO Button device - 0: Abnormally disconnect
- 1: Communicate timeout
|
|
| ble_firmware_ver |
Firmware version of the connected MOKO Button device
|
|
| ble_firmware_ver |
Firmware version of the connected MOKO Button device
|
|
| ble_hardware_ver |
Hardware version of the connected MOKO Button device
|
|
| ble_hardware_ver |
Hardware version of the connected MOKO Button device
|
|
| ble_mac |
Mac of the MOKO Button device the gateway is connected to
|
|
| ble_mac |
Mac of the MOKO Button device the gateway is connected to
|
|
| ble_product_model |
Product model of the connected MOKO Button device
|
|
| ble_product_model |
Product model of the connected MOKO Button device
|
|
| ble_result |
Result code of the command sent to the MOKO Button device Connection result: - 0: Connect succeed
- 1: Connection is not allowed on current mode
- 2: Exceed the connection number
- 3: BLE device has been connected
- 4: BLE device is out of range
- 5: BLE device is not connectable
- 6: Connect failed
- 7: Device type error
- 8: Password error
Result of the other commands: - 0: Command success
- 1: BLE device is not connected
- 2: Command is not allowed in current mode
|
|
| ble_result |
Result code of the command sent to the MOKO Button device Connection result: - 0: Connect succeed
- 1: Connection is not allowed on current mode
- 2: Exceed the connection number
- 3: BLE device has been connected
- 4: BLE device is out of range
- 5: BLE device is not connectable
- 6: Connect failed
- 7: Device type error
- 8: Password error
Result of the other commands: - 0: Command success
- 1: BLE device is not connected
- 2: Command is not allowed in current mode
|
|
| ble_software_ver |
Software version of the connected MOKO Button device
|
|
| ble_software_ver |
Software version of the connected MOKO Button device
|
|
| cell_id |
Cell ID (CI) of the base station, LBS positioning data
|
|
| cell_id |
Cell ID (CI) of the base station, LBS positioning data
|
|
| cert_result |
MQTT SSL certificate download result - -1: In progress
- 0: Failed
- 1: Success
|
|
| cert_result |
MQTT SSL certificate download result - -1: In progress
- 0: Failed
- 1: Success
|
|
| connectable |
Status of the BLE device 0: Not Connectable 1: Connectable
|
|
| connectable |
Status of the BLE device 0: Not Connectable 1: Connectable
|
|
| csq |
Cellular signal quality of the gateway, 0-31
|
|
| csq |
Cellular signal quality of the gateway, 0-31
|
|
| data_block_1 |
The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_1 |
The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_2 |
The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_2 |
The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_3 |
The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_3 |
The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_4 |
The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_4 |
The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_5 |
The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_5 |
The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_6 |
The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_6 |
The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_7 |
The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_7 |
The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_8 |
The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_8 |
The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_9 |
The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_9 |
The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_10 |
The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| data_block_10 |
The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command
|
|
| delay_response_status |
Delay response status of the MK PIR device - 0: Low delay
- 1: Medium delay
- 2: High delay
|
|
| delay_response_status |
Delay response status of the MK PIR device - 0: Low delay
- 1: Medium delay
- 2: High delay
|
|
| detection_status |
Motion detection status of the MK PIR sensor - 0: No effective motion detected
- 1: Effective motion detected
|
|
| detection_status |
Motion detection status of the MK PIR sensor - 0: No effective motion detected
- 1: Effective motion detected
|
|
| device_id |
Device id of the BLE device (BXP-Button)
|
|
| device_id |
Device id of the BLE device (BXP-Button)
|
|
| device_name |
Name of the BLE device (BXP-Button, BXP-Tag)
|
|
| device_name |
Name of the BLE device (BXP-Button, BXP-Tag)
|
|
| door_status |
Current status of the door sensor 0: Closed 1: Open
|
|
| door_status |
Current status of the door sensor 0: Closed 1: Open
|
|
| double_alarm |
Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| double_alarm |
Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| double_alarm_cnt |
Number of the double press alarms of the connected MOKO Button device
|
|
| double_alarm_cnt |
Number of the double press alarms of the connected MOKO Button device
|
|
| factory_reset |
