GPS tracker Queclink GV53MG | Integrated with Wialon

Features Queclink GV53MG:

2G
4G/LTE
Caixa preta

The following data should also be added to Queclink GV53MG unit properties section of Wialon GPS tracking software :

Device type:	Queclink GV53MG
ID único:	imei

Specify the following parameters in configuration software or configuration Queclink GV53MG for use in Wialon Hosting :

Porta do servidor:

22185

2148 units of Queclink GV53MG device type are connected to Wialon Data Center. This represents 0.09% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
device_type	Queclink device type *HEX mode only
protocol_ver	Queclink protocol version *HEX mode only
firmware_ver	Firmware version *HEX mode only
pwr_ext	External power source voltage
adc1	Analog Input 1 voltage
din_status	Digital Input (bit mask)
motion_status
ibutton
ges_enabled	Current Parking-Fence is active or inactive. 0 Current Parking -Fence is inactive. 1 Current Parking -Fence is active.
ges_mode
geo_area_type	0 - Polygon GEO 1 - Circle GEO
x_forward
y_forward
z_forward
x_side
y_side
z_side
x_vert
y_vert
z_vert
pwr_int	Internal power source
roaming_state
iccid
daylight_saving
time_zone
mnc[i]	Mobile network code. It is 3 digits in length and ranges from 000–999.
lac[i]	Location area code in hex format.
cell_id[i]	Cell ID in hex format.
gps_level
sat_[sv_id]
ledon	1 - Cell LED anf GNSS LED turn on as configured 2 - Both LEDs work 10 minutes after tge device is powered on and then will be off.
charging	Wheter the backup battery is charging when the main power supply is connected
is_pwr_ext	whether the external power supply is connected.
id	The ID which is currently read
id_reptype	The ID is unauthorized or the ID authorization (IDA) function is disabled; The ID is authorized
rep_id	Report ID has different meanings in different messages as listed below. Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL) The ID of digital input port which triggers the message +RESP:GTSOS. The range is 1 – 2. The ID of the bound IO which triggers the message +RESP:GTIOB. The value is 0. The ID of the digital input port which triggers the reboot message +RESP:GTDOG. The valid value is 1. The speed level at which the harsh behavior is detected in the message +RESP:GTHBM. 3 indicates high speed, 2 indicates medium speed and 1 indicates low speed. The value of <Virtual Ignition Mode> which indicates the trigger source of the message +RESP:GTVGL. 2: External power voltage mode (virtual ignition detection) 3: Reserved 4: Accelerometer mode (virtual ignition detection) 7: Combined detection mode (virtual ignition detection) The ID of Digital Input status which triggers the report message +RESP:GTDIS. The rangeis 1 or 2. For other messages, it will always be 0. GTFRI: 1: Fixed time report. 2: Fixed distance report. 3: Fixed mileage report. 4: Fixed time and mileage report. 5: Fixed time or mileage report. GTEPS\GTAIS: The ID of the analog input port which triggers the report message +RESP:GTEPS. The value is 0 The ID of the analog input port which triggers the report message +RESP:GTAIS. The value is or 5.
rep_type	Report Type has different meanings in different messages: Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL) GTFRI\GTERI: 5: Reserved. 6: Mileage report when fixed report is in mode 5 and AT+GTFFC works GTEPS\GTAIS: 0: Outside the predefined range. 1: Inside the predefined range.
mileage	The current total mileage.
ign	Ignition state 0 - OFF 1 - ON

Parameter name

Description

Units

device_type

Queclink device type
*HEX mode only

protocol_ver

Queclink protocol version

*HEX mode only

firmware_ver

Firmware version
*HEX mode only

pwr_ext

External power source voltage

adc1

Analog Input 1 voltage

din_status

Digital Input (bit mask)

motion_status

ibutton

ges_enabled

Current Parking-Fence is active or inactive.

0 Current Parking -Fence is inactive.

1 Current Parking -Fence is active.

ges_mode

geo_area_type

0 - Polygon GEO
1 - Circle GEO

x_forward

y_forward

z_forward

x_side

y_side

z_side

x_vert

y_vert

z_vert

pwr_int

Internal power source

roaming_state

iccid

daylight_saving

time_zone

mnc[i]

Mobile network code. It is 3 digits in length and ranges from 000–999.

lac[i]

Location area code in hex format.

cell_id[i]

Cell ID in hex format.

gps_level

sat_[sv_id]

ledon

1 - Cell LED anf GNSS LED turn on as configured
2 - Both LEDs work 10 minutes after tge device is powered on and then will be off.

charging

Wheter the backup battery is charging when the main power supply is connected

is_pwr_ext

whether the external power supply is connected.

The ID which is currently read

id_reptype

The ID is unauthorized or the ID authorization (IDA) function is disabled;
The ID is authorized

rep_id

Report ID has different meanings in different messages as listed below.

Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL)
- The ID of digital input port which triggers the message +RESP:GTSOS. The range is 1 – 2.
- The ID of the bound IO which triggers the message +RESP:GTIOB. The value is 0.
- The ID of the digital input port which triggers the reboot message +RESP:GTDOG. The valid value is 1.
- The speed level at which the harsh behavior is detected in the message +RESP:GTHBM. 3 indicates high speed, 2 indicates medium speed and 1 indicates low speed.
- The value of <Virtual Ignition Mode> which indicates the trigger source of the message +RESP:GTVGL.
  2: External power voltage mode (virtual ignition detection)
  3: Reserved
  4: Accelerometer mode (virtual ignition detection)
  7: Combined detection mode (virtual ignition detection)
- The ID of Digital Input status which triggers the report message +RESP:GTDIS. The rangeis 1 or 2.
- For other messages, it will always be 0.
GTFRI:
- 1: Fixed time report.
- 2: Fixed distance report.
- 3: Fixed mileage report.
- 4: Fixed time and mileage report.
- 5: Fixed time or mileage report.
GTEPS\GTAIS:
- The ID of the analog input port which triggers the report message +RESP:GTEPS. The value is 0
- The ID of the analog input port which triggers the report message +RESP:GTAIS. The value is or 5.

rep_type

Report Type has different meanings in different messages:

Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL)
GTFRI\GTERI:
- 5: Reserved.
- 6: Mileage report when fixed report is in mode 5 and AT+GTFFC works
GTEPS\GTAIS:
- 0: Outside the predefined range.
- 1: Inside the predefined range.

mileage

The current total mileage.

ign

Ignition state
0 - OFF
1 - ON