The following data should also be added to Queclink GL521MG unit properties section of Wialon GPS tracking software :
Device type:
Queclink GL521MG
ID único:
imei
Specify the following parameters in configuration software or configuration Queclink GL521MG for use in Wialon Hosting :
Porta do servidor:
22290
2601 units of Queclink GL521MG device type are connected to Wialon Data Center. This represents 1.95% of all Asset trackers connected.
Below chart represents the dynamic of connections in the last 30 days:
Parameter name
Description
Units
temp_int
The real time temperature value of the terminal. It must be noted that the temperature function must be enabled in the in the AT+GTTEM command, otherwise this field is empty
rx_level
The network signal strength level. The range is 0-31, and 99 is for unknown signal strength
avl_driver
The id number of the driver represented in decimal format
active_mode
Current mode of the device. 0: Power saving mode (PSM) 1: Continuous mode
battery
Current volume of the battery
%
cell_id
Cell ID (CID) is a generally unique number used to identify each base transceiver station (BTS) or sector of a BTS within a LAC if not within a GSM network
gps_acc
A numeral to indicate the GPS fix status and HDOP of the GPS position.
0 - GPS fix fails and the last known GPS position is used
1-50 - GPS fix is successful and represents the HDOP of the current GPS position
lac
Each location area has an assigned unique identifier, made up of
numbers, called a "location area code" (LAC). The LAC is broadcast by
each base station at regular intervals. Within a location area, each
base station is assigned a distinct "cell identifier" (CI) number
mcc
Mobile country code. It is 3-digit in length and ranges from 000–999.
mnc
Mobile network code. It is 3-digit in length and ranges from 000–999.
movement_status
The movement status of the device. It must be noted that the sensor function must, otherwise this field is empty. 0: Stillness 1: Motion
msg_type_name
The message ID of HEX format report
proto_ver
The protocol version that the terminal conforms to.
rep_type
GTGEO
GTNMR
GTDOG
GTDIS
GTAIS
0: Exit the correspondig Geo-fence
0: The state of the device changed from motion to rest
0: Reboot periodically according to the Interval and Time Settings
0: The current logical state of the input port is disabled state.
0: Outside of the predefined range
1: Enter the corresponding Geo-fence
1: The state of the device changed from rest to motion
1: The current logical state of the input is enabled state
1: Inside of the predefined range
report_type
The message type of ASCII format report
rx_ber
The network quality of the signal. The range is 0-7, and 99 is for unknown signal quality
evt_state1 | evt_state2
GTBPL
GTTEM
GTLSA
GTLTA
evt_state1
evt_state2
evt_state1
evt_state2
evt_state1
evt_state2
evt_state1
evt_state2
0
0
The temperature alarm state:
0
The light sensor alarm state
0
The light sensor tamper state
0
1 - The current temp is lower that the low temp threshold specified by Min. Temperature.
0: Normal state
0: Normal State
2 -The current temperature is higher than the high temperature threshold specified by Max.Temp
1: Above threshold alarm state
1: Tamper alarm state
3: The current temperature is within the temperature threshold range.
2: Below threshold alarm state
4: The current temp is outside the temperature threshold range
rep_id
The type of the messages GTGEO, GTDOG and GTNMR. For other reports, it is 0.
For GTGEO 0: Exit the corresponding Geo-fence 1: Enter the corresponding Geo-fence
For GTNMR 0: The state of the device changed from motion to rest 1: The state of the device changed from rest to motion
For GTDOG 0: Reboot periodically according to settings
For GTGEO 0: The current logical state of the input port is disabled state 1: The current logical state of the input is enabled state
bt_index_N
The index of Bluetooth accessory defined in AT+GTBAS which triggers the +RESP:GTBAA message.
0xFF for WKF300 N - number of the accessory in a queue.
bt_type_N
The type of the Bluetooth accessory which is defined in bt_index_N. The following are supported now:
0: No Bluetooth accessory.
1: Reserved.
2: Beacon temperature sensor.
3: Bluetooth Beacon ID accessory (WKF300).
5: Reserved.
6: Beacon Temperature & humidity sensor.
7: Reserved.
8: External Input/output Bluetooth accessory.
N - number of the accessory in a queue.
bt_model_N
The model of the Bluetooth accessory defined in bt_type_N The following is supported now:
The model for bt_type_N is 6 (Beacon temperature/humidity sensor):
0: WTH300.
The external input/output Bluetooth accessory (bt_type_N is 8):
0: WBC300.
The model for bt_type_N is 10 (Physical Web Beacon):
0: WID300
N - number of the accessory in a queue.
bt_raw_data_N
The data is read from the Bluetooth accessory. N - number of the accessory in a queue.
bt_name_N
The name of the Bluetooth accessory. N - number of the accessory in a queue.
bt_mac_N
The MAC of the Bluetooth accessory. N - number of the accessory in a queue.
bt_status_N
Indicates the connection status of Bluetooth accessory.
0: Disconnected.
1: Connected.
bt_battery_lvl_N
The voltage of the Bluetooth accessory. N - number of the accessory in a queue.
V
bt_temp_N
Temperature data of Bluetooth accessory. N - number of the accessory in a queue.
°C
bt_hum_N
Humidity data of the Bluetooth accessory. N - number of the accessory in a queue.
Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática
Seja um parceiro
Junte-se à nossa associação global de especialistas em telemática. Ajude seus clientes a transformar seus negócios com soluções de IoT conectadas e análises profundas.
Solicite o Wialon na sua região
Obtenha uma solução de telemática dos nossos parceiros de confiança para melhorar as operações da sua frota, reduzir custos de manutenção e melhorar a gestão de combustível.
Preencha um formulário de solicitação para começar