Set to 1 when the gateway is restored to the factory settings by the physical button
|
|
| factory_reset |
Set to 1 when the gateway is restored to the factory settings by the physical button
|
|
| firmware_type |
Firmware type of the BLE device (BXP-Button)
|
|
| firmware_type |
Firmware type of the BLE device (BXP-Button)
|
|
| firmware_ver |
Firmware version of the BLE device
|
|
| firmware_ver |
Firmware version of the BLE device
|
|
| fix_mode |
Positioning mode used for the reported fix - 0: Periodic fix
- 1: Motion fix
- 2: Request fix
|
|
| fix_mode |
Positioning mode used for the reported fix - 0: Periodic fix
- 1: Motion fix
- 2: Request fix
|
|
| fix_result |
Result of the positioning attempt - 0: GPS fix successful
- 1: LBS fix successful
- 2: Fix failed cause by the request fix interruption
- 3: Fix failed caused by GPS serial port is occupied
- 4: Fix failed caused by GPS timeout
- 5: Fix failed caused by GPS fix timeout
- 6: Fix failed caused by PDOP limited
- 7: LBS fix failed
|
|
| fix_result |
Result of the positioning attempt - 0: GPS fix successful
- 1: LBS fix successful
- 2: Fix failed cause by the request fix interruption
- 3: Fix failed caused by GPS serial port is occupied
- 4: Fix failed caused by GPS timeout
- 5: Fix failed caused by GPS fix timeout
- 6: Fix failed caused by PDOP limited
- 7: LBS fix failed
|
|
| frame_type |
Advertising frame type of the BLE device (BXP-Button) - 32 (0X20): Single press mode
- 33 (0X21): Double press mode
- 34 (0X22): Long press mode
- 35 (0X23): Abnormal inactivity mode
|
|
| frame_type |
Advertising frame type of the BLE device (BXP-Button) - 32 (0X20): Single press mode
- 33 (0X21): Double press mode
- 34 (0X22): Long press mode
- 35 (0X23): Abnormal inactivity mode
|
|
| full_scale |
Full-scale range of the accelerometer of the BLE device
|
g |
| full_scale |
Full-scale range of the accelerometer of the BLE device
|
g |
| hall_status |
Hall sensor status of the BLE device (BXP-Tag)
|
|
| hall_status |
Hall sensor status of the BLE device (BXP-Tag)
|
|
| hall_trigger_cnt |
Number of the hall sensor trigger events of the BLE device (BXP-Tag)
|
|
| hall_trigger_cnt |
Number of the hall sensor trigger events of the BLE device (BXP-Tag)
|
|
| have_acc_sensor |
Status parameter that shows if the accelerometer sensor is equipped
|
|
| have_acc_sensor |
Status parameter that shows if the accelerometer sensor is equipped
|
|
| have_door_sensor |
Status parameter that shows if the hall door sensor is connected
|
|
| have_door_sensor |
Status parameter that shows if the hall door sensor is connected
|
|
| have_light_sensor |
Status parameter that shows if the light sensor is connected
|
|
| have_light_sensor |
Status parameter that shows if the light sensor is connected
|
|
| humidity |
Humidity measured by the BLE device (BXP-TH)
|
% |
| humidity |
Humidity measured by the BLE device (BXP-TH)
|
% |
| imei |
IMEI of the gateway cellular module
|
|
| imei |
IMEI of the gateway cellular module
|
|
| inactivity_alarm |
Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| inactivity_alarm |
Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| instance |
Instance of the BLE device (Eddystone-UID)
|
|
| instance |
Instance of the BLE device (Eddystone-UID)
|
|
| lac |
Location area code (LAC/TAC) of the base station, LBS positioning data
|
|
| lac |
Location area code (LAC/TAC) of the base station, LBS positioning data
|
|
| light_sensor_status |
Current status of the light sensor
0: Not activated 1: Activated
|
|
| light_sensor_status |
Current status of the light sensor
0: Not activated 1: Activated
|
|
| long_alarm |
Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| long_alarm |
Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| long_alarm_cnt |
Number of the long press alarms of the connected MOKO Button device
|
|
| long_alarm_cnt |
Number of the long press alarms of the connected MOKO Button device
|
|
| low_batt_alarm |
Set to 1 when the gateway battery voltage drops below the configured threshold
|
|
| low_batt_alarm |
Set to 1 when the gateway battery voltage drops below the configured threshold
|
|
| mac |
Mac of the connected BLE Device
|
|
| mac |
Mac of the connected BLE Device
|
|
| major |
Major value of the BLE device (iBeacon, MK PIR)
|
|
| major |
Major value of the BLE device (iBeacon, MK PIR)
|
|
| mfg_code |
Manufacturer vendor code of the BLE device (MK TOF)
|
|
| mfg_code |
Manufacturer vendor code of the BLE device (MK TOF)
|
|
| minor |
Minor value of the BLE device (iBeacon, MK PIR)
|
|
| minor |
Minor value of the BLE device (iBeacon, MK PIR)
|
|
| motion_threshold |
Motion detection threshold of the accelerometer of the BLE device
|
g |
| motion_threshold |
Motion detection threshold of the accelerometer of the BLE device
|
g |
| motion_trigger_cnt |
Number of the motion trigger events of the BLE device (BXP-Tag)
|
|
| motion_trigger_cnt |
Number of the motion trigger events of the BLE device (BXP-Tag)
|
|
| namespace |
