Topflytech Pioneerx 100

Software version of the hardware

Firmware version of the hardware

Platform version of the hardware

Hardware version

Ignition ON Upload Interval

Ignition OFF Upload Interval

Angle Upload Interval

Distance upload interval

Bitwise variable, in which each bit means following:

1. Bit7=0, realtime data; Bit7=1, history data
2. Bit6=0, LBS data; Bit6=1, GNSS data
3. Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode
4. Bit4~Bit0, locked satellite count

Over speed alarm setting

Bitwise variable in which each bit means following:

1. Bit7~Bit4, total 16 different gsensor sensitivity for move.
2. Bit3~Bit0, show 4 managers status (set or not)
3. Value=1, manger is set; Value=0, manager is null

Sending interval of heartbeat package

Relay status, which is bitwise variable

• Bit7 (command type received):
  • 0: device received the engine recover command
  • 1: device received the engine cut command

• Bit6 (engine cut execution status):
  • 0: engine cut failed because gps not fix or speed more than 20 km\h
  • 1: engine cut ok
• Bit 5 & Bit4 (rly mode):
  • 00: rlymode = 0
  • 10: rlymode = 1
  • 01: rlymode = 2
  • 11: rlymode = 3~255
• Bit3~Bit 0 (buld in alarm SMS language):
  • 0: Chinese
  • 1: English
  • 2: French
  • 3: Spanish
  • 4: German
  • 5: Portuguese
  • 6: Arabic
  • 7: Indonesian
  • 8: Russain
  • 9: Turkish
    

Bitwise variable, each byte means following:

1.Bit15~Bit0. The range is 0~65535
2. Value(Bit15~Bit0)=0, the drag alarm is disabled
3. Once the alarm is set and enabled, when device detected the ignition status changed from ON to OFF, the alarm will automatically become effective.

Device Type indicates the type of the 1-wire device. It currently supports below 1-wire device types:

0: 1-Wire RFID Reader
1: iButton Reader
40: Temp Sensor
46: Temp & Humi Sensor

Input/output state. See Wialon documentation to calculate each i/o state

External power voltage

Analog-to-Digital Converter value. N - is the number of ADC's channel

Internal battery voltage

Device battery type

Device internal temperature

Battery level

The speed of a vehicle

The value of jamming detection and control setting

The value of network protocol setting

Bit 7: TCP
Bit 6: UDP
Bit 5: MQTT
Bits 3-2: IP
Bits 2-1: Connection type:

• 00: Long connection
• 10: Long and short connection
• 01: Short connection

The value of manager phone number setting

Ignition OFF
Upload Interval
(Second)

Ignition ON
Upload Interval
(Second)

Upload interval when vehicle turns every certain degrees

Unit: Degrees
Value range:

• Value=0, disabled
• Value=[15-180]

Distance Upload Interval
(Meter)

Network signal strength

Network status bitwise variable:

Bit 7: SIM card status
Bit 6: Network status
Bit 4: PDP activation status
Bits 3-0: Socket status

Bitwise variable in which each bit means following

Bitwise variable in which each bit means following

Bitwise variable:

Bit 15: Ignition status
Bit 14: Idle status
Bit 13: External power connection status
Bit 12: USB connection status
Bit 11: Solar charging status
Bit 10: Smart upload mode enabled

The odometer value

Towing Alarm Threshold

Range: 0~65535
Unit is meter

FMS data value, #N - is a value number

Speeding Threshold

ACCDET Setting: 0 - off, 1- on

LOCKTRACK/SIM/APN Setting

Alert SMS Setting. Send alert SMS
0x01 = Yes
0x00 = No

Heartbeat Setting

Range: 0~65535
Unit: minute

Ignition source identification:

• value=0, the ignition voltage is greater than 13.5.
• value=1, OBD reports 010A ignition after vibration.
• value=2, read the data change of OBD after vibration and ignition. value=3, after the voltage value is greater than the learned value, pull up the OBD and report the 010A ignition ((accdet=2))
• value=4, after the voltage value is greater than the learned voltage value, pull up the OBD and read the OBD data change ignition (accdet=2)
• Value=5, greater than the set voltage value to identify ignition.
• value=6, set vibration recognition ignition (accdet>0)

Mileage source code

Alarm code 0x**: