Número de unidades
The following data should also be added to MKGW4 unit properties section of Wialon GPS tracking software :
| Device type: | MKGW4 |
| ID único: | custom |
Specify the following parameters in configuration software or configuration MKGW4 for use in Wialon Hosting :
| Porta do servidor: | 22990 |
0 units of MKGW4 device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.
Below chart represents the dynamic of connections in the last 30 days:
| Parameter name | Description | Units |
|---|---|---|
| acc | Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On |
|
| acc_status | Accelerometer sensor status of the BLE device (BXP-Tag) |
|
| adv_cnt | Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM) |
|
| adv_data | Raw advertising data of the BLE device |
|
| adv_interval | Interval of sending adv_data |
ms |
| adv_name | Asset Name |
|
| axis_x | Acceleration along the X axis |
mg |
| axis_y | Acceleration along the Y axis |
mg |
| axis_z | Acceleration along the Z axis |
mg |
| batt_vol | Volume of Internal Battery |
mV |
| ble_batt_vol | Battery voltage of the MOKO Button device the gateway is connected to |
mV |
| ble_company | Company name of the connected MOKO Button device |
|
| ble_dfu_pct | Firmware upgrade progress of the connected MOKO Button device |
% |
| ble_dfu_result | Firmware upgrade result of the connected MOKO Button device
|
|
| ble_disconnect_rsn | Reason of the disconnection from the MOKO Button device
|
|
| ble_firmware_ver | Firmware version of the connected MOKO Button device |
|
| ble_hardware_ver | Hardware version of the connected MOKO Button device |
|
| ble_mac | Mac of the MOKO Button device the gateway is connected to |
|
| ble_product_model | Product model of the connected MOKO Button device |
|
| ble_result | Result code of the command sent to the MOKO Button device Connection result:
Result of the other commands:
|
|
| ble_software_ver | Software version of the connected MOKO Button device |
|
| cell_id | Cell ID (CI) of the base station, LBS positioning data |
|
| cert_result | MQTT SSL certificate download result
|
|
| connectable | Status of the BLE device 0: Not Connectable 1: Connectable |
|
| csq | Cellular signal quality of the gateway, 0-31 |
|
| data_block_1 | The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_2 | The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_3 | The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_4 | The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_5 | The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_6 | The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_7 | The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_8 | The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_9 | The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_10 | The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| delay_response_status | Delay response status of the MK PIR device
|
|
| detection_status | Motion detection status of the MK PIR sensor
|
|
| device_id | Device id of the BLE device (BXP-Button) |
|
| device_name | Name of the BLE device (BXP-Button, BXP-Tag) |
|
| door_status | Current status of the door sensor 0: Closed 1: Open |
|
| double_alarm | Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| double_alarm_cnt | Number of the double press alarms of the connected MOKO Button device |
|
| factory_reset | Set to 1 when the gateway is restored to the factory settings by the physical button |
|
| firmware_type | Firmware type of the BLE device (BXP-Button) |
|
| firmware_ver | Firmware version of the BLE device |
|
| fix_mode | Positioning mode used for the reported fix
|
|
| fix_result | Result of the positioning attempt
|
|
| frame_type | Advertising frame type of the BLE device (BXP-Button)
|
|
| full_scale | Full-scale range of the accelerometer of the BLE device |
g |
| hall_status | Hall sensor status of the BLE device (BXP-Tag) |
|
| hall_trigger_cnt | Number of the hall sensor trigger events of the BLE device (BXP-Tag) |
|
| have_acc_sensor | Status parameter that shows if the accelerometer sensor is equipped |
|
| have_door_sensor | Status parameter that shows if the hall door sensor is connected |
|
| have_light_sensor | Status parameter that shows if the light sensor is connected |
|
| humidity | Humidity measured by the BLE device (BXP-TH) |
% |
| imei | IMEI of the gateway cellular module |
|
