| pwr_ext |
Voltage level |
V |
| gsm |
GSM Signal Strength |
|
| imei |
imei number |
|
| imsi |
imsi number |
|
| iccid |
iccid number |
|
| time |
Time stamp |
|
| sats |
Number of satellites |
|
| visible_sats |
Visible satellites |
|
| sat#_signal_strength |
Satellites signal strength, where # - number |
|
| mcc |
LBS Main Cell Tower, mcc |
|
| mnc |
LBS Main Cell Tower, mnc |
|
| lac |
LBS Main Cell Tower, lac |
|
| cell_id |
LBS Main Cell Tower, cell_id |
|
| rssi |
LBS Main Cell Tower, rssi |
|
| lac# |
LBS Auxiliary Cell Tower, lac, where # - number |
|
| cell_id# |
LBS Auxiliary Cell Tower, cell_idm, where # - number |
|
| rssi# |
LBS Auxiliary Cell Tower, rssi, where # - number |
|
| gsm_signal_csq |
GSM Signal CSQ |
|
| voltage |
Built-in battery
voltage
0: No Power (shutdown)
1: Extremely Low Battery
2: Very Low Battery (Low Battery Alarm)
3: Low Battery (can be used normally)
4: Medium
5: High
6: Full
|
|
| hdop |
HDOP |
|
| sequence_num |
Sequence Number |
|
| inputs |
Input’s Status, Bit 1-4: Door button status (1/0 Door Open/Close), Bit 5-8: Tamper button status (1/0 Removal/Installation) 0xff: Failed to get button status |
|
| boot_reason |
Boot Reason
|
|
| mileage |
Mileage statistics |
|
| real_time_mode# |
Real time current mode, where # - number |
|
| static_parameter_mode# |
Static mode parameter, where # - number |
|
| is_geofence_rectangular# |
Circular o rectangular, 0 is circular, 1 is rectangular, where # - id |
|
| is_geofence_exit# |
Enter or Exit geofence, 1 is enter, 2 is exit, where # - id |
|
| status_code |
Report status: Status code
0x00 Upload in fixed time interval
0x14 Enter Geofence
0x15 Exit Geofence
0x1A Battery low power
0x1B Overspeed
|
|
| status_trig_time1 |
Report status: Trigger time |
|
| status_reg_content |
Report status: Trigger content |
|
| gps_time_status |
GPS is Real Time or Reupload |
|
| alm1 |
Alarm Bit 1 |
|
| alm2 |
Alarm Bit 2 |
|
| alm3 |
Alarm Bit 3 |
|
| sta1 |
Status Bit 1 |
|
| dyd |
Fuel/Electricity Cutoff Status |
|
| sos_num# |
SOS number, where # - number |
|
| center_num |
Centre number |
|
| fence |
GeoFence |
|
| door |
Door status |
|
| cit |
Content of Terminal Information (heartbeat msg) |
|
| alarm |
0x00: Normal 0x01: SOS alert 0x02: Power cut alert 0x03: Vibrating alert 0x04: Entered fence alert 0x05: Left fence alert 0x06: Speed alert 0x09: Tow/theft alert 0x0A: Entered GPS blind spot alert 0x0B: Left GPS blind spot alert 0x0C: Powered on alert 0x0D: GPS first fix alert 0x0E: Low external battery alert 0x0F: External battery low voltage protection alert 0x10: SIM changed alert 0x11: Powered off alert 0x12: Airplane mode on following external battery low voltage protection 0x13: Tamper alert 0x14: Door alert 0x15: Powered off due to low battery 0x16: Sound-control alert 0x17: Rogue base station detected alert 0x18: Cover removed alert 0x19: Low internal battery alert 0x20: Entered deep sleep mode alert 0x21: Reserved 0x22: Reserved 0x23: Fall alert 0x29: Harsh acceleration 0x2A: Sharp left cornering alert 0x2B: Sharp right cornering alert 0x2C: Collision alert 0x30: Harsh braking 0x32: Device unplugged alert 0x53:Oil Steal alarm 0x71:Refuel notice 0x77:ADC1 High voltage alarm 0x78:ADC1 Low voltage alarm 0xC5 Engine is already turned on 0xC6 Engine is already turned off 0xC7 Driver has been driving extendedly 0xC8 Extended driving of driver is already known 0XE6 INPUT1 is activated 0XE7 INPUT1 is deactivated 0XE8 INPUT2 is activated 0XE9 INPUT2 is deactivated 0xFF: ACC OFF 0xFE: ACC ON
