Queclink GL530MG

Queclink GL530MG
Forum de discussion

Nombre des unités

0
En ligne
13
Nombre total
Caractéristiques Queclink GL530MG:
  • 4G/LTE
  • Boîte à mémoire
  • Installation magnétique

Afin d'identifier le boîtier Queclink GL530MG les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Queclink GL530MG
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GL530MG pour les utiliser dans Wialon Hosting :

Port du serveur: 22415

13 unités Queclink GL530MG connectées au le centre de données Wialon — Ça fait 0.01% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
report_id

Report ID

(not set)
report_type

Report Type

(not set)
mcc

Mobile country code

(not set)
mnc

Mobile network code

(not set)
lac

Location area code in hex format

(not set)
cell_id

Cell ID in hex format

(not set)
csq_rssi

The signal strength level

(not set)
csq_ber

The quality of the signal

(not set)
battery

Current volume of the battery in percentage

%
pwr_int

Battery voltage

V
mode_selection

Current mode of the device.

0: Power saving mode (PSM)

1: Continuous mode

(not set)
movement_status

The movement status of the device

0: rest

1: Motion

(not set)
temp_int

The real time temperature value of the device

°C
phone_number

The phone number which initiates this report

(not set)
iccid

The ICCID of the installed SIM card

(not set)
total_pac

The total number of messages.

(not set)
curr_pac

The sequence number of the current message

(not set)
config

The current configurations of the device

(not set)
time_zone

Time zone

(not set)
daylight_saving

Daylight Saving

(not set)
apn

APN

(not set)
apn_username

APN User Name

(not set)
apn_password

APN Password

(not set)
backup_apn

Backup APN

(not set)
backup_apn_username

Backup APN User Name

(not set)
backup_apn_password

Backup APN Password

(not set)
ip_address

IP Address

(not set)
main_dns

Main DNS

(not set)
backup_dns

Backup DNS

(not set)
network_type

Network Type

(not set)
sv_id_[i]

The satellite ID

(not set)
sv_power_[i]

Satellite power

(not set)
ati_mask

ATI Mask

(not set)
soft_ver

The firmware version of the device

(not set)
mcu_soft_ver

The MCU firmware version of the device

(not set)
modem_soft_ver

The Modem software version of the device

(not set)
hard_ver

The hardware version of the device

(not set)
modem_hard_ver

The Modem hardware version of the device

(not set)
sensor_id

It indicates the type of the sensor currently used by the device

(not set)
power_on_type

A numeral to indicate how the device is activated.

  1. Movement detected by the device
  2. Specified time reached
  3. Light sensor alarm event
  4. Manual power on with the key button for the first time
  5. RTO command or watchdog reboot
  6. Abnormal power on
  7. RTC error
  8. FOTA process
  9. Temperature sensor alarm event
  10. Reset PIN

(not set)
event_state_1

The temperature alarm state

  1. The current temperature is lower than the low temperature threshold specified by Min. Temperature.
  2. The current temperature is higher than the high temperature threshold specified by Max. Temperature .
  3. The current temperature is within the temperature threshold range.
  4. The current temperature is outside the temperature threshold range.

(not set)
event_state_2 Event state 2 (not set)
light_level

The level of light intensity detected by the device

(not set)
fix_type

A string which indicates the type of GNSS fix this cell information is for.

"FRI": This cell information is for FRI request.

"RTL": This cell information is for RTL request.

"GIR": This cell information is for GIR request

(not set)
mcc[i]

MCC of the neighbor cell i

(not set)
mnc[i]

MNC of the neighbor cell i

(not set)
lac[i]

LAC of the neighbor cell i

(not set)
cell_id[i]

Cell ID of the neighbor cell i

(not set)
rx_level[i]

The signal strength of the neighbor cell i

0: -110 dBm

1 to 62: -109 to -48 dBm

63: -47 dBm

(not set)
command_id

The command ID in the update configuration file.

(not set)
result

A numeral to indicate whether the configuration is updated successfully.

  • 100: The update command is starting.
  • 101: The update command is confirmed by the device.
  • 102: The update command is refused by the device.
  • 103: The update process is refused because the battery is low.
  • 200: The device starts to download the package.
  • 201: The device finishes downloading the package successfully.
  • 202: The device fails to download the package.
  • 300: The device starts to update the device configuration.
  • 301: The device finishes updating the device configuration successfully.
  • 302: The device fails to update the device configuration.
  • 305: The update process is interrupted by reboot.
  • 306: The update process is interrupted by MD5 verification error.

(not set)
url

The complete URL to download the configuration. It includes the file name.

(not set)
id_number

Identifier Number

(not set)

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom*
Nom*
Entreprise*
Email*
Téléphone