| inactivity_alarm | Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| instance | Instance of the BLE device (Eddystone-UID) |
|
| lac | Location area code (LAC/TAC) of the base station, LBS positioning data |
|
| light_sensor_status | Current status of the light sensor 1: Activated |
|
| long_alarm | Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| long_alarm_cnt | Number of the long press alarms of the connected MOKO Button device |
|
| low_batt_alarm | Set to 1 when the gateway battery voltage drops below the configured threshold |
|
| mac | Mac of the connected BLE Device |
|
| major | Major value of the BLE device (iBeacon, MK PIR) |
|
| mfg_code | Manufacturer vendor code of the BLE device (MK TOF) |
|
| minor | Minor value of the BLE device (iBeacon, MK PIR) |
|
| motion_threshold | Motion detection threshold of the accelerometer of the BLE device |
g |
| motion_trigger_cnt | Number of the motion trigger events of the BLE device (BXP-Tag) |
|
| namespace | Namespace of the BLE device (Eddystone-UID) |
|
| net_type | Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS |
|
| ota_result | Result of the gateway firmware upgrade
|
|
| passwd_verification | Shows if the BLE device requires password verification |
|
| pwr_disconnect_alarm | Set to 1 when the gateway detects that the external power is disconnected |
|
| ranging_data | Ranging data of the BLE device, the reference signal strength used for the distance calculation |
dBm |
| ranging_distance | Distance measured by the BLE device (MK TOF) |
mm |
| remaining_packets | Number of the buffered packets left to upload |
|
| rsp_data | Raw scan response data of the BLE device |
|
| rssi | Signal Strength of the BLE device |
dBm |
| rssi_0m | Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL) |
dBm |
| rssi_1m | Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR) |
dBm |
| sampling_rate | Sampling rate of the accelerometer of the BLE device (BXP-ACC) |
Hz |
| sec_cnt | Time elapsed since the BLE device power-up (Eddystone-TLM) |
s |
| sensor_sensitivity | Sensitivity of the MK PIR sensor
|
|
| single_alarm | Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| single_alarm_cnt | Number of the single press alarms of the connected MOKO Button device |
|
| tag_id | Tag id of the BLE device (BXP-Tag) |
|
| temperature | Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button) |
°C |
| timezone | Time zone of the local time reported by the gateway |
h |
| tlm_version | Version of the telemetry frame of the BLE device (Eddystone-TLM) |
|
| trigger_count | Number of the triggers of the BLE device (BXP-Button) |
|
| trigger_status | Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered |
|
| tx_power | Transmission power of the BLE device |
dBm |
| type | Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof |
|
| type_code | Code of the advertising data type of the BLE device
|
|
| uploaded_packets | Number of the buffered packets uploaded by the gateway |
|
| url | URL advertised by the BLE device (Eddystone-URL) |
|
| user_data | User data of the BLE device (MK TOF) |
|
| uuid | UUID of the BLE device (iBeacon) |
|
| acc | Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On |
|
| acc | Vehicle ACC (ignition) status detected by the gateway 0: Off 1: On |
|
| acc_status | Accelerometer sensor status of the BLE device (BXP-Tag) |
|
| acc_status | Accelerometer sensor status of the BLE device (BXP-Tag) |
|
| adv_cnt | Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM) |
|
| adv_cnt | Number of the advertising packets sent by the BLE device since power-up (Eddystone-TLM) |
|
| adv_data | Raw advertising data of the BLE device |
|
| adv_data | Raw advertising data of the BLE device |
|
| adv_interval | Interval of sending adv_data |
ms |
| adv_interval | Interval of sending adv_data |
ms |
| adv_name | Asset Name |
|
| adv_name | Asset Name |
|
| axis_x | Acceleration along the X axis |
mg |
| axis_x | Acceleration along the X axis |
mg |
| axis_y | Acceleration along the Y axis |
mg |
| axis_y | Acceleration along the Y axis |
mg |
| axis_z | Acceleration along the Z axis |
mg |
| axis_z | Acceleration along the Z axis |
mg |
| batt_vol | Volume of Internal Battery |
mV |
| batt_vol | Volume of Internal Battery |
mV |
| ble_batt_vol | Battery voltage of the MOKO Button device the gateway is connected to |
mV |
| ble_batt_vol | Battery voltage of the MOKO Button device the gateway is connected to |
