GPS tracker Queclink GL300VC | Integrated with Wialon

Features Queclink GL300VC:

Caixa preta

Supported in Wialon:

Gerenciamento remoto via GPRS
LBS
Gerenciamento remoto via SMS
Comunicação via TCP
Comunicação via UDP

The following data should also be added to Queclink GL300VC unit properties section of Wialon GPS tracking software :

Device type:	Queclink GL300VC
ID único:	imei

Specify the following parameters in configuration software or configuration Queclink GL300VC for use in Wialon Hosting :

Porta do servidor:

21054

1497 units of Queclink GL300VC device type are connected to Wialon Data Center. This represents 0.06% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
battery	Battery level	%
charging	Whether the battery is charging when the external power supply is connected: 0: Not charging 1: Charging
external_pwr	External power supply: 0: Not connected 1: Connected
gps_antenna_type	A numeric to indicate which GPS antenna is working now 0: inside GPS antenna
gps_on_need	Whether to close GPS chip after retrieving GPS position information: 0: Never close GPS chip 1: Close GPS chip after retrieving GPS information every time 2: Never close GPS chip only in ignition on state or movement state 3: Never open GPS chip
gsm_level	The GSM signal strength level
gsm_quality	The quality of GSM signal
hdop	Horizontal Dilution of Precision
ign	Ignition state: 0: off, 1: on
ign_off_duration	Duration since last time the ignition is off	s
ign_on_duration	Duration since last time the ignition is on	s
led_on	The working mode of LEDs
mileage	The total mileage	km
movement_cause	The enter movement cause defines the factor who triggers the message: 0: Triggered by motion sensor detection. It is defaulted 1: Triggered by RTO sub command RTL 2: Triggered by the command GTLSW from EBK
movement_state	0: The state of the device changed from motion to rest 1: The state of the device changed from rest to motion
odo_mileage	The total mileage in the position	km
pwr_int	Battery voltage	V
report_type	Message type
state	The current motion state of the device: 21: The device attached vehicle is ignition on and motionless 22: The device attached vehicle is ignition on and moving 41: The device is motionless without ignition on 42: The device is moving without ignition on
temp_int	The temperature of the device	°C
geo_active	Indicate active or deactive Geo-Fence: 0 - Deactivate Geo-Fence 1 - Activate Geo-Fence
geo_mode	The new mode of Geo-Fence
geo_radius	The radius of Geo-Fence	m
geo_ch_int	The check interval of Geo-Fence	sec
upd_code	Confirmation/downloading/updating information from firmware updating: 100/110: the update command is confirmed by the device. 101/111: the update command is refused by the device. 102/112: the update process is canceled by the backend server. 103/113: the update process is refused because the battery is low. 200/210: the device starts to download the package. 201/211: the device finishes downloading the package successfully. 202/212: the device fails to download the package. 300/310: the device starts to update the firmware. 301/311: the device finishes updating the firmware successfully. 302/312: the device fails to update the firmware. 303/313: the update process does not start because the battery is low.
dw_times	The count number of the package downloading.

Parameter name

Description

Units

battery

Battery level

charging

Whether the battery is charging when the external power supply is connected:
0: Not charging
1: Charging

external_pwr

External power supply:
0: Not connected
1: Connected

gps_antenna_type

A numeric to indicate which GPS antenna is working now
0: inside GPS antenna

gps_on_need

Whether to close GPS chip after retrieving GPS position information:
0: Never close GPS chip
1: Close GPS chip after retrieving GPS information every time
2: Never close GPS chip only in ignition on state or movement state
3: Never open GPS chip

gsm_level

The GSM signal strength level

gsm_quality

The quality of GSM signal

hdop

Horizontal Dilution of Precision

ign

Ignition state: 0: off, 1: on

ign_off_duration

Duration since last time the ignition is off

ign_on_duration

Duration since last time the ignition is on

led_on

The working mode of LEDs

mileage

The total mileage

movement_cause

The enter movement cause defines the factor who triggers the message:
0: Triggered by motion sensor detection. It is defaulted
1: Triggered by RTO sub command RTL
2: Triggered by the command GTLSW from EBK

movement_state

0: The state of the device changed from motion to rest
1: The state of the device changed from rest to motion

odo_mileage

The total mileage in the position

pwr_int

Battery voltage

report_type

Message type

state

The current motion state of the device:
21: The device attached vehicle is ignition on and motionless
22: The device attached vehicle is ignition on and moving
41: The device is motionless without ignition on
42: The device is moving without ignition on

temp_int

The temperature of the device

°C

geo_active

Indicate active or deactive Geo-Fence:
0 - Deactivate Geo-Fence
1 - Activate Geo-Fence

geo_mode

The new mode of Geo-Fence

geo_radius

The radius of Geo-Fence

geo_ch_int

The check interval of Geo-Fence

sec

upd_code

Confirmation/downloading/updating information from firmware updating:
100/110: the update command is confirmed by the device.
101/111: the update command is refused by the device.
102/112: the update process is canceled by the backend server.
103/113: the update process is refused because the battery is low.
200/210: the device starts to download the package.
201/211: the device finishes downloading the package successfully.
202/212: the device fails to download the package.
300/310: the device starts to update the firmware.
301/311: the device finishes updating the firmware successfully.
302/312: the device fails to update the firmware.
303/313: the update process does not start because the battery is low.

dw_times

The count number of the package downloading.