| msg_id |
Message follow-up number (g05) |
|
| msg_ver |
Version of this message, for future use with new message versions |
|
| live_version |
Version of the Live data chapter |
|
| live_ignition |
Ignition state |
|
| live_odometer |
Odometer reading |
m |
| live_fuel_level |
Fuel level percentage in the tank, or battery level percentage for electric vehicles |
% |
| live_speed |
Vehicle speed |
km/h |
| live_board_voltage |
Board (raw) voltage |
V |
| live_key_id |
Driver key / iButton / tachograph driver card ID |
|
| live_input1_state |
Input 1 state, raw voltage |
V |
| live_input2_state |
Input 2 state (boolean) |
|
| live_output1_state |
Output 1 state (boolean) |
|
| live_output2_state |
Output 2 state (boolean) |
|
| live_output3_state |
Output 3 state (boolean) |
|
| live_operating_hours |
Total engine operating hours |
s |
| live_working_operating_hours |
Working (PTO / work-mode) operating hours |
s |
| live_odometer_source |
Source of the odometer value: 0 - UNKNOWN, 1 - CANBUS, 2 - D8, 3 - GNSS |
|
| gnss_version |
Version of the GNSS data chapter |
|
| sat_in_use |
Number of satellites in use |
|
| sat_in_view |
Number of satellites in view |
|
| gps_sat_used |
Number of GPS satellites used |
|
| glonass_sat_used |
Number of GLONASS satellites used |
|
| gnss_cn0_max |
Maximum GNSS C/N0 signal strength, 0-100% |
% |
| has_fix |
Whether the GNSS module has a fix |
|
| gnss_supl_fix |
Whether the position fix was obtained via GNSS SUPL (assisted GNSS) |
|
| gnss_supl_accuracy |
GNSS SUPL position accuracy offset |
m |
| gnss_antenna |
Whether the internal GNSS antenna is used (false means the external antenna is used) |
|
| gnss_status |
GNSS module status |
|
| gnss_fix_age |
Age of the last GNSS fix |
s |
| tacho_version |
Version of the Tacho data chapter |
|
| tacho_driver1_state |
Driver 1 working state (SPN1612), value 7 if ITS is off |
|
| tacho_driver2_state |
Driver 2 working state (SPN1613), value 7 if ITS is off |
|
| tacho_driver1_key |
Driver 1 tachograph card number |
|
| tacho_driver2_key |
Driver 2 tachograph card number |
|
| tacho_driver1_card |
Driver 1 card indicator (SPN1615) |
|
| tacho_driver2_card |
Driver 2 card indicator (SPN1616) |
|
| tacho_driver1_day_start |
Start of day for driver 1 (epoch time) |
|
| tacho_driver2_day_start |
Start of day for driver 2 (epoch time) |
|
| tacho_driver1_night_rest_start |
Start of night rest for driver 1 (epoch time) |
|
| tacho_driver2_night_rest_start |
Start of night rest for driver 2 (epoch time) |
|
| tacho_driver1_driving_budget |
Remaining driving time budget for driver 1 |
min |
| tacho_driver2_driving_budget |
Remaining driving time budget for driver 2 |
min |
| tacho_driver1_work_budget |
Remaining work time budget for driver 1 |
min |
| tacho_driver2_work_budget |
Remaining work time budget for driver 2 |
min |
| tacho_driver1_max_driving_time |
Maximum driving time for driver 1 |
min |
| tacho_driver2_max_driving_time |
Maximum driving time for driver 2 |
min |
| tacho_driver1_max_working_time |
Maximum working time for driver 1 |
min |
| tacho_driver2_max_working_time |
Maximum working time for driver 2 |
min |
| tacho_driver1_rest_before |
Time remaining before required rest start for driver 1 |
min |
| tacho_driver2_rest_before |
Time remaining before required rest start for driver 2 |
min |
| tacho_driver1_min_rest_period |
Minimal rest period for driver 1 |
min |
| tacho_driver2_min_rest_period |
Minimal rest period for driver 2 |
min |
| tacho_driver1_driving_budget_week |
Remaining weekly driving time budget for driver 1 |
min |
| tacho_driver2_driving_budget_week |
Remaining weekly driving time budget for driver 2 |
min |
| tacho_driver1_work_budget_week |
Remaining weekly work time budget for driver 1 |
min |
| tacho_driver2_work_budget_week |
Remaining weekly work time budget for driver 2 |
min |
| tacho_driver1_rest_period_week |
Weekly rest period for driver 1 |
min |
| tacho_driver2_rest_period_week |
Weekly rest period for driver 2 |
min |
| tacho_type |
Tachograph type: 0 = UNKNOWN, 1 = VDO, 2 = SRE |