mV |
| ble_company | Company name of the connected MOKO Button device |
|
| ble_company | Company name of the connected MOKO Button device |
|
| ble_dfu_pct | Firmware upgrade progress of the connected MOKO Button device |
% |
| ble_dfu_pct | Firmware upgrade progress of the connected MOKO Button device |
% |
| ble_dfu_result | Firmware upgrade result of the connected MOKO Button device
|
|
| ble_dfu_result | Firmware upgrade result of the connected MOKO Button device
|
|
| ble_disconnect_rsn | Reason of the disconnection from the MOKO Button device
|
|
| ble_disconnect_rsn | Reason of the disconnection from the MOKO Button device
|
|
| ble_firmware_ver | Firmware version of the connected MOKO Button device |
|
| ble_firmware_ver | Firmware version of the connected MOKO Button device |
|
| ble_hardware_ver | Hardware version of the connected MOKO Button device |
|
| ble_hardware_ver | Hardware version of the connected MOKO Button device |
|
| ble_mac | Mac of the MOKO Button device the gateway is connected to |
|
| ble_mac | Mac of the MOKO Button device the gateway is connected to |
|
| ble_product_model | Product model of the connected MOKO Button device |
|
| ble_product_model | Product model of the connected MOKO Button device |
|
| ble_result | Result code of the command sent to the MOKO Button device Connection result:
Result of the other commands:
|
|
| ble_result | Result code of the command sent to the MOKO Button device Connection result:
Result of the other commands:
|
|
| ble_software_ver | Software version of the connected MOKO Button device |
|
| ble_software_ver | Software version of the connected MOKO Button device |
|
| cell_id | Cell ID (CI) of the base station, LBS positioning data |
|
| cell_id | Cell ID (CI) of the base station, LBS positioning data |
|
| cert_result | MQTT SSL certificate download result
|
|
| cert_result | MQTT SSL certificate download result
|
|
| connectable | Status of the BLE device 0: Not Connectable 1: Connectable |
|
| connectable | Status of the BLE device 0: Not Connectable 1: Connectable |
|
| csq | Cellular signal quality of the gateway, 0-31 |
|
| csq | Cellular signal quality of the gateway, 0-31 |
|
| data_block_1 | The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_1 | The 1st raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_2 | The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_2 | The 2nd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_3 | The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_3 | The 3rd raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_4 | The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_4 | The 4th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_5 | The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_5 | The 5th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_6 | The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_6 | The 6th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_7 | The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_7 | The 7th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_8 | The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_8 | The 8th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_9 | The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_9 | The 9th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_10 | The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| data_block_10 | The 10th raw data block of the advertising packet of an unrecognized (other) BLE device type. The data blocks to upload are configured by the 0X109B command |
|
| delay_response_status | Delay response status of the MK PIR device
|
|
| delay_response_status | Delay response status of the MK PIR device
|
|
| detection_status | Motion detection status of the MK PIR sensor
|
|
| detection_status | Motion detection status of the MK PIR sensor
|
|
| device_id | Device id of the BLE device (BXP-Button) |
|
| device_id | Device id of the BLE device (BXP-Button) |
|
| device_name | Name of the BLE device (BXP-Button, BXP-Tag) |
|
| device_name | Name of the BLE device (BXP-Button, BXP-Tag) |
|
| door_status | Current status of the door sensor 0: Closed 1: Open |
|
| door_status | Current status of the door sensor 0: Closed 1: Open |
|
| double_alarm | Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| double_alarm | Double press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| double_alarm_cnt | Number of the double press alarms of the connected MOKO Button device |