|
|
| ubi_event_flg |
- 1: The end of the event
- 0: The event start packet and the Mid-packet
|
|
| ubi_on[UBI SERIAL NUMBER] |
1: Harsh acceleration. An event which triggered with a time longer than BS_Acce_Time, and a constant vertical acceleration speed higher than BS_Acce_Deta 2: Harsh brake. Accelerated speed of y-axis is less than BS_Dece_Deta 3: Harsh lane. switching The absolute value of the accelerated speed of x-axis is greater than BS_Lane_Deta and the orientation changes of the satellite positioning is less than BS_Lane_Angle 4: Sharp turn. The absolute value of the accelerated speed of X-axis is greater than BS_Turn_Deta and the orientation changes of the satellite positioning exceeds BS_Turn_Angle 5: Collision. The absolute value of the vehicle's acceleration is greater than BS_Coll_Deta and the vehicle's attitude angle change does not exceed BS_Coll_Angle 6: Vehicle stability. An event which triggered within a time longer than BS_Stab_Time, and a constant change of the navigation angle with the angle speed absolute value higher than BS_Stab_Rate. 7: Rollover. The pitch or roll angle changes by more than BS_Roll_Angle 8: Abnormal attitude. The maximum variable of pitch angle and roll angle is greater than SAtt_Min_Deta and less than SAtt_Max_Deta
|
|
| ubi_kind[UBI SERIAL NUMBER] |
- 0: None
- 1: UBI Event
- 2: UBI Alarm
|
|
| ubi_a[UBI SERIAL NUMBER] |
Context depends from the ubi_on[UBI SERIAL NUMBER] parameter
| №
|
UBI_ON
|
UBI_A
|
| 1
|
Harsh acceleration
|
BS_Acce_Deta
|
| 2
|
Harsh brake
|
BS_Dece_Deta
|
| 3
|
Harsh lane
|
BS_Lane_Deta
|
| 4
|
Sharp turn
|
BS_Turn_Deta
|
| 5
|
Collision
|
BS_Coll_Deta
|
| 6
|
Vehicle stability
|
BS_Stab_Rate
|
| 7
|
Rollover
|
BS_Roll_Angle
|
| 8
|
Abnormal attitude
|
SAtt_Min_Deta
|
|
|
| ubi_b[UBI SERIAL NUMBER] |
Context depends from the ubi_on[UBI SERIAL NUMBER] parameter
| №
|
UBI_ON
|
UBI_B
|
| 1
|
Harsh acceleration
|
BS_Acce_Time
|
| 2
|
Harsh brake
|
none
|
| 3
|
Harsh lane
|
BS_Lane_Angle
|
| 4
|
Sharp turn
|
BS_Turn_Angle
|
| 5
|
Collision
|
BS_Coll_Angle
|
| 6
|
Vehicle stability
|
BS_Stab_Time
|
| 7
|
Rollover
|
none
|
| 8
|
Abnormal attitude
|
SAtt_Max_Deta
|
|
|
| acc_x_d[UBI SERIAL NUMBER] |
Accelerated speed of x-axis
|
m/s^2 |
| acc_y_d[UBI SERIAL NUMBER] |
Accelerated speed of y-axis
|
m/s^2 |
| gyr_z_d[UBI SERIAL NUMBER] |
Angular velocity of z-axis
|
degree/s |
| pitch_ang[UBI SERIAL NUMBER] |
Vehicle pitch angle
|
degree |
| roll_ang[UBI SERIAL NUMBER] |
Vehicle roll angle
|
degree |
| yaw_ang[UBI SERIAL NUMBER] |
Vehicle orientation change angle
|
degree |
| car_spd[UBI SERIAL NUMBER] |
Vehicle speed
|
m/s |
| ins_flg[UBI SERIAL NUMBER] |
INS activated flag INS_Flag Physical significance
- Ins_Flag=0: to be initialized. Disable UBI
- Ins_Flag=1: INS activation step 1. Enable UBI
- Ins_Flag=2: INS activation step 2. Enable UBI
- Ins_Flag=3: INS activation step 3. Enable UBI
- Ins_Flag=4: INS activation completed. Enable UBI
|
|
| ubi_num[UBI SERIAL NUMBER] |
UBI Serial number. Has range in 0-30
|
|
| ubi_vld[UBI SERIAL NUMBER] |
UBI Valid flag 1: Valid 0: Invalid
|
|
| acc_t_d[UBI SERIAL NUMBER] |
Vehicle horizontal acceleration change rate
|
m/s |
| coll_t_h[UBI SERIAL NUMBER] |
Direction of the collision. Will be registrated only if the module version = 1
|
degree |