|
| tacho_time |
Tachograph epoch time |
|
| tacho_drive_recognize |
Drive recognize value, will be 3 if ITS is off |
|
| tacho_overspeed |
Tachograph overspeed indicator, will be 3 if ITS is off |
|
| tacho_vehicle_reg_number |
Vehicle registration number, from tachograph |
|
| tacho_vehicle_reg_codepage |
Vehicle registration number code page |
|
| tacho_vehicle_reg_member_state |
Vehicle registering member state (nation code enum) |
|
| tacho_driver1_card_member_state |
Driver 1 card issuing member state (nation code enum) |
|
| tacho_driver2_card_member_state |
Driver 2 card issuing member state (nation code enum) |
|
| tacho_speed |
Speed reported by the tachograph, will be 255.99 if ITS is off |
km/h |
| tacho_odometer |
Odometer reported by the tachograph |
m |
| tacho_driver1_time_state |
Driver 1 time related state, will be 15 if ITS is off |
|
| tacho_driver2_time_state |
Driver 2 time related state, will be 15 if ITS is off |
|
| tacho_ignition |
Ignition state reported by the tachograph |
|
| tacho_data_change_mask |
Bitmask indicating which tachograph data has changed |
|
| alt_fuel_version |
Version of the Alternative Fuel data chapter |
|
| alt_fuel_propulsion_type |
Propulsion type enum: CONVENTIONAL, HYBRID, ELECTRIC, HYDROGEN, UNDEFINED |
|
| alt_fuel_charging_state |
Charging state enum: NOT_CONNECTED, CONNECTED_NOT_CHARGING, CONNECTED_AND_CHARGING, NOT_IN_USE |
|
| alt_fuel_remaining_charge_time |
Remaining charge time (for electric or plug-in hybrid propulsion) |
s |
| alt_fuel_remaining_range |
Remaining range |
km |
| alt_fuel_current_usage |
Current fuel/energy usage. Depends on vehicle/propulsion type: km/l for conventional, kWh/km for electric, kg/km for CNG and LPG |
|
| alt_fuel_hves_voltage |
High voltage energy storage voltage. Negative when discharging (using), positive when charging |
V |
| alt_fuel_hves_charge_current |
High voltage energy storage charge current |
|
| alt_fuel_hves_discharge_current |
High voltage energy storage discharge current. Negative when discharging (using), positive when charging |
|
| alt_fuel_secondary_fuel_level |
Secondary fuel level: battery voltage or LPG tank level in hybrid solutions, depending on propulsion type |
% |
| dash_version |
Version of the Dashboard data chapter |
|
| dash_rpm |
Engine speed |
rev/min |
| dash_torque |
Torque, percentage of maximum torque |
% |
| dash_accelerator_pedal_pos |
Accelerator pedal position |
% |
| dash_engine_coolant_temp |
Engine coolant temperature |
°C |
| dash_turning_indicator_lights |
Turning indicator lights: 0 = off, 1 = left, 2 = right, 3 = hazard lights |
|
| dash_gear |
Current gear: 255 = reverse, 0 = neutral, other values are the gear number |
|
| dash_fuel_rate |
Fuel consumption rate |
l/h |
| dash_cruise_enabled |
Whether cruise control is enabled |
|
| dash_accelerometer_calibrated |
Whether the accelerometer is fully calibrated towards earth and the front of the vehicle |
|
| dash_accel_x |
Accelerometer X axis acceleration relative to earth and the front of the vehicle |
m/s^2 |
| dash_accel_y |
Accelerometer Y axis acceleration relative to earth and the front of the vehicle |
m/s^2 |
| dash_accel_z |
Accelerometer Z axis acceleration relative to earth and the front of the vehicle |
m/s^2 |
| trip_version |
Version of the Trip data chapter |
|
| trip_id |
Trip ID connecting the start and stop of a trip: first four characters are the last four digits of the IMEI, remaining ten are the local epoch time the trip started/stopped on the device |
|
| trip_config_group_id |
Configuration group ID active during the trip |
|
| trip_config_version |
Configuration group version active during the trip |
|
| trip_driving_time |
Total driving time |
s |
| trip_idle_time |
Total idle time |
s |
| trip_over_speed_time |
Total time spent over the overspeed threshold |
s |
| trip_over_rpm_time |
Total time spent over the RPM threshold |
s |
| trip_over_harsh_accel_time |
Total time spent over the harsh acceleration threshold |
s |
| trip_over_harsh_brake_time |
