IoTLink Shadow

IoTLink Shadow
Discusión en el foro

Cantidad de unidades

0
En línea
2
Total

Para que el sistema de rastreo Wialon identifique los datos de IoTLink Shadow en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo: IoTLink Shadow
ID único: custom

Indique los siguientes parámetros en el programa de configuración o en la configuración IoTLink Shadow para utilizarlos en Wialon Hosting :

Puerto del servidor: 22730

En el centro de servicio Wialon se utilizan 2 unidades IoTLink Shadow — es 0% de la cantidad total de dispositivos Rastreador de activos conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro Descripción Unidades de medida
destination The selected drive destination
drv Driving state (0 = Stopped, 1 = Driving)
eng Engine state (0 = Off, 1 = On)
event_code Event code
event_descr Event description
fix_type The GPS fix type for the current location (2D / 3D)
fw_ver The unit's firmware version
gssn The current average signal level of visible satellites
gss The average GPS satellite signal level
ibutton The currently attached Dallas iButton
ign Ignition state
immobilizer The immobilizer armed state (0 = Disarmed, 1 = Armed)
jam Jamming detection state (0 = Not jammed, 1 = Jammed)
odometer Current odometer value
paramN Extra parameter (N - number of parameter)
pwr_ext Vehicle battery voltage V
pwr_int Backup battery voltage V
report_reason Location report reason
satn The current number of visible satellites
sat The number of visible GPS satellites at the time the location was received
serial_num The unit's factory serial number
tempN_state Temperature sensor N state
tempN Temperature sensor N value
efuel_event Fuel message type
efuel_current Current fuel value exist in car L
efuel_tank_size Car's fuel tank size
efuel_current_prct Percentage fuel level exist in car %
efuel_value Current fuel litters or percentage
grmn_connected

Garmin connection status: 0 = disconnected, 1 = connected.
Parameter appears when connection status is changed

esafe_msg_type

Message type from eSafe:
137 - Maneuver notification, will be transmitted as Drive rule occurred if enabled
143 - Accident notification, will be transmitted as Accident detected if enabled
144 - Drive status changed
145 - Too many events
146 - Bad installation
147 - Possible accident notification

esafe_maneuv_type

The eSafe maneuver type:
1 - Acceleration
2 - Breaking
3 - Left turn
4 - Right turn
5 - Wide left turn
6 - Wide right turn
7 - Left turn while decelerating
8 - Left turn while accelerating
9 - Wide left turn while decelerating
10 - Wide left turn while accelerating
11 - Right turn while decelerating
12 - Right turn while accelerating
13 - Wide right turn while decelerating
14 - Wide right turn while accelerating
15 - Traffic circle
16 - Lane change
17 - Overtaking
18 - Speed bump
19 - Start of off-road driving
20 - End of off-road driving

esafe_maneuv_level

The eSafe maneuver level:
1 - Low
2 - Medium
3 - High

esafe_maneuv_dur The eSafe maneuver duration ms
esafe_force_x The eSafe maximum g force detected in the X axis g
esafe_force_y The eSafe maximum g force detected in the Y axis g
esafe_force_z The eSafe maximum g force detected in the Z axis g
esafe_accident_direct

The eSafe accident directions:
1 - Front
2 - Front left
3 - Front right
4 - Back
5 - Back left
6 - Back right
7 - Left
8 - Right
9 - Vehicle rolled over

esafe_driver_state

The eSafe driver state:
0 - Normal
1 - Aggressive
2 - Dangerous

esafe_aggres_maneuvers The eSafe total number of aggressive maneuvers
esafe_danger_maneuvers The eSafe total number of dangerous maneuvers
esafe_num_maneuvers The eSafe total number of maneuvers
top_speedN The top speed with of speed limit rule number N km/h
top_speed_tmN The number of seconds the vehicle was above the speed limit with number N sec
nt Network technology
ccn The active cellular antenna's assigned channel number
ti# Sensor ID, # - number
cfl This field will contain the percentage of the fuel.

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Paso 1
Paso 2
Paso 3
Nombre de pila*
Apellido*
Compañía*
Email*
Teléfono