GPS Padlock G-300 (New Protocol)

Fabricante: Shenzhen HHD Technology

Forum Discussion

Número de unidades

ON-LINE

TOTAL

Dynamic hosting units GPS Padlock G-300 (New Protocol)

Information
Parameters

Features GPS Padlock G-300 (New Protocol):

4G/LTE
Boîte à mémoire
BLE enabled
E-seal

Supported in Wialon:

Communication via TCP

The following data should also be added to GPS Padlock G-300 (New Protocol) unit properties section of Wialon GPS tracking software :

Device type:	GPS Padlock G-300 (New Protocol)
ID único:	serial

Specify the following parameters in configuration software or configuration GPS Padlock G-300 (New Protocol) for use in Wialon Hosting :

Porta do servidor:

22460

39 units of GPS Padlock G-300 (New Protocol) device type are connected to Wialon Data Center. This represents 0.03% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name

Description

Units

status_cmd_[CMD ID]

Status of the command if it was successful.
CMD ID — id of the parameter that was sent via command platform_cmd

odometer

Odometer of the vehicle

mileage

Total mileage of the vehicle

fuel_volume

Fuel tank capacity

m^3

tank_oil_volume

Tank oil volume

m^3

load_sens_id_[NUM]

ID of the load [NUM] sensor, up to 4 groups of load sensors

ad_blue_[NUM]

AD Blue value of the [NUM] sensor, corresponding to load_sens_id. Up to 4 groups of sensors

wifi_mac_[NUM]

Wi-fi MAC address of the [NUM] point. When the satellite positioning is invalid, the terminalactively uploads the current WIFI DATA to the platform for auxiliary positioning. The WIFI_MAC information does not exceed 10 groups

wifi_rssi_[NUM]

WiFi signal strength of the [NUM] point. When the satellite positioning is invalid, the terminalactively uploads the current WIFI DATA to the platform for auxiliary positioning. The WIFI_RSSI information does not exceed 10 groups

ble_mac_[NUM]

BLE MAC address of the [NUM] point. When the satellite positioning is invalid, the terminalactively uploads the current BLE DATA to the platform for auxiliary positioning. The BLE_MAC information does not exceed 10 groups

ble_rssi_[NUM]

BLE signal strength of the [NUM] point. When the satellite positioning is invalid, the terminalactively uploads the current BLE DATA to the platform for auxiliary positioning. The BLE_RSSI information does not exceed 10 groups

event_id

ID of the Event

event_type

Event Type:

0x00 — Normal event
0x01 — Alarm Event

slave_id_[NUM]

Lora save lock slave ID of [NUM] lock

slave_battery_[NUM]

Battery percentage of the [NUM] LORA lock

slave_sealed_[NUM]

Seal status of the [NUM] LORA lock.

0X30 — Unseal
0x31 — Seal

slave_phys_state_[NUM]

Physical state of the [NUM] LORA lock

0X31 — Bound
0x32 — Shackle closed
0x33 — Shackle opened
0x34 — Shell opened
0x35 — Communication timeout
0x36 - Shacle/Wire rope is cut;

slave_rssi_[NUM]

Wireless strength of [NUM] LORA lock signal

temp_hum_sens_id_[NUM]

Lora temperature and humidity sensor ID of [NUM] sensor

lora_pwr_int_[NUM]

Internal voltage of the [NUM] LORA sensor.

lora_real_tm_temp_[NUM]

Real time temperature of the [NUM] LORA sensor

°C

low_temp_alm_val_[NUM]

Minimum temperature which triggers alarm on [NUM] Lora sensor

°C

overtemp_alm_time_[NUM]

Maximum temperature which triggers alarm on [NUM] Lora sensor

°C

real_tm_overtemp_alm_stat_[NUM]

Continuous over temperature alarm time threshold of the LORA sensor

lora_real_tm_hum_[NUM]

Real time humidity of the [NUM] LORA sensor

low_hum_alm_val_[NUM]

Minimum humidity which triggers alarm on [NUM] Lora sensor

overhum_alm_time_[NUM]

Maximum humidity which triggers alarm on [NUM] Lora sensor

real_tm_overhum_alm_stat_[NUM]

continuous over humidity alarm time threshold of the LORA sensor

sens_rssi_[NUM]

signal strength of the [NUM] LORA sensor

keypad_passwd

Keypads unlock dynamic password (with P model support, such as G300P, the device will automatically generate random passwords after unlocking each time)

battery

Battery level

pwr_int

Battery voltage

csq_signal

Network CSQ Signal

sim_imsi

IMSI Code of the SIM Card. The upload is triggered when the network is reonnected

client_id

Client ID

term_upg_res

Terminal upgrade result: Upgrade result of the current version, for example, 0, G4-360_20220301 Upgrade result: 0 - The upgrade succeeds. 1 - The upgrade fails

hw_vers

hardware version information

sf_vers

Software version information

iccid

Terminal ICCID code

gnss_manufacturer

GNSS module manufacturer.

