dev_type |
Queclink device type
*HEX mode only
|
|
proto_ver |
Queclink protocol version
*HEX mode only
|
|
fw_ver |
Firmware version
*HEX mode only
|
|
battery |
Internal battery level, 0-100% |
% |
pwr_ext |
External power source voltage |
V |
adc_mode |
Analog Input Mode |
|
adc1 |
Analog Input 1 voltage |
V |
din_status |
Digital Input Status Bitmask Ignition Detection: 0x01 Digital Input 1: 0x02 Digital Input 2: 0x04 Digital Input 3: 0x08
|
|
dout_status |
Digital Output Status Bitmask Digital Output 1: 0x01 Digital Output 2: 0x02 Digital Output 3: 0x04
|
|
motion_status |
Current motion state of the device. 17 (0x11) Ignition Off Rest: Vehicle is ignition off and motionless. 18 (0x12) Ignition Off Motion: Vehicle moving while ignition is off (towing event). 33 (0x21) Ignition On Rest: Vehicle is ignition on and motionless. 34 (0x22) Ignition On Motion: Vehicle is ignition on and moving. 65 (0x41) Sensor Rest: Vehicle is motionless (no ignition signal). 66 (0x42) Sensor Motion: Vehicle is moving (no ignition signal). 22 (0x16) Tow: Vehicle was towed after ignition off. 26 (0x1A) Fake Tow: Vehicle may have been towed after ignition off.
|
|
phone_number |
Phone number associated with the device's SIM card. |
|
ign_dur |
Ignition duration in seconds, reported with ignition-off events. |
s |
can_group_id |
Identifier for the CAN bus data group being transmitted. |
|
can_alarm_mask_1 |
First bitmask for CAN bus alarms. |
|
can_alarm_mask_2 |
Second bitmask for CAN bus alarms. |
|
can_alarm_mask_3 |
Third bitmask for CAN bus alarms. |
|
ibutton |
The unique identifier of the connected iButton or 1-Wire device. |
|
ibutton_auth |
Authentication status of the iButton. 0 - Not Authorized, 1 - Authorized. |
|
geo_id |
ID of the Geo-Fence that triggered the event. |
|
ges_enabled |
Parking-Fence enable status. 0 - Disabled, 1 - Enabled. |
|
ges_mode |
Parking-Fence mode. 0 - Triggered by ignition off, 1 - Triggered by command. |
|
ges_radius |
Radius of the Parking-Fence in meters. |
m |
ges_dt |
Time duration in seconds before a Parking-Fence alarm is triggered. |
s |
jamming_cw |
Continuous wave (cellular) jamming detection status. 0 - No jamming, 1 - Jamming detected. |
|
jamming_gps |
GPS signal jamming detection status. 0 - No jamming, 1 - Jamming detected. |
|
upc_cmd_id |
User Private Command ID. Identifier for a user-defined command. |
|
upc_result |
Result code of the User Private Command execution. |
|
url |
A URL, often for location sharing or other web features. |
|
onewire[i]_id |
Identifier of the i-th connected 1-Wire peripheral. |
|
onewire[i]_type |
Type of the i-th connected 1-Wire peripheral (e.g., temperature sensor). |
|
onewire[i]_data |
Data read from the i-th connected 1-Wire peripheral. |
|
fuel_sensor[i]_type |
Type of the i-th connected fuel sensor. |
|
fuel_sensor[i]_id |
Identifier of the i-th connected fuel sensor. |
|
fuel_sensor[i]_percent |
Fuel level percentage from the i-th sensor. |
% |
fuel_sensor[i]_volume |
Fuel volume from the i-th sensor in Liters. |
L |
pwr_int |
Internal battery voltage. |
V |
upd_code |
Code indicating the status of a firmware or configuration update. |
|
upd_retry |
Number of retry attempts for an update process. |
|
idle_dt |
Duration of the vehicle's idle state in seconds. |
s |
gps_signal_status |
Indicates the status and quality of the GPS signal reception. |
|
wave1_out_id |
Identifier for the WAVE1 output. |
|
wave1_out_active |
Activation status of the WAVE1 output. 0 - Inactive, 1 - Active. |
|
temp_alarm_id |
Identifier of the temperature alarm that was triggered. |
|
temp_status |
Status of the temperature sensor. 0 - Normal, 1 - Alarm. |
|
temp_device_id |
Identifier of the temperature sensing device (e.g., 1-Wire sensor ID). |
|
temp_device_data |
Temperature data read from the device in degrees Celsius. |
°C |
roaming_state |
Roaming status of the cellular connection. 0 - Home network, 1 - Roaming. |
|
fuel_input_id |
Identifier of the analog input used for fuel level sensing. |