Total time spent over the harsh brake threshold |
s |
| trip_coasting_time |
Total coasting time |
s |
| trip_coastable_time |
Total coastable time |
s |
| trip_cruise_time |
Total cruise time |
s |
| trip_cruiseable_time |
Total cruiseable time |
s |
| trip_acceleration_time |
Total acceleration time |
s |
| trip_deceleration_time |
Total deceleration time |
s |
| trip_engine_brake_time |
Total engine brake time |
s |
| trip_pto_used_time |
Total PTO used time |
s |
| trip_engine_on_time |
Total engine on time |
s |
| trip_fuel_used |
Total fuel used. Depending on propulsion type can also be MyriaJoule for electric, or KG for CNG and LPG |
L |
| trip_fuel_idle |
Total fuel used while idle. Depending on propulsion type can also be MyriaJoule for electric, or KG for CNG and LPG |
L |
| trip_fuel_used_cruising |
Total fuel used while cruising. Depending on propulsion type can also be MyriaJoule for electric, or KG for CNG and LPG |
L |
| trip_fuel_used_driving |
Total fuel used while driving. Depending on propulsion type can also be MyriaJoule for electric, or KG for CNG and LPG |
L |
| trip_pto_fuel_used |
Fuel used by the PTO. Depending on propulsion type can also be MyriaJoule for electric, or KG for CNG and LPG |
L |
| trip_brakes |
Total number of brake events |
|
| trip_harsh_brakes |
Total number of harsh brake events |
|
| trip_clutch |
Total number of clutch events |
|
| trip_harsh_accelerations |
Total number of harsh acceleration events (not yet implemented on the device) |
|
| trip_stops |
Total number of stops |
|
| trip_overspeed_distance |
Total distance travelled over the overspeed threshold |
m |
| trip_coasting_distance |
Total coasting distance |
m |
| trip_coastable_distance |
Total coastable distance |
m |
| trip_cruise_distance |
Total cruise distance |
m |
| trip_acceleration_distance |
Total acceleration distance |
m |
| trip_deceleration_distance |
Total deceleration distance |
m |
| trip_brake_distance |
Total brake distance |
m |
| trip_engine_brake_distance |
Total engine brake distance |
m |
| trip_propulsion_type |
Propulsion type enum: CONVENTIONAL, HYBRID, ELECTRIC, HYDROGEN, UNDEFINED |
|
| trip_over_idle_threshold_time |
Total time spent over the idle threshold |
s |
| ble_version |
Version of the Bluetooth data chapter |
|
| __id
|
Detected BLE beacon identifier (hex string), where is the Bluetooth protocol ID and its beacon ID
|
|
| __type
|
Type ID of the detected BLE beacon |
|
| __data
|
Raw advertisement data bytes of the detected BLE beacon (hex string) |
|
| __rssi
|
Signal strength of the detected BLE beacon |
dBm |
| __lost_id
|
Identifier (hex string) of a BLE beacon that is no longer detected (lost) |
|
| __lost_rssi
|
Last known signal strength of a lost BLE beacon |
dBm |
| event_version |
Version of the Events data chapter |
|
| event_#_type |
Event type code for reported event #, where # is the event's index in this message |
|
| event_#_link_id |
Link ID for event #: last 4 digits of the IMEI plus epoch time for start/stop events, otherwise '0' * 14, where # is the event's index in this message |
|
| settings_version |
Version of the Settings data chapter |
|
| settings_vin |
Vehicle Identification Number (VIN) configured on the device |
|
| settings_iccid |
SIM card ICCID |
|
| settings_microbooter_version |
Device microbooter firmware version |
|
| settings_booter_version |
Device booter firmware version |
|
| settings_application_version |
Device application firmware version |
|
| settings_qtl_code |
QTL code of the device |
|
| settings_keys_version |
Version of the security keys installed on the device |
|
| settings_temp_version |
Temporary/staged firmware version |
|
| settings_device_serial_number |
Device serial number |
|
| settings_hardware_version |
Device hardware version |
|
| settings_external_5v_enabled |
Whether the external 5V circuit is enabled |
|
| settings_driver_id_enabled |
Whether driver ID functionality is enabled |
|
| settings_driving_style_events_enabled |
Whether driving style events are sent |
|
| settings_input_events_enabled |
