GPS tracker PioneerX 101 | Integrated with Wialon

Features PioneerX 101:

2G
4G/LTE
Blackbox
BLE enabled
Built-in odometer

Supported in Wialon:

Accelerometer
ADC sensors
Remote management via GPRS
Digital sensors
Communication via TCP
Communication via UDP

The following data should also be added to PioneerX 101 unit properties section of Wialon GPS tracking software :

Device type:	PioneerX 101
Unique ID:	imei

Specify the following parameters in configuration software or configuration PioneerX 101 for use in Wialon Hosting :

Server port:

22709

32 units of PioneerX 101 device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
sf_vers	Software version of the hardware
fw_vers	Firmware version of the hardware
platform	Platform version of the hardware
hw_vers	Hardware version
acc_on	Ignition ON Upload Interval	seconds
acc_off	Ignition OFF Upload Interval	seconds
angle	Angle Upload Interval	degrees
distance	Distance upload interval	m
gps_data	Bitwise variable, in which each bit means following: Bit7=0, realtime data; Bit7=1, history data Bit6=0, LBS data; Bit6=1, GNSS data Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode Bit4~Bit0, locked satellite count
speed_alarm	Over speed alarm setting	km\h
gsensor	Bitwise variable in which each bit means following: Bit7~Bit4, total 16 different gsensor sensitivity for move. Bit3~Bit0, show 4 managers status (set or not) Value=1, manger is set; Value=0, manager is null
heartbeat_int	Sending interval of heartbeat package	minutes
relay	Relay status, which is bitwise variable Bit7 (command type received): 0: device received the engine recover command 1: device received the engine cut command Bit6 (engine cut execution status): 0: engine cut failed because gps not fix or speed more than 20 km\h 1: engine cut ok Bit 5 & Bit4 (rly mode): 00: rlymode = 0 10: rlymode = 1 01: rlymode = 2 11: rlymode = 3~255 Bit3~Bit 0 (buld in alarm SMS language): 0: Chinese 1: English 2: French 3: Spanish 4: German 5: Portuguese 6: Arabic 7: Indonesian 8: Russain 9: Turkish
drag_alarm	Bitwise variable, each byte means following: 1.Bit15~Bit0. The range is 0~65535 2. Value(Bit15~Bit0)=0, the drag alarm is disabled 3. Once the alarm is set and enabled, when device detected the ignition status changed from ON to OFF, the alarm will automatically become effective.

Parameter name

Description

Units

sf_vers

Software version of the hardware

fw_vers

Firmware version of the hardware

platform

Platform version of the hardware

hw_vers

Hardware version

acc_on

Ignition ON Upload Interval

seconds

acc_off

Ignition OFF Upload Interval

seconds

angle

Angle Upload Interval

degrees

distance

Distance upload interval

gps_data

Bitwise variable, in which each bit means following:

Bit7=0, realtime data; Bit7=1, history data
Bit6=0, LBS data; Bit6=1, GNSS data
Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode
Bit4~Bit0, locked satellite count

speed_alarm

Over speed alarm setting

km\h

gsensor

Bitwise variable in which each bit means following:

Bit7~Bit4, total 16 different gsensor sensitivity for move.
Bit3~Bit0, show 4 managers status (set or not)
Value=1, manger is set; Value=0, manager is null

heartbeat_int

Sending interval of heartbeat package

minutes

relay

Relay status, which is bitwise variable

Bit7 (command type received):
- 0: device received the engine recover command
- 1: device received the engine cut command

Bit6 (engine cut execution status):
- 0: engine cut failed because gps not fix or speed more than 20 km\h
- 1: engine cut ok
Bit 5 & Bit4 (rly mode):
- 00: rlymode = 0
- 10: rlymode = 1
- 01: rlymode = 2
- 11: rlymode = 3~255
Bit3~Bit 0 (buld in alarm SMS language):
- 0: Chinese
- 1: English
- 2: French
- 3: Spanish
- 4: German
- 5: Portuguese
- 6: Arabic
- 7: Indonesian
- 8: Russain
- 9: Turkish

drag_alarm

Bitwise variable, each byte means following:

1.Bit15~Bit0. The range is 0~65535
2. Value(Bit15~Bit0)=0, the drag alarm is disabled
3. Once the alarm is set and enabled, when device detected the ignition status changed from ON to OFF, the alarm will automatically become effective.

Fill out a request form to get started with Wialon