Asset GPS tracker Orbcomm ST 9100 | Integrated with Wialon

Features Orbcomm ST 9100:

3G
4G/LTE
Boîte à mémoire
BLE enabled
Terminal satellite

The following data should also be added to Orbcomm ST 9100 unit properties section of Wialon GPS tracking software :

Device type:	Orbcomm ST 9100
ID único:	serial

Specify the following parameters in configuration software or configuration Orbcomm ST 9100 for use in Wialon Hosting :

Porta do servidor:

22061

112 units of Orbcomm ST 9100 device type are connected to Wialon Data Center. This represents 0.07% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
hardwareVariant	This field indicates the terminal type. 1 – IDP terminal All other values are reserved
bootLoaderMajor	The major version number of the installed boot loader
bootLoaderMinor	The minor version number of the installed boot loader
bootLoaderPatch	The patch level number of the installed boot loader
firmwareMajor	The major version number of the installed base firmware
firmwareMinor	The minor version number of the installed base firmwarer
firmwarePatch	The patch level number of the installed base firmware
uptime	The number of seconds the terminal has been in continuous operation since reset
timeOfDay	The current date and time, expressed as number of seconds since the epoch
LSFUptime	The number of seconds the Lua Services Framework has been running
powerSaveTime	The number of seconds the terminal has been in power save mode since reset
sin	The SIN
enabled	Whether the service is currently enabled
proplist	A list of properties for that service
time	The new date and time, expressed as number of seconds since the epoch
extPowerPresent	external power
batteryVoltage	voltage of battery
externalVoltage	external voltage
powerOnReason	power on reason
autoPowerOnConfig	auto power on config
success	success
error	error
batteryType	Type of battery
min	min
data	The data to be sent out
fix_type	fixType
port#_cfg	Config of port where #-number of port
port#_value	value of port where #-number of port
current_temp	currentTemperature
pwr_ext	inputPowerVoltage
dte_connected	DTEConnected
cmd_success	Whether the command was successfully executed
msg_sin	sin of msg
msg_min	min of msg
region_name	name of region
ignition	1 - ignition on 0 - ignition off
comm_channel	comm_channel
event_name	name of event
gprs_channel	gprs channel
digitalports	Bitmap of all current digital I/O states (1 = High): Bit 0 – Line 1 (LSb) ... Bit 17 – Line 18 Note: Line 13 is a virtual digital line tied to the terminal’s external power status (1 = powered externally)
gpsfixage	Specifies the GPS fix age in seconds relative to the EventTime. The value is capped at 1023 seconds. This field is populated only if the fix age is greater than five seconds.
inputvoltage	Specifies the terminal's input voltage in tenths of volts.	V
odometer	Provides an incremental GPS-based odometer in km (max 524,288 km).	km
sensorN	Specifies the current Sensor N value.

Parameter name

Description

Units

hardwareVariant

This field indicates the terminal type. 1 – IDP terminal All other values are reserved

bootLoaderMajor

The major version number of the installed boot loader

bootLoaderMinor

The minor version number of the installed boot loader

bootLoaderPatch

The patch level number of the installed boot loader

firmwareMajor

The major version number of the installed base firmware

firmwareMinor

The minor version number of the installed base firmwarer

firmwarePatch

The patch level number of the installed base firmware

uptime

The number of seconds the terminal has been in continuous operation since reset

timeOfDay

The current date and time, expressed as number of seconds since the epoch

LSFUptime

The number of seconds the Lua Services Framework has been running

powerSaveTime

The number of seconds the terminal has been in power save mode since reset

sin

The SIN

enabled

Whether the service is currently enabled

proplist

A list of properties for that service

time

The new date and time, expressed as number of seconds since the epoch

extPowerPresent

external power

batteryVoltage

voltage of battery

externalVoltage

external voltage

powerOnReason

power on reason

autoPowerOnConfig

auto power on config

success

error

batteryType

Type of battery

min

data

The data to be sent out

fix_type

fixType

port#_cfg

Config of port where #-number of port

port#_value

value of port where #-number of port

current_temp

currentTemperature

pwr_ext

inputPowerVoltage

dte_connected

DTEConnected

cmd_success

Whether the command was successfully executed

msg_sin

sin of msg

msg_min

min of msg

region_name

name of region

ignition

1 - ignition on
0 - ignition off

comm_channel

event_name

name of event

gprs_channel

gprs channel

digitalports

Bitmap of all current digital I/O states (1 = High):

Bit 0 – Line 1 (LSb)
...
Bit 17 – Line 18

Note: Line 13 is a virtual digital line tied to the terminal’s external power status (1 = powered externally)

gpsfixage

Specifies the GPS fix age in seconds relative to the EventTime. The value is capped at 1023 seconds. This field is populated only if the fix age is greater than five seconds.

inputvoltage

Specifies the terminal's input voltage in tenths of volts.

odometer

Provides an incremental GPS-based odometer in km (max 524,288 km).

sensorN

Specifies the current Sensor N value.

Preencha um formulário de solicitação para começar