Whether IO (input) events are enabled |
|
| settings_tacho_live_enabled |
Whether tachograph live messages are sent |
|
| settings_tacho_download_enabled |
Whether tachograph download is enabled |
|
| settings_output_toggling_enabled |
Whether outputs can be toggled remotely via a command |
|
| settings_pto_enabled |
Whether PTO parameter calculations are enabled |
|
| settings_timed_message_interval_speed_relative_enabled |
Whether timed messages are sent more frequently when speed is low |
|
| settings_high_resolution_recording_enabled |
Whether recording of GNSS data and speed every 5 seconds is enabled |
|
| settings_standby_message_interval |
Time interval messages are sent on while ignition is off |
s |
| settings_time_message_interval |
Time interval messages are sent on while ignition is on |
s |
| settings_driver_id_clear_interval |
Delay after ignition off before the driver gets logged out |
s |
| settings_can_wakeup_enabled |
Whether CAN wakeup is enabled |
|
| settings_minute_rule_enabled |
Whether tachograph minute rule mimicking is enabled |
|
| settings_charging_message_interval |
Interval at which charging status messages are sent while charging |
s |
| settings_can4_purpose |
Purpose configured for CAN4 (off / limp mode / FMS gateway) |
|
| settings_analog_input_function |
Function configured for the analog input (ignition / binary input) |
|
| settings_configuration_group |
Configuration group ID configured on the device |
|
| settings_configuration_group_version |
Configuration group version configured on the device |
|
| settings_emergency_brake_threshold |
Emergency brake detection threshold |
m/s^2 |
| settings_idle_time_delay |
Idle time detection delay |
s |
| settings_harsh_acceleration_threshold |
Harsh acceleration detection threshold |
m/s^2 |
| settings_overspeed_threshold |
Overspeed detection threshold |
km/h |
| settings_high_rpm_threshold |
High RPM detection threshold |
rev/min |
| settings_harsh_brake_threshold |
Harsh brake detection threshold |
m/s^2 |
| settings_high_pedal_threshold |
High accelerator pedal position detection threshold |
% |
| settings_acceleration_threshold |
Acceleration detection threshold |
m/s^2 |
| settings_deceleration_threshold |
Deceleration detection threshold |
m/s^2 |
| settings_longitudinal_movement_threshold |
Longitudinal movement detection threshold |
m/s^2 |
| settings_lateral_movement_threshold |
Lateral movement detection threshold |
m/s^2 |
| settings_coastable_distance_counting_delay |
Coastable distance counting delay |
m |
| settings_cruisable_time_counting_delay |
Cruisable time counting delay |
s |
| settings_over_rpm_time_counting_delay |
Over-RPM time counting delay |
s |
| settings_over_speed_time_counting_delay |
Over-speed time counting delay |
s |
| settings_harsh_brake_detection_speed_threshold |
Minimum speed for harsh brake detection |
km/h |
| settings_stop_speed |
Speed threshold below which the vehicle is considered stopped |
km/h |
| settings_ignition_off_delay |
Delay before ignition off is registered |
s |
| settings_fuel_level_message_delay |
Delay before sending a fuel level message |
s |
| settings_apn |
APN configured on the device |
|
| settings_ep0_time_mask |
Chapter bitmask included in endpoint 0 messages sent on the fixed time interval trigger |
|
| settings_ep0_start_trip_mask |
Chapter bitmask included in endpoint 0 messages sent on the start-of-trip trigger |
|
| settings_ep0_end_trip_mask |
Chapter bitmask included in endpoint 0 messages sent on the end-of-trip trigger |
|
| settings_ep0_charging_mask |
Chapter bitmask included in endpoint 0 messages sent on the charging trigger |
|
| settings_ep0_reserved_mask |
Reserved chapter bitmask for endpoint 0 (currently unused) |
|
| settings_ep0_power_on_reset_mask |
Chapter bitmask included in endpoint 0 messages sent on the power on/reset trigger |
|
| settings_ep0_wakeup_mask |
Chapter bitmask included in endpoint 0 messages sent on the wakeup trigger |
|
| settings_ep0_standby_mask |
Chapter bitmask included in endpoint 0 messages sent on the standby trigger |