0X01 - 中科微
0x02 — U-BLOX;

bt_name

Bluetooth name of the device itself

bt_mac

Bluetooth MAC address of the chip itself

wifi_mac

Wifi mac address of the chip itself

status_flag

Bitwise parameter where each bit means

Bit	Status
0	0: ACC OFF; 1:ACC ON（Padlock products don’t need this ）
1	0: GPS invalid; 1: GPS valid
2	0: North Latitude; 1: South Latitude
3	0: East Longitude; 1: West Longitude
4	0: Long connection; 1: Short connection
5	0: GPS module OFF; 1: GPS module ON
6	Motion sensor(G-sensor) status 0: motion state; 1: static state
7	0: Travel switch closed 1: Travel switch opened
8	0: Hall sensor connected 1: Hall sensor disconnected
9-13	Reserved field
14	0：Unseal; 1: Seal;
15	0：Shackle opened; 1:Shackle closed;
16-17	00: No charging 01: Charging 10: Fully charged
18-19	00: default; 01:2G; 10:3G; 11:4G
20-21	0: default; 01: SIM 1; 10: SIM 2
22-23	00: Non; 01:WIFI; 10:RJ45
24-31	Reserved

event_content

The value depends on event_id parameter

Event ID	Event	Event Type	Event Content
0x0000	Shackle closed	0x00（Normal）	0x00（Default）
0x0001	Shackle opened	0x00（Normal）	0x00（Default）
0x0002	Close shackle auto sealed	0x00（Normal）	0x00（Default）
0x0003	Swipe IC card to seal successful	0x00（Normal）	8 digits card ID
0x0004	Swipe card to unseal successful	0x00（Normal）	8 digits card ID
0x0005	BLE seal successful	0x00（Normal）	APP_BLE user name or ID;
0x0006	BLE unseal successful	0x00（Normal）	APP_BLE user name or ID;
0x0007	Platform seal successful	0x00（Normal）	Platform user name or ID
0x0008	Platform unseal successful	0x00（Normal）	Platform user name or ID
0x0009	SMS seal successful	0x00（Normal）	SMS mobile phone number
0x000A	SMS unseal successful	0x00（Normal）	SMS mobile phone number
0x000B	Unregistered IC card seal fails	0x00（Normal）	8 digits card ID
0x000C	Unregistered IC card unseal fails	0x00（Normal）	8 digits card ID
0x000D	IC card seal fails due to outside of the area	0x01（Alarm）	8 digits card ID
0x000E	IC card unseal fails due to outside of the area	0x01（Alarm）	8 digits card ID
0x000F	Shackle been opened under sealing states	0x01（Alarm）	0x00:（Default）
0x0010	Device Shell was tampered/removed	0x01（Alarm）	0x00:（Default）
0x0011	Shackle /Wire rope been cut	0x01（Alarm）	0x00:（Default）
0x0012	Battery voltage low get offline	0x01（Alarm）	0x00:（Default）
0x0013	Too many incorrect passwords areentered	0x01(Alarm)	0x00:（Default）
0x0014	Auto seal due to after unsealing for long time shackle did not been pull out	0x00（Normal）	0x00:（Default）
0x0015	Short connection handstand activation online	0x00（Normal）	0x00:（Default）
0x0016	Short connection touch activates online	0x00（Normal）	0x00:（Default）
0x0017	User set low battery threshold alarm reminder	0x01(Alarm)	0x00:（Default）
0x0018	Motor got stuck during sealing	0x01(Alarm)	0x00:（Default）
0x0019	Motor got stuck during unsealing	0x01(Alarm)	0x00:（Default）
0x001A	GPS antenna open circuit	0x01(Alarm)	0x00:（Default）
0x001B	GPS antenna short circuit	0x01(Alarm)	0x00:（Default）
0x001C	MCU communication abnormal	0x01(Alarm)	0x00:（Default）
0x001D	Full charged	0x00（Normal）	0x00（Default）
0x001E	Disconnected charger	0x00（Normal）	0x00（Default）
0x001F	Connected charger	0x00（Normal）	0x00（Default）
0x0020	Device/Terminal shut down reminder	0x00（Normal）	0x00（Default）
0x0021	Motion wake up under short connection	0x00（Normal）	0x00（Default）
0x0022	Static passwords unlock events	0x00（Normal）	Static unlock password value; (usually 8 digits)
0x0023	APP reports BLE sealing	0x00（Normal）	APP_BLE username or ID;(Used when APP is connected to pure Bluetooth lock)
0x0024	APP reports BLE unsealing	0x00（Normal）	APP_BLE username or ID;(Used when APP is connected to pure Bluetooth lock)
0x0025	Business data changes	0x00（Normal）	0x00（Default）
0x0026	Dynamic passwords unlock events	0x00（Normal）	Dynamic unlock password value;(usually 8 digits)
0x0027	Emergency key unseal event	0x00（Normal）	0x00（Default）
0x0028	Emergency key seal event	0x00（Normal）	0x00（Default）
0x0029	Emergency physical key is not closed, sealing failure event	0x00（Normal）	0x00（Default）
0x002A	Scheduled unseal events	0x00（Normal）	0x00（Default）
0x002C	Handstand flip (180 degree rotate)	0x01（Alarm）	0x00（Default） This event is only applicable to the use of fixed equipment, such as: smart box, fixed lock, etc.
0x0030	Geo-Fence in invalid date swipe card, unseal failure	0x00（Normal）	8 digits card ID: Format: string
0x0031	Geo-Fence in invalid date swipe card, seal failure	0x00（Normal）	8 digits card ID: Format: string
0x0032	Geo-Fence in invalid time swipe card, unseal failure	0x00（Normal）	8 digits card ID: Format: string
0x0033	Geo-Fence in invalid time swipe card, seal failure	0x00（Normal）	8 digits card ID: Format: string
