Asset GPS tracker Queclink GL530MG | Integrated with Wialon

Features Queclink GL530MG:

4G/LTE
Caixa preta
Montagem magnética

The following data should also be added to Queclink GL530MG unit properties section of Wialon GPS tracking software :

Device type:	Queclink GL530MG
ID único:	imei

Specify the following parameters in configuration software or configuration Queclink GL530MG for use in Wialon Hosting :

Porta do servidor:

22415

101 units of Queclink GL530MG device type are connected to Wialon Data Center. This represents 0.07% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
report_id	Report ID	(not set)
report_type	Report Type	(not set)
mcc	Mobile country code	(not set)
mnc	Mobile network code	(not set)
lac	Location area code in hex format	(not set)
cell_id	Cell ID in hex format	(not set)
csq_rssi	The signal strength level	(not set)
csq_ber	The quality of the signal	(not set)
battery	Current volume of the battery in percentage	%
pwr_int	Battery voltage	V
mode_selection	Current mode of the device. 0: Power saving mode (PSM) 1: Continuous mode	(not set)
movement_status	The movement status of the device 0: rest 1: Motion	(not set)
temp_int	The real time temperature value of the device	°C
phone_number	The phone number which initiates this report	(not set)
iccid	The ICCID of the installed SIM card	(not set)
total_pac	The total number of messages.	(not set)
curr_pac	The sequence number of the current message	(not set)
config	The current configurations of the device	(not set)
time_zone	Time zone	(not set)
daylight_saving	Daylight Saving	(not set)
apn	APN	(not set)
apn_username	APN User Name	(not set)
apn_password	APN Password	(not set)
backup_apn	Backup APN	(not set)
backup_apn_username	Backup APN User Name	(not set)
backup_apn_password	Backup APN Password	(not set)
ip_address	IP Address	(not set)
main_dns	Main DNS	(not set)
backup_dns	Backup DNS	(not set)
network_type	Network Type	(not set)
sv_id_[i]	The satellite ID	(not set)
sv_power_[i]	Satellite power	(not set)
ati_mask	ATI Mask	(not set)
soft_ver	The firmware version of the device	(not set)
mcu_soft_ver	The MCU firmware version of the device	(not set)
modem_soft_ver	The Modem software version of the device	(not set)
hard_ver	The hardware version of the device	(not set)
modem_hard_ver	The Modem hardware version of the device	(not set)
sensor_id	It indicates the type of the sensor currently used by the device	(not set)
power_on_type	A numeral to indicate how the device is activated. Movement detected by the device Specified time reached Light sensor alarm event Manual power on with the key button for the first time RTO command or watchdog reboot Abnormal power on RTC error FOTA process Temperature sensor alarm event Reset PIN	(not set)
event_state_1	The temperature alarm state The current temperature is lower than the low temperature threshold specified by Min. Temperature. The current temperature is higher than the high temperature threshold specified by Max. Temperature . The current temperature is within the temperature threshold range. The current temperature is outside the temperature threshold range.	(not set)
event_state_2	Event state 2	(not set)
light_level	The level of light intensity detected by the device	(not set)
fix_type	A string which indicates the type of GNSS fix this cell information is for. "FRI": This cell information is for FRI request. "RTL": This cell information is for RTL request. "GIR": This cell information is for GIR request	(not set)
mcc[i]	MCC of the neighbor cell i	(not set)
mnc[i]	MNC of the neighbor cell i	(not set)
lac[i]	LAC of the neighbor cell i	(not set)
cell_id[i]	Cell ID of the neighbor cell i	(not set)
rx_level[i]	The signal strength of the neighbor cell i 0: -110 dBm 1 to 62: -109 to -48 dBm 63: -47 dBm	(not set)
command_id	The command ID in the update configuration file.	(not set)
result	A numeral to indicate whether the configuration is updated successfully. 100: The update command is starting. 101: The update command is confirmed by the device. 102: The update command is refused by the device. 103: The update process is refused because the battery is low. 200: The device starts to download the package. 201: The device finishes downloading the package successfully. 202: The device fails to download the package. 300: The device starts to update the device configuration. 301: The device finishes updating the device configuration successfully. 302: The device fails to update the device configuration. 305: The update process is interrupted by reboot. 306: The update process is interrupted by MD5 verification error.	(not set)
url	The complete URL to download the configuration. It includes the file name.	(not set)
id_number	Identifier Number	(not set)

Parameter name

Description

Units

report_id

Report ID

(not set)

report_type

Report Type

(not set)

mcc

Mobile country code

(not set)

mnc

Mobile network code

(not set)

lac

Location area code in hex format

(not set)

cell_id

Cell ID in hex format

(not set)

csq_rssi

The signal strength level

(not set)

csq_ber

The quality of the signal

(not set)

battery

Current volume of the battery in percentage

pwr_int

Battery voltage

mode_selection

Current mode of the device.

0: Power saving mode (PSM)

1: Continuous mode

(not set)

movement_status

The movement status of the device

0: rest

1: Motion

(not set)

temp_int

The real time temperature value of the device

°C

phone_number

The phone number which initiates this report

(not set)

iccid

The ICCID of the installed SIM card

(not set)

total_pac

The total number of messages.

(not set)

curr_pac

The sequence number of the current message

(not set)

config

The current configurations of the device

(not set)

time_zone

Time zone

(not set)

daylight_saving

Daylight Saving

(not set)

apn

APN

(not set)

apn_username

APN User Name

(not set)

apn_password

APN Password

(not set)

backup_apn

Backup APN

(not set)

backup_apn_username

Backup APN User Name

(not set)

backup_apn_password

Backup APN Password

(not set)

ip_address

IP Address

(not set)

main_dns

Main DNS

(not set)

backup_dns

Backup DNS

(not set)

network_type

Network Type

(not set)

sv_id_[i]

The satellite ID

(not set)

sv_power_[i]

Satellite power

(not set)

ati_mask

ATI Mask

(not set)

soft_ver

The firmware version of the device

(not set)

mcu_soft_ver

The MCU firmware version of the device

(not set)

modem_soft_ver

The Modem software version of the device

(not set)

hard_ver

The hardware version of the device

(not set)

modem_hard_ver

The Modem hardware version of the device

(not set)

sensor_id

It indicates the type of the sensor currently used by the device

(not set)

power_on_type

A numeral to indicate how the device is activated.

Movement detected by the device
Specified time reached
Light sensor alarm event
Manual power on with the key button for the first time
RTO command or watchdog reboot
Abnormal power on
RTC error
FOTA process
Temperature sensor alarm event
Reset PIN

(not set)

event_state_1

The temperature alarm state

The current temperature is lower than the low temperature threshold specified by Min. Temperature.
The current temperature is higher than the high temperature threshold specified by Max. Temperature .
The current temperature is within the temperature threshold range.
The current temperature is outside the temperature threshold range.

(not set)

event_state_2

Event state 2

(not set)

light_level

The level of light intensity detected by the device

(not set)

fix_type

A string which indicates the type of GNSS fix this cell information is for.

"FRI": This cell information is for FRI request.

"RTL": This cell information is for RTL request.

"GIR": This cell information is for GIR request