Queclink GL521MG

Queclink GL521MG
Forum de discussion

Nombre des unités

31
En ligne
348
Nombre total
Caractéristiques Queclink GL521MG:
  • 4G/LTE
  • Boîte à mémoire
  • BLE enabled
Compatible avec Wialon:
  • Gestion à distance via GPRS
  • LBS
  • Communication via TCP
  • Communication via UDP

Afin d'identifier le boîtier Queclink GL521MG les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Queclink GL521MG
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GL521MG pour les utiliser dans Wialon Hosting :

Port du serveur: 22290

348 unités Queclink GL521MG connectées au le centre de données Wialon — Ça fait 0.19% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
temp_int

The real time temperature value of the terminal. It must be noted that the
temperature
function must be enabled in the in the AT+GTTEM command, otherwise this field is empty

rx_level

The network signal strength level. The range is 0-31, and 99 is for unknown signal strength

avl_driver

The id number of the driver represented in decimal format

active_mode

Current mode of the device.
0: Power saving mode (PSM)
1: Continuous mode

battery

Current volume of the battery

%
cell_id

Cell ID (CID) is a generally unique number used to identify each base transceiver station (BTS) or sector of a BTS within a LAC if not within a GSM network

gps_acc

A numeral to indicate the GPS fix status and HDOP of the GPS position.

0 - GPS fix fails and the last known GPS position is used

1-50 - GPS fix is successful and represents the HDOP of the current GPS position

lac

Each location area has an assigned unique identifier, made up of numbers, called a "location area code" (LAC). The LAC is broadcast by each base station at regular intervals. Within a location area, each base station is assigned a distinct "cell identifier" (CI) number

mcc

Mobile country code. It is 3-digit in length and ranges from 000–999.

mnc

Mobile network code. It is 3-digit in length and ranges from 000–999.

movement_status

The movement status of the device. It must be noted that the sensor
function must, otherwise this field is empty.

0: Stillness
1: Motion

msg_type_name

The message ID of HEX format report

proto_ver

The protocol version that the terminal conforms to.

rep_type
GTGEO GTNMR GTDOG GTDIS GTAIS
0: Exit the correspondig Geo-fence 0: The state of the device changed from motion to rest 0: Reboot periodically according to the Interval and Time Settings 0: The current logical state of the input port is disabled state. 0: Outside of the predefined range
1: Enter the corresponding Geo-fence 1: The state of the device changed from rest to motion 1: The current logical state of the input is enabled state 1: Inside of the predefined range
report_type

The message type of ASCII format report

rx_ber

The network quality of the signal. The range is 0-7, and 99 is for unknown signal quality

evt_state1 | evt_state2
GTBPL GTTEM GTLSA GTLTA
evt_state1 evt_state2 evt_state1 evt_state2 evt_state1 evt_state2 evt_state1 evt_state2
0 0 The temperature alarm state: 0 The light sensor alarm state 0 The light sensor tamper state 0
1 - The current temp is lower that the low temp threshold specified by Min. Temperature. 0: Normal state 0: Normal State
2 -The current temperature is higher than the high temperature threshold specified by Max.Temp 1: Above threshold alarm state 1: Tamper alarm state
3: The current temperature is within the temperature threshold range. 2: Below threshold alarm state
4: The current temp is outside the temperature threshold range
rep_id

The type of the messages GTGEO, GTDOG and GTNMR.
For other reports, it is 0.

For GTGEO
0: Exit the corresponding Geo-fence

1: Enter the corresponding Geo-fence

For GTNMR
0: The sta
te of the device changed from motion to rest
1: The state of the device changed from rest to motion

For GTDOG
0:
Reboot periodically according to settings

For GTGEO
0:
The current logical state of the input port is disabled state
1:
The current logical state of the input is enabled state

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom et nom *
Entreprise*
Email*
Téléphone