0x0048	Swipe unregister seal card fail in Geo-Fence	0x00（Normal）	8 digits card ID: Format: string
0x0049	Swipe unregister unseal card fail in Geo-Fence	0x00（Normal）	8 digits card ID: Format: string
0x004A	Swipe unseal card successful in Geo-Fence	0x00（Normal）	8 digits card ID: Format: string
0x004B	Swipe seal card successful in Geo-Fence	0x00（Normal）	8 digits card ID: Format: string
0x004C	Outside Geo-Fence swipe unseal card failure	0x00（Normal）	8 digits card ID: Format: string
0x004D	Outside Geo-Fence swipe seal card failure	0x00（Normal）	8 digits card ID: Format: string Password
0x0034	Geo-Fence invalid password, unseal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0035	Geo-Fence invalid password, seal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0036	Geo-Fence in invalid date password unseal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0037	Geo-Fence in invalid date password seal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0038	Geo-Fence in invalid time password unseal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0039	Geo-Fence in invalid time password seal failure	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x004E	Password unseal successful in Geo-Fence	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x004F	Password unseal failure in Geo-Fence	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0114	Password seal successful in Geo-Fence	0x00（Normal）	Unlock password value usually 8 digits. Format: String
0x0115	Password seal failure in Geo-Fence	0x00（Normal）	Unlock password value usually 8 digits.Format: String
0x003A	Geo-Fence invalid SMS, unseal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x003B	Geo-Fence invalid SMS, seal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x003C	Geo-Fence in invalid date SMS unseal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x003D	Geo-Fence in invalid date SMS seal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x003E	Geo-Fence in invalid time SMS unseal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x003F	Geo-Fence in invalid time SMS seal failure	0x00（Normal）	SMS mobile phone number. Format: String
0x0100	SMS seal successful in Geo-Fence	0x00（Normal）	SMS mobile phone number. Format: String
0x0101	SMS unseal successful in Geo-Fence	0x00（Normal）	SMS mobile phone number.Format: String
0x0102	SMS seal failure outside Geo-Fence	0x00（Normal）	SMS mobile phone number. Format: String
0x0103	SMS unseal failure outside Geo-Fence	0x00（Normal）	SMS mobile phone number. Format: String
0x0040	Geo-Fence invalid BLE, unseal failure	0x00（Normal）	Platform user name or ID Format: String
0x0041	Geo-Fence invalid BLE, seal failure	0x00（Normal）	Platform user name or ID Format: String
0x0042	Geo-Fence in invalid date BLE seal failure	0x00（Normal）	Platform user name or ID Format: String
0x0043	Geo-Fence in invalid time BLE unseal failure	0x00（Normal）	Platform user name or ID Format: String
0x0044	Geo-Fence in invalid time BLE seal failure	0x00（Normal）	Platform user name or ID Format: String
0x0045	Geo-Fence in invalid date BLE seal failure	0x00（Normal）	Platform user name or ID Format: String
0x0104	BLE seal successful in Geo-Fence	0x00（Normal）	Platform user name or ID Format: String
0x0105	BLE unseal successful in Geo-Fence	0x00（Normal）	Platform user name or ID Format: String
0x0106	BLE unseal failutre outside Geo-Fence	0x00（Normal）	Platform user name or ID Format: String
0x0107	BLE seal failutre outside Geo-Fence	0x00（Normal）	Platform user name or ID Format: String
0x0046	Geo-Fence in invalid date touch seal failure	0x00（Normal）	0x00（Default）
0x0047	Geo-Fence in invalid time touch sealc failure	0x00（Normal）	0x00（Default）
0x0112	Touch seal successful in Geo-Fence	0x00（Normal）	0x00（Default）
0x0113	Touch seal failure in Geo-Fence	0x00（Normal）	0x00（Default）
0x0051	Web remote access gateway to unseal sub-lock via LORA successfully	0x00（Normal）	Slave ID [6] + [Remote unseal operator information] Format: Slave ID [6]: Byte displayed in HEX hexadecimal format Remote operator info: String
0x0052	APP unsealed sub-lock via BLE	0x00（Normal）	Slave ID [6] + [APP operatorinformation] Slave ID [6]: Byte displayed in HEX hexadecimal format APP operator info: String
0x0053	APP access gateway through BLE tounseal sub-lock via LORA successfully	0x00（Normal）	Slave ID [6] + [APP operator information] Slave ID [6]: Byte displayed in HEX hexadecimal format APP operator info: String
0x0054	SMS remote access gateway to unseal sub-lock via LORA successfully	0x00（Normal）	Slave ID [6] + [ mobile phone number that sent SMS] Slave ID [6]: Byte displayed in HEX hexadecimal format Mobile phone number for sending SMS: String