|
| settings_ep0_movement_mask |
Chapter bitmask included in endpoint 0 messages sent on the movement detected/stopped trigger |
|
| settings_ep0_low_board_voltage_mask |
Chapter bitmask included in endpoint 0 messages sent on the low board voltage trigger |
|
| settings_ep0_io_change_mask |
Chapter bitmask included in endpoint 0 messages sent on the IO (digital input) change trigger |
|
| settings_ep0_driving_without_login_mask |
Chapter bitmask included in endpoint 0 messages sent on the driving-without-login trigger |
|
| settings_ep0_login_logout_mask |
Chapter bitmask included in endpoint 0 messages sent on the driver login/logout trigger |
|
| settings_ep0_drive_style_mask |
Chapter bitmask included in endpoint 0 messages sent on the driving style event trigger |
|
| settings_ep0_diagnostics_mask |
Chapter bitmask included in endpoint 0 messages sent on the diagnostics trigger |
|
| settings_ep0_tacho_live_mask |
Chapter bitmask included in endpoint 0 messages sent on the tachograph live trigger |
|
| settings_ep0_request_mask |
Chapter bitmask included in endpoint 0 messages sent on explicit request |
|
| settings_ep1_time_mask |
Chapter bitmask included in endpoint 1 messages sent on the fixed time interval trigger |
|
| settings_ep1_start_trip_mask |
Chapter bitmask included in endpoint 1 messages sent on the start-of-trip trigger |
|
| settings_ep1_end_trip_mask |
Chapter bitmask included in endpoint 1 messages sent on the end-of-trip trigger |
|
| settings_ep1_charging_mask |
Chapter bitmask included in endpoint 1 messages sent on the charging trigger |
|
| settings_ep1_reserved_mask |
Reserved chapter bitmask for endpoint 1 (currently unused) |
|
| settings_ep1_power_on_reset_mask |
Chapter bitmask included in endpoint 1 messages sent on the power on/reset trigger |
|
| settings_ep1_wakeup_mask |
Chapter bitmask included in endpoint 1 messages sent on the wakeup trigger |
|
| settings_ep1_standby_mask |
Chapter bitmask included in endpoint 1 messages sent on the standby trigger |
|
| settings_ep1_movement_mask |
Chapter bitmask included in endpoint 1 messages sent on the movement detected trigger |
|
| settings_ep1_low_board_voltage_mask |
Chapter bitmask included in endpoint 1 messages sent on the low board voltage trigger |
|
| settings_ep1_io_change_mask |
Chapter bitmask included in endpoint 1 messages sent on the PZ (input 2) change trigger |
|
| settings_ep1_driving_without_login_mask |
Chapter bitmask included in endpoint 1 messages sent on the driving-without-login trigger |
|
| settings_ep1_login_logout_mask |
Chapter bitmask included in endpoint 1 messages sent on the driver login/logout trigger |
|
| settings_ep1_drive_style_mask |
Chapter bitmask included in endpoint 1 messages sent on the driving style event trigger |
|
| settings_ep1_diagnostics_mask |
Chapter bitmask included in endpoint 1 messages sent on the diagnostics trigger |
|
| settings_ep1_tacho_live_mask |
Chapter bitmask included in endpoint 1 messages sent on the tachograph live trigger |
|
| settings_ep1_request_mask |
Chapter bitmask included in endpoint 1 messages sent on explicit request |
|
| settings_ep2_time_mask |
Chapter bitmask included in endpoint 2 messages sent on the fixed time interval trigger |
|
| settings_ep2_start_trip_mask |
Chapter bitmask included in endpoint 2 messages sent on the start-of-trip trigger |
|
| settings_ep2_end_trip_mask |
Chapter bitmask included in endpoint 2 messages sent on the end-of-trip trigger |
|
| settings_ep2_charging_mask |
Chapter bitmask included in endpoint 2 messages sent on the charging trigger |
|
| settings_ep2_reserved_mask |
Reserved chapter bitmask for endpoint 2 (currently unused) |
|
| settings_ep2_power_on_reset_mask |
Chapter bitmask included in endpoint 2 messages sent on the power on/reset trigger |
|
| settings_ep2_wakeup_mask |
Chapter bitmask included in endpoint 2 messages sent on the wakeup trigger |
|
| settings_ep2_standby_mask |
Chapter bitmask included in endpoint 2 messages sent on the standby trigger |
