DATECS

Fabricante: DATECS

Forum Discussion

Número de unidades

ON-LINE

133

TOTAL

Information
Parameters

The following data should also be added to DATECS unit properties section of Wialon GPS tracking software :

Device type:	DATECS
ID único:	serial

133 units of DATECS device type are connected to Wialon Data Center. This represents 0.01% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name

Description

Units

ib_serial

iButton serial number (16 hex symbols)

ib_alarm_control_mask

iButton alarm control mask. Define frequency for RTC alarm.
15 - Alarm once per second;
14 - Alarm when seconds match (once per minute);
12 - Alarm when minutes and seconds match (once every hour);
8 - Alarm when hours, minutes, and seconds match (once every day);
0 - Alarm when day, hours, minutes, and seconds match (once every week).
(from iButton register page.)

ib_alarm_time

time for RTC alarm. RTC alarm will happen every second/minute/day/week (according to ib_alarm_control_mask)
(from iButton register page.)

HH:MM:SS

ib_temp_alarm_treshold_low

Low temperature threshold, the device generates alarm when this temperature is reached.
(from iButton register page.)

ib_temp_alarm_treshold_high

High temperature threshold, the device generates alarm when this temperature is reached.
(from iButton register page.)

ib_sample_rate

how many seconds the temperature samplings are apart from each other during a mission
(from iButton register page.)

seconds

ib_control

Bit 7: Enable Oscillator (EOSC)
Bit 6: Memory Clear Enable (EMCLR)
Bit 4: Enable Mission (EM)
Bit 3: Rollover Enable/Disable (RO)
Bit 2: Temperature Low Alarm Search (TLS)
Bit 1: Temperature High Alarm Search (THS)
Bit 0: Timer Alarm Search (TAS)
(from iButton register page.)

bit flag

ib_rollover

3rd bit of ib_control. Rollover Enable/Disable.
(from iButton register page.)

0,1

ib_mission_start_delay

how many minutes the device waits before starting the logging process
(from iButton register page.)

minutes

ib_status

Status Register.
Bit 7: Temperature Core Busy (TCB)
Bit 6: Memory Cleared (MEMCLR)
Bit 5: Mission in Progress (MIP)
BIT 4: Sample in Progress (SIP)
Bit 2: Temperature Low Flag (TLF)
Bit 1: Temperature High Flag (THF)
Bit 0: Timer Alarm Flag (TAF)
(from iButton register page.)

bit flag

ib_temp

iButton temperature measurement
(from iButton register page.)

ib_mission_start

Time when the mission starts (unix timestamp format).
(from iButton register page.)

ib_mission_samples_counter

how many temperature measurements have taken place during the current mission in progress
(from iButton register page.)

ib_device_samples_counter

how many temperature measurements have taken place since the device was assembled at the factory
(from iButton register page.)

ib_alarm_duration

Alarm duration.
(from Alarm Timestamps page.)

minutes

ib_is_alarm_high

0 : high alarm temperature;
1 : low alarm temperature.
(from Alarm Timestamps page.)

0,1

ib_hist_XXXX

Temperature histogram value.
XXXX is histogram binary address, from 0800 to 087C.
0800 corresponds to -38.5 and lower temperature
0802 corresponds to -38.0 .. -36.5
0804 corresponds to -36.0 .. -34.5
...
087A corresponds to +82.0 .. +83.5
087C corresponds to +84.0 and higher

(from Alarm Timestamps page.)

mileage

Mileage

hdop

HDOP

sat_mode

Sattelite Mode indicator
0 – no fix
1 – Autonomous GNSS Fix
2 – Differential GNSS Fix
3 – Estimated/Dead Reckoning Fix

sat_fix

FS indicator:
0 – invalid
1 – Fix not available
2 – 2D Fix
3 – 3D Fix

is_fixnow

FixNOW indicator:
0 – Continuous mode;
1 – FixNOW mode

is_pedestrian

Pedestrian/Automotive mode indicator:
0 – Automotive;
1 – Pedestrian

ign

Ignition

0,1

fake_ign

“Fake Ignition” flag. If the device detects movement for at least 15 seconds or detects a point farther than MaxGuardDist, it raises this flag. If there is no movement for more than 15 seconds the device clears this flag.

