sf_vers |
Software version of the hardware
|
|
fw_vers |
Firmware version of the hardware
|
|
platform |
Platform version of the hardware
|
|
hw_vers |
Hardware version
|
|
acc_on |
Ignition ON Upload Interval
|
seconds |
acc_off |
Ignition OFF Upload Interval
|
seconds |
angle |
Angle Upload Interval
|
degrees |
distance |
Distance upload interval
|
m |
gps_data |
Bitwise variable, in which each bit means following:
- Bit7=0, realtime data; Bit7=1, history data
- Bit6=0, LBS data; Bit6=1, GNSS data
- Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode
- Bit4~Bit0, locked satellite count
|
|
speed_alarm |
Over speed alarm setting
|
km\h |
gsensor |
Bitwise variable in which each bit means following: - Bit7~Bit4, total 16 different gsensor sensitivity for move.
- Bit3~Bit0, show 4 managers status (set or not)
- Value=1, manger is set; Value=0, manager is null
|
|
heartbeat_int |
Sending interval of heartbeat package
|
minutes |
relay |
Relay status, which is bitwise variable - Bit7 (command type received):
- 0: device received the engine recover command
- 1: device received the engine cut command
- Bit6 (engine cut execution status):
- 0: engine cut failed because gps not fix or speed more than 20 km\h
- 1: engine cut ok
- Bit 5 & Bit4 (rly mode):
- 00: rlymode = 0
- 10: rlymode = 1
- 01: rlymode = 2
- 11: rlymode = 3~255
- Bit3~Bit 0 (buld in alarm SMS language):
- 0: Chinese
- 1: English
- 2: French
- 3: Spanish
- 4: German
- 5: Portuguese
- 6: Arabic
- 7: Indonesian
- 8: Russain
- 9: Turkish
|
|
drag_alarm |
Bitwise variable, each byte means following: 1.Bit15~Bit0. The range is 0~65535 2. Value(Bit15~Bit0)=0, the drag alarm is disabled 3. Once the alarm is set and enabled, when device detected the ignition status changed from ON to OFF, the alarm will automatically become effective.
|
|
1wire_device_type |
Device Type indicates the type of the 1-wire device. It currently supports below 1-wire device types: 0: 1-Wire RFID Reader 1: iButton Reader 40: Temp Sensor 46: Temp & Humi Sensor
|
|
hdop |
Horizontal Dilution of Precision, is a metric in GPS that indicates the accuracy of your horizontal (latitude and longitude) position, based on the geometric arrangement of satellites in the sky |
|
I/O |
Input/output state. See Wialon documentation to calculate each i/o state
|
|
ext_pwr_volt |
External power voltage
|
V |
adcN |
Analog-to-Digital Converter value. N - is the number of ADC's channel
|
|
int_bat_volt |
Internal battery voltage
|
V |
device_battery_type |
Device battery type
|
|
device_int_temp |
Device internal temperature
|
|
battery |
Battery level
|
% |
speed |
The speed of a vehicle
|
|
jamming_detection_and_control_setting |
The value of jamming detection and control setting
|
|
alert_setting |
The value of alert setting |
|
network_proto_setting |
The value of network protocol setting Bit 7: TCP Bit 6: UDP Bit 5: MQTT Bits 3-2: IP Bits 2-1: Connection type:
- 00: Long connection
- 10: Long and short connection
- 01: Short connection
|
|
manager_phone_number_setting |
The value of manager phone number setting
|
|
ignition_off_upload_interval |
Ignition OFF Upload Interval (Second)
|
sec |
ignition_on_upload_interval |
Ignition ON Upload Interval (Second)
|
sec |
angle_upload_interval |
Upload interval when vehicle turns every certain degrees
Unit: Degrees Value range:
- Value=0, disabled
- Value=[15-180]
|
Degree |
distance_upload_interval |
Distance Upload Interval (Meter)
|
Meters |
network_signal |
Network signal strength
|
|
network_status |
Network status bitwise variable: Bit 7: SIM card status Bit 6: Network status Bit 4: PDP activation status Bits 3-0: Socket status
|
|
gps_status |
Bitwise variable in which each bit means following
Bit 7: Working status 0: GNSS not working 1: GNSS working