|
| settings_ep2_movement_mask |
Chapter bitmask included in endpoint 2 messages sent on the movement detected trigger |
|
| settings_ep2_low_board_voltage_mask |
Chapter bitmask included in endpoint 2 messages sent on the low board voltage trigger |
|
| settings_ep2_io_change_mask |
Chapter bitmask included in endpoint 2 messages sent on the PZ (input 2) change trigger |
|
| settings_ep2_driving_without_login_mask |
Chapter bitmask included in endpoint 2 messages sent on the driving-without-login trigger |
|
| settings_ep2_login_logout_mask |
Chapter bitmask included in endpoint 2 messages sent on the driver login/logout trigger |
|
| settings_ep2_drive_style_mask |
Chapter bitmask included in endpoint 2 messages sent on the driving style event trigger |
|
| settings_ep2_diagnostics_mask |
Chapter bitmask included in endpoint 2 messages sent on the diagnostics trigger |
|
| settings_ep2_tacho_live_mask |
Chapter bitmask included in endpoint 2 messages sent on the tachograph live trigger |
|
| settings_ep2_request_mask |
Chapter bitmask included in endpoint 2 messages sent on explicit request |
|
| diag_version |
Version of the Diagnostics data chapter |
|
| diag_num_can_ids |
Number of CAN identifiers reported in this section |
|
| diag_can_id_# |
CAN identifier being monitored, where # is its index in the reported list |
|
| diag_modem_connection_status |
Current modem connection status |
|
| diag_modem_connection_mode |
Current modem connection mode/technology |
|
| diag_modem_rssi |
Current modem signal strength (RSSI) |
|
| diag_modem_snr |
Current modem signal-to-noise ratio (SNR) |
|
| diag_modem_plmn |
Current modem PLMN (mobile network) code |
|
| diag_modem_signal_strength |
Current modem mobile network signal strength |
|
| diag_num_logs |
Number of modem connection log entries reported |
|
| diag_log_#_reason |
Reason for the modem connection log entry, where # is its index in the reported list |
|
| diag_log_#_time |
Time (epoch) of the modem connection log entry, where # is its index in the reported list |
|
| diag_log_#_connection_status |
Connected/disconnected status for the modem connection log entry, where # is its index in the reported list |
|
| diag_log_#_connection_mode |
Connection technology for the modem connection log entry: NO_SERVICE/GSM/CAT_M1/NB_IOT, where # is its index in the reported list |
|
| diag_log_#_rssi |
Signal strength (RSSI) for the modem connection log entry, where # is its index in the reported list |
|
| diag_log_#_snr |
Signal-to-noise ratio (SNR) for the modem connection log entry, where # is its index in the reported list |
|
| diag_log_#_plmn |
PLMN (mobile network) code for the modem connection log entry, where # is its index in the reported list |
|
| endpoint_version |
Version of the Endpoint Data chapter |
|
| endpoint_0_url |
Configured URL for endpoint 0 |
|
| endpoint_0_url_path |
Configured URL path for endpoint 0 |
|
| endpoint_0_protocol |
Internet protocol used for endpoint 0: 1 = http, 2 = https, 3 = tcp |
|
| endpoint_1_url |
Configured URL for endpoint 1 |
|
| endpoint_1_url_path |
Configured URL path for endpoint 1 |
|
| endpoint_1_protocol |
Internet protocol used for endpoint 1: 1 = http, 2 = https, 3 = tcp |
|
| endpoint_2_url |
Configured URL for endpoint 2 |
|
| endpoint_2_url_path |
Configured URL path for endpoint 2 |
|
| endpoint_2_protocol |
Internet protocol used for endpoint 2: 1 = http, 2 = https, 3 = tcp |
|
| endpoint_authserver_url |
Configured authentication server URL |
|
| endpoint_authserver_url_path |
Configured authentication server URL path |
|
| endpoint_authserver_protocol |
Internet protocol used for the authentication server: 1 = http, 2 = https, 3 = tcp |
|
| high_res_version |
Version of the High resolution record data chapter |
|
| high_res_num_records |
Number of high resolution data records included in this section |
|
| high_res_fix |
Whether the high resolution record has a GNSS fix |
|
| high_res_odometer |
Odometer value for the high resolution record (present since chapter version 2) |
m |
