Queclink GV310LAU

Queclink GV310LAU
Forum de discussion

Nombre des unités

788
En ligne
1358
Nombre total
Caractéristiques Queclink GV310LAU:
  • 2G
  • 4G/LTE
  • Boîte à mémoire

Afin d'identifier le boîtier Queclink GV310LAU les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Queclink GV310LAU
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GV310LAU pour les utiliser dans Wialon Hosting :

Port du serveur: 22396

1358 unités Queclink GV310LAU connectées au le centre de données Wialon — Ça fait 0.06% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
dev_type

Queclink device type
*HEX mode only

proto_ver

Queclink protocol version
*HEX mode only

fw_ver

Firmware version
*HEX mode only

battery

Battery level, 0-100

pwr_ext

External power source voltage

adc_mode

Analog Input Mode

adc1

Analog Input 1 voltage

din_status

Digital Input Mode
Ignition Detection 0x01
Digital Input1 0x02
Digital Input2 0x04
Digital Input3 0x08

dout_status

Digital Output Mode
Digital Output1 0x01
Digital Output2 0x02
Digital Output3 0x04

motion_status
phone_number
ign_dur
can_group_id
can_alarm_mask_1
can_alarm_mask_2
can_alarm_mask_3
ibutton
ibutton_auth
geo_id
ges_enabled
ges_mode
ges_radius
ges_dt
jamming_cw
jamming_gps
upc_cmd_id
upc_result
url
onewire[i]_id
onewire[i]_type
onewire[i]_data
fuel_sensor[i]_type
fuel_sensor[i]_id
fuel_sensor[i]_percent
fuel_sensor[i]_volume
pwr_int
upd_code
upd_retry
idle_dt
gps_signal_status
wave1_out_id
wave1_out_active
temp_alarm_id
temp_status
temp_device_id
temp_device_data
roaming_state
fuel_input_id
fuel_level_last
fuel_level_current
mup_event
phl_mask
fuel_sensor_type
fuel_hw_fault_code
ufs_code
file_name
cfu_code
mcc
mnc
lac
cell_id
curr_mileage

Current Trip Mileage
*HEX mode only

total_mileage

Total Mileage
*HEX mode only

curr_hourmetercount

Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only

total_hourmetercount

Total Hour Meter Count (accumulative ignition time)
*HEX mode only

fri_discard_no_fix
resp_report_mask
ign_dt
igf_dt
bat_status
iccid
csq_ber

CSQ BER,0-7/99

daylight_saving
time_zone
sens_proto_ver
sens_sw_ver
sens_hw_ver
can100_sw_ver
can100_serial
adcf fuel level in percent
gps_acc

GNSS Accuracy

A numeral to indicate the GNSS fix status and HDOP of the GNSS position. 0 means the current GNSS fix fails and the last known GNSS position is used. A non-zero value (1 - 50) means the current GNSS fix is successful and represents the HDOP of the current GNSS position.

buffer

Parameter that shows if the message was buffered (sent with +BUFF: header) or live (sent with +RESP: header)

  • buffer = 0 - RESP:
  • buffer = 1 - BUFF:

msg_type_name

Message type name of the report


ign

Ignition status

  • ign = 0, ignition off
  • ign = 1, ignition on

report_type

Report type has different meanings in different messages as follows:

  • +RESP:GTDIS
    • 0: The current logic status of the input port is “Disable status”.
    • 1: The current logic status of the input is “Enable status”.
  • +RESP:GTIOB
    • 0: The current logic status of the bound IO does not meet the alarm condition.
    • 1: The current logic status of the bound IO meets the alarm condition.
  • +RESP:GTSPD
    • 0: Outside of the predefined speed range.
    • 1: Inside of the predefined speed range In the protocol watchdog reboot message
  • +RESP:GTDOG
    • 1: Reboot message for time based working mode
    • 2: Reboot message for ignition on working mode
    • 3: Reboot message for input triggered reboot
    • 4: Reboot message for GSM watchdog reboot
    • 5: Reboot message for GPRS watchdog reboot
    • 6: Reboot message for send failure watchdog
  • +RESP:GTIGL
    • 0: The engine is ignition on.
    • 1: The engine is ignition off.
  • +RESP:GTHBM
    • 0: Harsh braking behavior
    • 1: Harsh acceleration behavior
    • 2: Harsh cornering behavior
    • 3: Harsh braking and cornering behavior
    • 4: Harsh acceleration and cornering behavior
    • 5: Unknown harsh driving behavior For other messages, it will always be 0.
  • +RESP:GTFRI
    • 0: Normal fixed report.
    • 1: Corner report which indicates that the device just turns around a corner.
    • 2: Change of FRI report frequency which indicates that the device enters into Geo-Fence status or roaming status.
    • 3: Corner report when FRI report frequency changes.
    • 4: Mileage report when fixed report is mode 5.
    • 5: Reserved.
    • 6: Mileage report when fixed report is mode 5 and FFC works.
  • +RESP:GTAIS | +RESP GTEPS
    • 0: Outside the predefined range
    • 1: Inside the predefined range
  • +RESP:GTGES
    • 0 indicates “Current Parking-Fence is inactive”
    • 1 indicates “Current Parking-Fence is active”.
  • +RESP:GTTMP
    • 0 means “Outside the predefined temperature range”
    • 1 means “Inside the predefined temperature range”.
  • +RESP:GTUDT A numeral to indicate the type of the report.
    • 0: Timer event triggered.
    • 1: GEO-Fence event triggered.
    • 2: PEO-Fence event triggered.

inputs

Digital inputs

outputs

Digital outputs

report_id

Report ID has different meanings in different messages as follows

  • The ID of digital input port which triggers the report message +RESP:GTDIS and+RESP:GTSOS. The range is 1 – 3 and 9 – C.
  • The ID of the bound IO which triggers the report message +RESP:GTIOB. The range is 0 – 3.
  • The ID of the digital input port which triggers the reboot message +RESP:GTDOG. The valid value is 1 or 2.
  • The speed level at which the harsh behavior is detected in the message +RESP:GTHBM.
    • “3” indicates high speed
    • “2” indicates medium speed
    • “1” indicates low speed.
    • If mode 2 is chosen, the value will always be 0 which indicates unknown speed.
  • The value of ign_mode which indicates the trigger source of the message +RESP:GTVGL. The value range is 0 – 4|7.
  • The type of speed alarm which triggers the report message +RESP:GTSPD. The range is 0 – 0xF.
  • +RESP:GTFRI
    • 1: Fixed time report.
    • 2: Fixed distance report.
    • 3: Fixed mileage report.
    • 4: Fixed time and mileage report.
    • 5: Fixed time or mileage report.
  • +RESP:GTEPS | +RESP:GTAIS
    • The ID of the analog input port which triggers the report message +RESP:GTEPS. The value is 0. The ID of the analog input port which triggers the report message +RESP:GTAIS. The range is 1-2 or 5.
  • +RESP:GTGES
    • The ID of Geo-Fence in HEX format. The range is 0 to 13.
  • +RESP:GTTMP
    • The ID of the temperature alarm. The range is 0-3
  • +RESP:GTUDT
    • GEO-Fence / PEO-Fence event triggered report ID.
  • For other messages, it will always be 0 if parameter exists



report

Shows the header and protocol format

  • +RESP, +BUFF - ASCII Hormat
  • +RSP,+BSP,+EVT,+BVT,+INF,+BNF - Hex format

mileage

The current total mileage

backup_battery

The current volume of backup battery

%
device_status

The status of the device. From left to right, the first two characters indicate EIO100 input status, the second two characters indicate EIO100 output status, the third two characters indicate the current motion status of the device, the fourth two characters indicate the status of input ports, and the last two characters indicate the status of output ports.

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom et nom *
Entreprise*
Email*
Téléphone