|
| double_alarm_cnt | Number of the double press alarms of the connected MOKO Button device |
|
| factory_reset | Set to 1 when the gateway is restored to the factory settings by the physical button |
|
| factory_reset | Set to 1 when the gateway is restored to the factory settings by the physical button |
|
| firmware_type | Firmware type of the BLE device (BXP-Button) |
|
| firmware_type | Firmware type of the BLE device (BXP-Button) |
|
| firmware_ver | Firmware version of the BLE device |
|
| firmware_ver | Firmware version of the BLE device |
|
| fix_mode | Positioning mode used for the reported fix
|
|
| fix_mode | Positioning mode used for the reported fix
|
|
| fix_result | Result of the positioning attempt
|
|
| fix_result | Result of the positioning attempt
|
|
| frame_type | Advertising frame type of the BLE device (BXP-Button)
|
|
| frame_type | Advertising frame type of the BLE device (BXP-Button)
|
|
| full_scale | Full-scale range of the accelerometer of the BLE device |
g |
| full_scale | Full-scale range of the accelerometer of the BLE device |
g |
| hall_status | Hall sensor status of the BLE device (BXP-Tag) |
|
| hall_status | Hall sensor status of the BLE device (BXP-Tag) |
|
| hall_trigger_cnt | Number of the hall sensor trigger events of the BLE device (BXP-Tag) |
|
| hall_trigger_cnt | Number of the hall sensor trigger events of the BLE device (BXP-Tag) |
|
| have_acc_sensor | Status parameter that shows if the accelerometer sensor is equipped |
|
| have_acc_sensor | Status parameter that shows if the accelerometer sensor is equipped |
|
| have_door_sensor | Status parameter that shows if the hall door sensor is connected |
|
| have_door_sensor | Status parameter that shows if the hall door sensor is connected |
|
| have_light_sensor | Status parameter that shows if the light sensor is connected |
|
| have_light_sensor | Status parameter that shows if the light sensor is connected |
|
| humidity | Humidity measured by the BLE device (BXP-TH) |
% |
| humidity | Humidity measured by the BLE device (BXP-TH) |
% |
| imei | IMEI of the gateway cellular module |
|
| imei | IMEI of the gateway cellular module |
|
| inactivity_alarm | Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| inactivity_alarm | Abnormal inactivity alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| instance | Instance of the BLE device (Eddystone-UID) |
|
| instance | Instance of the BLE device (Eddystone-UID) |
|
| lac | Location area code (LAC/TAC) of the base station, LBS positioning data |
|
| lac | Location area code (LAC/TAC) of the base station, LBS positioning data |
|
| light_sensor_status | Current status of the light sensor 1: Activated |
|
| light_sensor_status | Current status of the light sensor 1: Activated |
|
| long_alarm | Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| long_alarm | Long press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| long_alarm_cnt | Number of the long press alarms of the connected MOKO Button device |
|
| long_alarm_cnt | Number of the long press alarms of the connected MOKO Button device |
|
| low_batt_alarm | Set to 1 when the gateway battery voltage drops below the configured threshold |
|
| low_batt_alarm | Set to 1 when the gateway battery voltage drops below the configured threshold |
|
| mac | Mac of the connected BLE Device |
|
| mac | Mac of the connected BLE Device |
|
| major | Major value of the BLE device (iBeacon, MK PIR) |
|
| major | Major value of the BLE device (iBeacon, MK PIR) |
|
| mfg_code | Manufacturer vendor code of the BLE device (MK TOF) |
|
| mfg_code | Manufacturer vendor code of the BLE device (MK TOF) |
|
| minor | Minor value of the BLE device (iBeacon, MK PIR) |
|
| minor | Minor value of the BLE device (iBeacon, MK PIR) |
|
| motion_threshold | Motion detection threshold of the accelerometer of the BLE device |
g |
| motion_threshold | Motion detection threshold of the accelerometer of the BLE device |
g |
| motion_trigger_cnt | Number of the motion trigger events of the BLE device (BXP-Tag) |
|
| motion_trigger_cnt | Number of the motion trigger events of the BLE device (BXP-Tag) |
|
| namespace | Namespace of the BLE device (Eddystone-UID) |
|
| namespace | Namespace of the BLE device (Eddystone-UID) |
|
| net_type | Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS |
