Personal GPS tracker TWIG One | Integrated with Wialon

Features TWIG One:

3G
4G/LTE
Communication vocale

The following data should also be added to TWIG One unit properties section of Wialon GPS tracking software :

Device type:	TWIG One
ID único:	custom

Specify the following parameters in configuration software or configuration TWIG One for use in Wialon Hosting :

Porta do servidor:

22146

15 units of TWIG One device type are connected to Wialon Data Center. This represents 0.07% of all Personal trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
battery	Battery level	%
mode	Mode the instrument is in: norm - normal mode emer - emergency mode test - testing mode.
position_precision	The precision of the position given in the Position field. The range of the field is 0...255 meters. Values more than 254 are always indicated with 255 in the field.	m
pos_src	Source of the position in the message: gps - GPS. Position is acquired from GPS and the timestamp is related to actual acquisition time gpa - position is acquired from GPS, but the timestamp is updated, since no movement is detected with motion sensor after last actual position fix. Note the motion sensor parameters, defining the needed movement. gpb - position is aquired from GPS, but the timestamp is NOT updated, since movement is detected with motion sensor but not calculated by gps. Note the motion sensor parameters defining the needed movement. net - TWIG Point Netloc hybrid location service.
pos_format	Position format in which the position information in the message is given: 1 - WGS-84 2 - WGS-84 with precision.
status_code	Status code: 001: battery low 002: connected to mains 003: disconnected from mains 004: battery too cold 005: battery too hot 006: unknown battery 007: power on 008: power off 009: poor satellite coverage 010: sensor not detected 011: battery temperature out of range 012: charging error 013: accessory battery low 014: wake up for motion sensor 015: wake up for timer 016: man down turned on 017: man down turned off 018: beacon low battery 019: RF tag read. Tag ID also sent 020: DIN0825 start up test OK 021: DIN0825 powering off 022: OSM ACK 023: RfSwitch 024: NFC Tag read. NFC Tag ID also sent 025: Mandown pre-alarm triggered. 026: Docked smart charging station 027: Undocked smart charging station
status_text	Status text: 001: Battery low 002: Mains on / Docked 003: Mains off / Un docked 004: Battery cold 005: Battery warm 006: Unknown battery 007: Power on 008: Power off 009: Poor sat. cov. 010: No sensor 011: Temp. wrong 012: Charging error 013: Low Battery B2 ( number after “B” corresponds to linked RF button number) 014: wake up for motion sensor 015: wake up for timer 016: man down turned on 017: man down turned off 018: beacon low battery 019: RF tag read. Tag ID also sent 020: DIN0825 start up test OK 021: DIN0825 powering off 022: OSM ACK 023: RfSwitch 024: NFC Tag. NFC Tag ID also sent 025: ManDown pre-alarm. ManDown trigger code also sent 026: SDocked (smart charging station ID also sent) 027 SUndocked (smart charging station ID also sent)
msg_num	The message number of the report
emg_text	Predefined text to be sent with the emergency report. 1 = No Movement 2 = Tilt angle 3 = No Movement Tilt angle 4= Freefall 5 = No Movement \| Freefall 6 = Freefall \| Tilt angle 7= No Movement \| Freefall \| Tilt angle 8 = Impact 9 = Impact \| No Movement 10 = Impact \|Tilt angle 11 = Impact \| Tilt angle \| No Movement 12 = Impact \| Freefall 13 = Impact \| Freefall \| No Movement 14 = Impact \| Freefall \| Tilt angle 15 = Impact \| Freefall \| Tilt angle\| No Movement
rcvd_time	Message received time
msg_type	Command name
trigger_type	Trigger type of the condition check process which sent the report.
service_state	Requested Condition Check service state. 0=Deactivated 1=Activated
interval	Query interval of the process which sent the report, in full minutes. If requested deactivation then value is 0
queries missed	Number of queries the user has failed to confirm within the 45-second period.
passcode	Passcode entered into the query by the user.
data	Data from !ASS packet
emg_data_block	The same as 'emg_text'

Parameter name

Description

Units

battery

Battery level

mode

Mode the instrument is in:

norm - normal mode

emer - emergency mode

test - testing mode.

position_precision

The precision of the position given in the Position field.