Bit 6: GPS whether enabled Bit 5: GLONASS whether enabled Bit 4: Galileo whether enabled Bit 3: Beidou whether enabled 0: disabled 1: enabled Bit 2: Whether the positioning was successful Bit 1: Whether the positioning point is a historical point |
|
|
relay_status |
Bitwise variable in which each bit means following
Bit 7: 0, device received the engine recover command 1, device received the engine cut command Bit 6: 0, enginee cut failed because gps not fix or speed more than 20KM/H 1, engine cut OK Bit 5 & Bit 4: value=00, rlymode=0; value=10, rlymode=1; value=01, rlymode=2; value=11, rlymode=3~255#;(3-255 unit is minute) |
|
|
device_status |
Bitwise variable: Bit 15: Ignition status Bit 14: Idle status Bit 13: External power connection status Bit 12: USB connection status Bit 11: Solar charging status Bit 10: Smart upload mode enabled
|
|
odometer |
The odometer value
|
meter |
towing_alarm_threshold |
Towing Alarm Threshold
Range: 0~65535 Unit is meter
|
meters |
fms#N |
FMS data value, #N - is a value number
|
|
speeding_threshold |
Speeding Threshold
|
km/h |
accdet_setting |
ACCDET Setting: 0 - off, 1- on
|
|
locktrack_sim_apn_setting |
LOCKTRACK/SIM/APN Setting
Bit 7: Locktrack setting status Bit 6: Locksim setting status Bit 5: Lockapn setting status
0=disabled, 1=enabled |
|
|
alert_sms_setting |
Alert SMS Setting. Send alert SMS 0x01 = Yes 0x00 = No
|
|
heartbeat_setting |
Heartbeat Setting Range: 0~65535 Unit: minute
|
minutes |
ign_source |
Ignition source identification:
- value=0, the ignition voltage is greater than 13.5.
- value=1, OBD reports 010A ignition after vibration.
- value=2, read the data change of OBD after vibration and ignition. value=3, after the voltage value is greater than the learned value, pull up the OBD and report the 010A ignition ((accdet=2))
- value=4, after the voltage value is greater than the learned voltage value, pull up the OBD and read the OBD data change ignition (accdet=2)
- Value=5, greater than the set voltage value to identify ignition.
- value=6, set vibration recognition ignition (accdet>0)
|
|
mileage_source |
Mileage source code
|
|
alarm_code |
Alarm code 0x**:
| 1. =1, Device removed alarm (triggered by back light sensor) (VS alarm 21) |
2. =2, Rear cover open alarm (VS alarm 22) |
3. =3, SOS alarm |
4. =4, Front light detected (triggered by front light sensor) (VS alarm 23) |
5. =5, Start falling alarm (VS alarm 24) |
6.=6, Low battery alarm (Vs alarm 7) |
7.=7, Battery recovered alarm |
8. =8, Device high temperature alarm (VS alarm 25) |
9. =9, Vibration start alarm (VS alarm 26) |
10. =10, Collision alarm (VS alarm 27) |
11. =11, Tilt start alarm (VS alarm 28) |
12. =12, USB cable connected alarm (VS alarm 13) |
13. =13, USB cable disconnected alarm |
14. =14, Enter geofence alarm (VS alarm 15) |
15. =15, Leave geofence alarm |
16. =16, Start moving alarm (VS alarm 17) |
17.=17, Stop moving alarm |
18.=18, Idle start alarm (VS alarm 19) |
19.=19, Idle stop alarm |
20.=20, Power on (via function button) |
21.=21, Device mounted alarm (triggered by back light sensor) |
22.=22, Rear cover close alarm |
23. =23, Front light disappear alarm |
24.=24, Stop falling |
25. =25, Device high temperature disappear |
26.=26, Vibration stop alarm |
27.=27, Collision stopped alarm |
28.=28, Tilt recovered alarm |
29.=29, Power off (via function button) |
30.=30. Device low temperature alarm (VS alarm 31) |
31.=31. Device low temperature disappear |
32.=32. short stop alarm |
66.=66. Jamming alarm |
67.=67. Jamming alarm disappear |
70.=70. high speed alarm |
71.=71. high speed alarm disappear |
72.=72. drag alarm |
74.=74. google alarm |
77.=77. drag stopped alarm |
78.=78. authorized alarm |
79.=79. unauthorized alarm |
|
|