|
| net_type | Cellular network type used by the gateway: NB-IOT, CAT.M or GPRS |
|
| ota_result | Result of the gateway firmware upgrade
|
|
| ota_result | Result of the gateway firmware upgrade
|
|
| passwd_verification | Shows if the BLE device requires password verification |
|
| passwd_verification | Shows if the BLE device requires password verification |
|
| pwr_disconnect_alarm | Set to 1 when the gateway detects that the external power is disconnected |
|
| pwr_disconnect_alarm | Set to 1 when the gateway detects that the external power is disconnected |
|
| ranging_data | Ranging data of the BLE device, the reference signal strength used for the distance calculation |
dBm |
| ranging_data | Ranging data of the BLE device, the reference signal strength used for the distance calculation |
dBm |
| ranging_distance | Distance measured by the BLE device (MK TOF) |
mm |
| ranging_distance | Distance measured by the BLE device (MK TOF) |
mm |
| remaining_packets | Number of the buffered packets left to upload |
|
| remaining_packets | Number of the buffered packets left to upload |
|
| rsp_data | Raw scan response data of the BLE device |
|
| rsp_data | Raw scan response data of the BLE device |
|
| rssi | Signal Strength of the BLE device |
dBm |
| rssi | Signal Strength of the BLE device |
dBm |
| rssi_0m | Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL) |
dBm |
| rssi_0m | Signal strength of the BLE device measured at 0 m (Eddystone-UID, Eddystone-URL) |
dBm |
| rssi_1m | Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR) |
dBm |
| rssi_1m | Signal strength of the BLE device measured at 1 m (iBeacon, MK PIR) |
dBm |
| sampling_rate | Sampling rate of the accelerometer of the BLE device (BXP-ACC) |
Hz |
| sampling_rate | Sampling rate of the accelerometer of the BLE device (BXP-ACC) |
Hz |
| sec_cnt | Time elapsed since the BLE device power-up (Eddystone-TLM) |
s |
| sec_cnt | Time elapsed since the BLE device power-up (Eddystone-TLM) |
s |
| sensor_sensitivity | Sensitivity of the MK PIR sensor
|
|
| sensor_sensitivity | Sensitivity of the MK PIR sensor
|
|
| single_alarm | Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| single_alarm | Single press alarm status of the connected MOKO Button device 0: Not triggered 1: Triggered |
|
| single_alarm_cnt | Number of the single press alarms of the connected MOKO Button device |
|
| single_alarm_cnt | Number of the single press alarms of the connected MOKO Button device |
|
| tag_id | Tag id of the BLE device (BXP-Tag) |
|
| tag_id | Tag id of the BLE device (BXP-Tag) |
|
| temperature | Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button) |
°C |
| temperature | Temperature measured by the BLE device (Eddystone-TLM, BXP-TH, BXP-Button) |
°C |
| timezone | Time zone of the local time reported by the gateway |
h |
| timezone | Time zone of the local time reported by the gateway |
h |
| tlm_version | Version of the telemetry frame of the BLE device (Eddystone-TLM) |
|
| tlm_version | Version of the telemetry frame of the BLE device (Eddystone-TLM) |
|
| trigger_count | Number of the triggers of the BLE device (BXP-Button) |
|
| trigger_count | Number of the triggers of the BLE device (BXP-Button) |
|
| trigger_status | Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered |
|
| trigger_status | Trigger status of the BLE device (BXP-Button) 0: Not triggered 1: Triggered |
|
| tx_power | Transmission power of the BLE device |
dBm |
| tx_power | Transmission power of the BLE device |
dBm |
| type | Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof |
|
| type | Name of the advertising data type of the BLE device: ibeacon, eddystone-uid, eddystone-url, eddystone-tlm, bxp-devinfo, bxp-acc, bxp-th, bxp-button, bxp-tag, pir, other or tof |
|
| type_code | Code of the advertising data type of the BLE device
|
|
| type_code | Code of the advertising data type of the BLE device
|
|
| uploaded_packets | Number of the buffered packets uploaded by the gateway |
|
| url | URL advertised by the BLE device (Eddystone-URL) |
|
| user_data | User data of the BLE device (MK TOF) |
|
| uuid | UUID of the BLE device (iBeacon) |
|
| uploaded_packets | Number of the buffered packets uploaded by the gateway |
|
| url | URL advertised by the BLE device (Eddystone-URL) |
|
| user_data | User data of the BLE device (MK TOF) |
|
| uuid | UUID of the BLE device (iBeacon) |