|
fuel_level_last |
The previously recorded fuel level value. |
|
fuel_level_current |
The currently recorded fuel level value. |
|
mup_event |
Indicates a motion under power-off event. |
|
phl_mask |
Pre-defined harsh driving behavior level mask. |
|
fuel_sensor_type |
Type of the connected fuel sensor. |
|
fuel_hw_fault_code |
Hardware fault code related to the fuel sensor. |
|
ufs_code |
User file system code, related to file operations on the device. |
|
file_name |
Name of a file, typically related to updates, logs, or photos. |
|
cfu_code |
Configuration update result code. |
|
mcc |
Mobile Country Code of the current cellular network. |
|
mnc |
Mobile Network Code of the current cellular network. |
|
lac |
Location Area Code of the current cellular network. |
|
cell_id |
Cell ID of the currently connected cellular tower. |
|
curr_mileage |
Current Trip Mileage in meters
*HEX mode only
|
m |
total_mileage |
Total Mileage in meters
*HEX mode only
|
m |
curr_hourmetercount |
Current Trip Hour Meter Count in seconds (accumulative ignition time)
*HEX mode only
|
s |
total_hourmetercount |
Total Hour Meter Count in seconds (accumulative ignition time)
*HEX mode only
|
s |
fri_discard_no_fix |
Flag indicating if FRI (Fixed Report Interval) reports should be discarded without a GPS fix. 0 - Send anyway, 1 - Discard. |
|
resp_report_mask |
A bitmask to configure which fields are included in +RESP messages. |
|
ign_dt |
Report interval in seconds when ignition is on. |
s |
igf_dt |
Report interval in seconds when ignition is off. |
s |
bat_status |
Status of the internal battery. 0: Normal, 1: Charging, 2: Charge Complete, 3: Low Battery. |
|
iccid |
The ICCID (Integrated Circuit Card Identifier) of the SIM card. |
|
csq_ber |
CSQ Bit Error Rate, a value from 0-7 or 99 if unknown. |
|
daylight_saving |
Daylight Saving Time offset in hours. |
h |
time_zone |
Time zone offset from UTC in minutes. |
min |
sens_proto_ver |
Protocol version of a connected sensor. |
|
sens_sw_ver |
Software version of a connected sensor. |
|
sens_hw_ver |
Hardware version of a connected sensor. |
|
can100_sw_ver |
Software version of the CAN100 module. |
|
can100_serial |
Serial number of the CAN100 module. |
|
adcf |
Fuel level in percent, derived from an analog input. |
% |
gps_acc |
GNSS Accuracy. A value indicating GNSS fix status and HDOP. 0 means the current GNSS fix failed. A non-zero value (1-50) means the fix is successful and represents the HDOP value. |
|
buffer |
Indicates if the message was buffered or live. 0: Live message (e.g., +RESP header). 1: Buffered message (e.g., +BUFF header).
|
|
msg_type_name |
The message type name of the report (e.g., GTFRI, GTRTL). |
|
ign |
Ignition status. 0: Ignition off. 1: Ignition on.
|
|
report_type |
The meaning of Report Type varies by message type. - +RESP:GTFRI: 0-Normal, 1-Corner, 2-Freq Change, 4-Mileage.
- +RESP:GTSPD: 0-Outside range, 1-Inside range.
- +RESP:GTHBM: 0-Harsh Braking, 1-Harsh Accel, 2-Harsh Cornering.
- +RESP:GTGES: 0-Fence inactive, 1-Fence active.
- +RESP:GTTMP: 0-Outside temp range, 1-Inside temp range.
- (See protocol documentation for a full list).
|
|
inputs |
Status of the digital inputs as a bitmask. |
|
outputs |
Status of the digital outputs as a bitmask. |
|
report_id |
The meaning of Report ID varies by message type. - GTDIS/GTSOS: ID of the triggering digital input.
- GTHBM: Speed level of the harsh behavior (1-Low, 2-Medium, 3-High).
- GTGES: ID of the triggered Geo-Fence.
- GTTMP: ID of the temperature alarm.
- (See protocol documentation for a full list).
|
|
report |
Indicates the protocol format of the report. +RESP, +BUFF: ASCII format. +RSP, +BSP, etc.: HEX format.
|
|
mileage |
The current total mileage in meters. |
m |
backup_battery |
The current charge level of the backup battery. |
% |
device_status |
A composite status field. It may include motion status, input/output states, and peripheral states in a single hexadecimal value. |
|