0x0055	Sub-lock shackle closed, auto sealed	0x00（Normal）	Slave ID [6] Format: Byte displayed in HEX hexadecimal format
0x0056	Sub-lock shackle opened after unsealing	0x00（Normal）	Slave ID [6] Format: Byte displayed in HEX hexadecimal format
0x0057	Sub-lock shell was tampered	0x01（Alarm）	Slave ID [6]Format: Byte displayed in HEXhexadecimal format
0x0058	Sub-lock shackle was opened/cut in sealing state	0x01（Alarm）	Slave ID [6] Format: Byte displayed in HEX hexadecimal format
0x0059	Sub-lock communicate timeout	0x01（Alarm）	Slave ID [6] Format: Byte displayed in HEX hexadecimal format
0x005A	Sub-lock low battery alarm	0x01（Alarm）	Slave ID [6] Format: Byte displayed in HEX hexadecimal format
0x005B	Auto disabled LORA unsealing in moving sate	0x00（Normal）	0x00（device detects motion status and enables automatic sealing, so use 0x00）
0x005C	BLE parameter setting unsealed via LORA	0x00（Normal）	APP_BLE User Name or ID Format: String
0x005D	Web parameter setting sealed via LORA	0x00（Normal）	Platform User Name or ID Format: String
0x005E	Web parameter setting unsealed viaLORA	0x00（Normal）	Platform User Name or ID Format: String
0x005F	SMS setting sealed via LORA	0x00（Normal）	[ sent SMM Mobile phone number ];Format: String
0x0060	SMS setting unsealed via LORA	0x00（Normal）	[sent SMM Mobile phone number];
0x0061	Unsealed sub-lock by own registered card	0x00（Normal）	Slave ID [6] + card ID [8] Format: Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0062	Sealed sub-lock by own registered card	0x00（Normal）	Slave ID [6] + card ID [8] Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0063	Sub-lock swiped unregistered unseal card	0x00（Normal）	Slave ID [6] + card ID [8] Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0064	Sub-lock swiped unregistered seal card	0x00（Normal）	Slave ID [6] + card ID [8] Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0065	Card unsealed sub-lock through gateway	0x00（Normal）	Slave ID [6] + card ID [8] Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0066	Card sealed sub-lock through gateway	0x00（Normal）	Slave ID [6] + card ID [8] Slave ID [6]: Byte The display uses HEX hexadecimal Card ID [8]: String
0x0067	Web remote unsealed sub-lock through gateway via LORA	0x00（Normal）	Slave ID [6] + [Remote unseal operator information] Format: Slave ID [6]: Byte The display uses HEX hexadecimal Remote operator info : String
0x0068	APP BLE sealed sub-lock	0x00（Normal）	Slave ID [6] + [APP operator information] Format: Slave ID [6]: Byte The display uses HEX hexadecimal APP operator info : String
0x0069	APP BLE sealed sub-lock via gateway LORA	0x00（Normal）	Slave ID [6] + [APP operator information] Format: Slave ID [6]: Byte The display uses HEX hexadecimal APP operator info : String
0x006A	SMS remote sealed sub-lock via gateway LORA	0x00（Normal）	Slave ID [6] + [ mobile phone number that sent SMS] Format: Slave ID [6]: Byte The display uses HEX hexadecimal Mobile phone number for sending SMS: String
0x006B	BLE Parameter setting unsealed via LORA	0x00（Normal）	APP_BLE username or ID; Format: String
0x006C	Sub-lock shackle not open for a long time after unsealing, auto sealed	0x00（Normal）	Slave ID [6] Format: Byte The display uses HEX hexadecimal
0x0070	Temperature exceeded upper limit	0x01（Alarm）	Temperature and humidity device ID [6]Format: Byte The display uses HEXhexadecimal
0x0071	Temperature exceeded the lower limit alarm	0x01（Alarm）	Temperature and humidity device ID [6] Format: Byte The display uses HEX hexadecimal
0x0072	Humidity exceeded upper limit alarm	0x01（Alarm）	Temperature and humidity device ID [6] Format: Byte The display uses HEX hexadecimal
0x0073	Humidity exceeded lower limit alarm	0x01（Alarm）	Temperature and humidity device ID [6] Format: Byte The display uses HEX hexadecimal
0x0074	Timeout alarm event	0x01（Alarm）	Temperature and humidity device ID [6] Format: Byte The display uses HEX hexadecimal
0x0075	3-axis impact alarm event	0x01（Alarm）	Temperature and humidity device ID [6] Format: Byte The display uses HEX hexadecimal
0x0090	Firmware version reported event	0x00	Version number (Upload only after the device is reset and reboot) Format: String
0x00A0	Overspeed alarm	0x01（Alarm）	0x00(Default) If the speed exceeds the set threshold, report an over-speed alarm event. If the speed exceeds continuously or the speed returns to normal, report an over-speed alarm event within 5 minutes.
0x00A1	Overparking alarm	0x01（Alarm）	0x00(Default) 1) If the parking time exceeds the set threshold, only one event will be reported if the parking time is in a stationary state continuously. 2)Only after the movement is changed and the parking timeout threshold is reached again, the event reporting will be triggered again.