Namespace of the BLE device (Eddystone-UID)
|
|
| namespace |
Namespace of the BLE device (Eddystone-UID)
|
|
| net_type |
Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS
|
|
| net_type |
Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS
|
|
| ota_result |
Result of the gateway firmware upgrade - -1: OTA in progress
- 0: OTA failed
- 1: OTA successful
|
|
| ota_result |
Result of the gateway firmware upgrade - -1: OTA in progress
- 0: OTA failed
- 1: OTA successful
|
|
| passwd_verification |
Shows if the BLE device requires password verification
|
|
| passwd_verification |
Shows if the BLE device requires password verification
|
|
| pwr_disconnect_alarm |
Set to 1 when the gateway detects that the external power is disconnected
|
|
| pwr_disconnect_alarm |
Set to 1 when the gateway detects that the external power is disconnected
|
|
| ranging_data |
Ranging data of the BLE device, the reference signal strength used for the distance calculation
|
dBm |
| ranging_data |
Ranging data of the BLE device, the reference signal strength used for the distance calculation
|
dBm |
| ranging_distance |
Distance measured by the BLE device (MK TOF)
|
mm |
| ranging_distance |
Distance measured by the BLE device (MK TOF)
|
mm |
| remaining_packets |
Number of the buffered packets left to upload
|
|
| remaining_packets |
Number of the buffered packets left to upload
|
|
| rsp_data |
Raw scan response data of the BLE device
|
|
| rsp_data |
Raw scan response data of the BLE device
|
|
| rssi |
Signal Strength of the BLE device
|
dBm |
| rssi |
Signal Strength of the BLE device
|
dBm |
| rssi_0m |
Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL)
|
dBm |
| rssi_0m |
Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL)
|
dBm |
| rssi_1m |
Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR)
|
dBm |
| rssi_1m |
Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR)
|
dBm |
| sampling_rate |
Sampling rate of the accelerometer of the BLE device (BXP-ACC)
|
Hz |
| sampling_rate |
Sampling rate of the accelerometer of the BLE device (BXP-ACC)
|
Hz |
| sec_cnt |
Time elapsed since the BLE device power-up (Eddystone-TLM)
|
s |
| sec_cnt |
Time elapsed since the BLE device power-up (Eddystone-TLM)
|
s |
| sensor_sensitivity |
Sensitivity of the MK PIR sensor - 0: Low sensitivity
- 1: Medium sensitivity
- 2: High sensitivity
|
|
| sensor_sensitivity |
Sensitivity of the MK PIR sensor - 0: Low sensitivity
- 1: Medium sensitivity
- 2: High sensitivity
|
|
| single_alarm |
Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| single_alarm |
Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered
|
|
| single_alarm_cnt |
Number of the single press alarms of the connected MOKO Button device
|
|
| single_alarm_cnt |
Number of the single press alarms of the connected MOKO Button device
|
|
| tag_id |
Tag id of the BLE device (BXP-Tag)
|
|
| tag_id |
Tag id of the BLE device (BXP-Tag)
|
|
| temperature |
Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button)
|
°C |
| temperature |
Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button)
|
°C |
| timezone |
Time zone of the local time reported by the gateway
|
h |
| timezone |
Time zone of the local time reported by the gateway
|
h |
| tlm_version |
Version of the telemetry frame of the BLE device (Eddystone-TLM)
|
|
| tlm_version |
Version of the telemetry frame of the BLE device (Eddystone-TLM)
|
|
| trigger_count |
Number of the triggers of the BLE device (BXP-Button)
|
|
| trigger_count |
Number of the triggers of the BLE device (BXP-Button)
|
|
| trigger_status |
Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered
|
|
| trigger_status |
Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered
|
|
| tx_power |
Transmission power of the BLE device
|
dBm |
| tx_power |
Transmission power of the BLE device
|
dBm |
| type |
Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof
|
|
| type |
Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof
|
|
| type_code |
Code of the advertising data type of the BLE device - 0: iBeacon
- 1: Eddystone-UID
- 2: Eddystone-URL
- 3: Eddystone-TLM
- 4: BXP-Device info
- 5: BXP-ACC
- 6: BXP-TH
- 7: BXP-Button
- 8: BXP-Tag
- 9: PIR
- 10: Other type
- 11: TOF
|
|
| type_code |
Code of the advertising data type of the BLE device - 0: iBeacon
- 1: Eddystone-UID
- 2: Eddystone-URL
- 3: Eddystone-TLM
- 4: BXP-Device info
- 5: BXP-ACC
- 6: BXP-TH
- 7: BXP-Button
- 8: BXP-Tag
- 9: PIR
- 10: Other type
- 11: TOF
|
|
| uploaded_packets |
Number of the buffered packets uploaded by the gateway
|
|
| url |
URL advertised by the BLE device (Eddystone-URL)
|
|
| user_data |
User data of the BLE device (MK TOF)
|
|
| uuid |
UUID of the BLE device (iBeacon)
|
|
| uploaded_packets |
Number of the buffered packets uploaded by the gateway
|
|
| url |
URL advertised by the BLE device (Eddystone-URL)
|
|
| user_data |
User data of the BLE device (MK TOF)
|
|
| uuid |
UUID of the BLE device (iBeacon)
|
|