0,1

is_antenna_short_circuit

Antenna short circuit:
0 – antenna OK;
1 – antenna short circuit

0,1

pwr_int

ADC reading for the battery voltage.

log_trigger

Flash write trigger

core_flag

Device status flags and boot up flags (appear only once at device start up).

bit								Meaning
7	6	5	4	3	2	1	0	Meaning
							x	Device reset due to power up occurred.
						x		Device reset due to watchdog reset.
					x			Real Time Clock reset
				x				RAM reset
			x					Flash reset
		x						Firmware update
	x							SD/MMC card present
x								SD/MMC card error

gpo_flag

State of the digital outputs:

bit								Meaning
7	6	5	4	3	2	1	0	Meaning
							x	Ignition
						x		Power supply source; 0 – Internal battery; 1 – External power source
					x			Reserved
				x				Reserved
			x					GPO0 state; 0 – off; 1 – on
		x						GPO0 fault; 0 – no fault; 1 – fault (short circuit)
	x							GPO1 state; 0 – off; 1 – on
x								GPO1 fault; 0 – no fault; 1 – fault (short circuit)

gsm_activity

Current GSM activity:

bit								Meaning
7	6	5	4	3	2	1	0	Meaning
							x	GSM network registration; 0 – not registered; 1 – registered
						x		GPRS attach attempt
					x			Registration within the GPRS network; 0 – not registered; 1 – registered
				x				Call received
			x					Attempt to connect to the ISP using GSM data (CSD)
		x						Attempt to connect to the ISP via GPRS
	x							Attempt to upload a file to the FTP server
x								Attempt to download a file from the FTP server

gsm_resp

Indicates that some of the following messages is received from the GSM:
0 – OK (no error)
1 – ERROR
3 – NO CARRIER
4 – CONNECT
7 – BUSY
8 – NO ANSWER
9 - SHUTDOWN

gsm_cme_err

CME error messages:
1025 - Ok_Info_DataBegin
1028 - Ok_Info_WaitingForData
3074 - Ok_Info_SocketClosed
3077 - Ok_Info_Ppp
3086 - Ok_Info_GprsActivation

driving_reason

bit
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										x	x	x	x	x	x	Driving reason: 0 – Work trip 1 – Private trip
									x							0 – Default driving reason 1- Reason selected by user
								x								N/A
							x									Driving reason info received from DIM-5000
x	x	x	x	x	x	x										N/A

mifare_state

bit
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															x	0 – Card unlog/not logged 1 – Card log to the system
	x	x	x	x	x	x	x	x	x	x	x	x	x	x		N/A
x																0 – MiFare card info never received from DIM-5000 1 – there is MiFare card status message from DIM-5000

mifare_id

MiFare card number

f02_GG_NN

Parameter from configuration frame,
GG - Parameter Group,
NN - Parameter Number

sf02_GG_NN

Status byte for parameters in reply frames.

bit								Value	Meaning
7	6	5	4	3	2	1	0	Value	Meaning
-	0	0	0	0	0	0	0	0	No Error
	0	0	0	0	0	0	1	1	Unsupported parameter group number
	0	0	0	0	0	1	0	2	Unsupported parameter number
	0	0	0	0	0	1	1	3	Value out of range / try to set a read-only parameter
	0	0	0	0	1	0	0	4	Value not set, i.e. the data field value is meaningless
	0	0	0	0	1	0	1	5	Unfinished command is present in the frame
	0	0	0	0	1	1	0	6	An error occurred while writing the settings into the flash (Command reply frame).
	0	0	0	0	1	1	1	7	Command forbidden in *.dcc file or SMS.
	0	0	0	1	0	0	0	8	Device busy (i.e. try to get SD card data start index, while device is reading or writing data).
	0	0	0	1	0	0	1	9	Error accessing a module (i.e. try to get SD card data start index, but there’s no SD card or SD card is damaged)
	0	0	0	1	0	1	0	10	This error is returned by Start Firmware Download command. The device cannot process the command, because another call is being processed at the moment.
	0	0	0	1	0	1	1	11	This error is returned by Start Firmware Download command. The command is sent via SMS, but the sender phone number is not authorized to perform firmware download.
x									This indicates that the last parameter sequence in the frame is unfinished. i.e. the device expected more data, but the frame had ended.

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Junte-se à nossa associação global de especialistas em telemática. Ajude seus clientes a transformar seus negócios com soluções de IoT conectadas e análises profundas.

Solicite o Wialon na sua região

Obtenha uma solução de telemática dos nossos parceiros de confiança para melhorar as operações da sua frota, reduzir custos de manutenção e melhorar a gestão de combustível.

Preencha um formulário de solicitação para começar

PASSO 1

PASSO 2

PASSO 3

Primeiro nome*

Sobrenome*

Empresa*

E-mail*

Telefone

Eu concordo com o processamento de meus dados pessoais
Política de Privacidade

‹ › ×

Produtos

Produtos de nicho para tarefas específicas

DATECS

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Solicite o Wialon na sua região

Preencha um formulário de solicitação para começar