alarm_flag

Bitwise parameter where each bit means

Bit	Definition	Process Description
0	1：Shackle been pulled out (Under the sealing state)	-
1	1：Shell tampered/damaged alarm	-
2	1：Low battery alarm	-
3	1：MCU communicate abnormal alarm	-
4	1: Shackle / String cable been cut/ disconnected alarm	-
5	1：GPS antenna open circuit alarm	-
6	1：GPS antenna short circuit alarm	-
7	1: Motor is stuck during sealing	Only the version with photoelectric switch can support this function
8	1：Motor is stuck during unsealing	Only the version with photoelectric switch can support this function
9	1：Over-speed alarm	Kept until the alarm condition is cleared
10	1：Timeout parking alarm	Kept until the alarm condition is cleared
11	1：GNSS module failure	Kept until the alarm condition is cleared
12	1：Main power failure	Kept until the alarm condition is cleared
13-31	Reserved (default 0)	Reserved (default 0)

More devices from the manufacturer

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Junte-se à nossa associação global de especialistas em telemática. Ajude seus clientes a transformar seus negócios com soluções de IoT conectadas e análises profundas.

Solicite o Wialon na sua região

Obtenha uma solução de telemática dos nossos parceiros de confiança para melhorar as operações da sua frota, reduzir custos de manutenção e melhorar a gestão de combustível.

Preencha um formulário de solicitação para começar

PASSO 1

PASSO 2

PASSO 3

Primeiro nome*

Sobrenome*

Empresa*

E-mail*

Telefone

Eu concordo com o processamento de meus dados pessoais
Política de Privacidade

‹ › ×

Produtos

Produtos de nicho para tarefas específicas