The range of the field is 0...255 meters. Values more than 254 are always indicated with 255 in the field.

pos_src

Source of the position in the message:

gps - GPS. Position is acquired from GPS and the timestamp is related to actual acquisition time

gpa - position is acquired from GPS, but the timestamp is updated, since no movement is detected with motion sensor after last actual position fix. Note the motion sensor parameters, defining the needed movement.

gpb - position is aquired from GPS, but the timestamp is NOT updated, since movement is detected with motion sensor but not calculated by gps. Note the motion sensor parameters defining the needed movement.

net - TWIG Point Netloc hybrid location service.

pos_format

Position format in which the position information in the message is given:

1 - WGS-84

2 - WGS-84 with precision.

status_code

Status code:

001: battery low

002: connected to mains

003: disconnected from mains

004: battery too cold

005: battery too hot

006: unknown battery

007: power on

008: power off

009: poor satellite coverage

010: sensor not detected

011: battery temperature out of range

012: charging error

013: accessory battery low

014: wake up for motion sensor

015: wake up for timer

016: man down turned on

017: man down turned off

018: beacon low battery

019: RF tag read. Tag ID also sent

020: DIN0825 start up test OK

021: DIN0825 powering off

022: OSM ACK

023: RfSwitch

024: NFC Tag read. NFC Tag ID also sent

025: Mandown pre-alarm triggered.

026: Docked smart charging station

027: Undocked smart charging station

status_text

Status text:

001: Battery low

002: Mains on / Docked

003: Mains off / Un docked

004: Battery cold

005: Battery warm

006: Unknown battery

007: Power on

008: Power off

009: Poor sat. cov.

010: No sensor

011: Temp. wrong

012: Charging error

013: Low Battery B2 ( number after “B” corresponds to linked RF button number)

014: wake up for motion sensor

015: wake up for timer

016: man down turned on

017: man down turned off

018: beacon low battery

019: RF tag read. Tag ID also sent

020: DIN0825 start up test OK

021: DIN0825 powering off

022: OSM ACK

023: RfSwitch

024: NFC Tag. NFC Tag ID also sent

025: ManDown pre-alarm. ManDown trigger code also sent

026: SDocked (smart charging station ID also sent)

027 SUndocked (smart charging station ID also sent)

msg_num

The message number of the report

emg_text

Predefined text to be sent with the emergency report.

1 = No Movement

2 = Tilt angle

3 = No Movement Tilt angle

4= Freefall

5 = No Movement | Freefall

6 = Freefall | Tilt angle

7= No Movement | Freefall | Tilt angle

8 = Impact

9 = Impact | No Movement

10 = Impact |Tilt angle

11 = Impact | Tilt angle | No Movement

12 = Impact | Freefall

13 = Impact | Freefall | No Movement

14 = Impact | Freefall | Tilt angle

15 = Impact | Freefall | Tilt angle| No Movement

rcvd_time

Message received time

msg_type

Command name

trigger_type

Trigger type of the condition check process which sent the report.

service_state

Requested Condition Check service state.

0=Deactivated

1=Activated

interval

Query interval of the process which sent the report, in full minutes. If requested deactivation then value is 0

queries missed

Number of queries the user has failed to confirm within the 45-second period.

passcode

Passcode entered into the query by the user.

data

Data from !ASS packet

emg_data_block

The same as 'emg_text'

Preencha um formulário de solicitação para começar

Produtos

Produtos de nicho para tarefas específicas

TWIG One

More devices from the manufacturer

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Solicite o Wialon na sua região

Preencha um formulário de solicitação para começar