Traceur GPS Queclink GV56 | Intégré à Wialon

Caractéristiques Queclink GV56:

Boîte à mémoire

Compatible avec Wialon:

Capteurs analogiques (ADC)
Capteurs numériques
LBS
Communication via TCP
Communication via UDP

Afin d'identifier le boîtier Queclink GV56 les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS:	Queclink GV56
ID unique:	imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GV56 pour les utiliser dans Wialon Hosting :

Port du serveur:

21707

3197 unités Queclink GV56 connectées au le centre de données Wialon — Ça fait 0.13% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre

Description

Unités

dev_type

Queclink device type
*HEX mode only

proto_ver

Queclink protocol version
*HEX mode only

fw_ver

Firmware version
*HEX mode only

battery

Battery level, 0-100

pwr_ext

External power source voltage

adc_mode

Analog Input Mode

adc1

Analog Input 1 voltage

din_status

Digital Input (bit mask)

dout_status

Digital Output (bit mask)

motion_status

phone_number

ign_dur

ibutton

ibutton_auth

geo_id

ges_enabled

ges_mode

ges_radius

ges_dt

geo_area_type

geo_mask_group

geo_area_mask_group_1

geo_area_mask_group_2

jamming_cw

jamming_gps

upc_cmd_id

upc_result

url

x_forward

y_forward

z_forward

x_side

y_side

z_side

x_vert

y_vert

z_vert

onewire[i]_id

onewire[i]_type

onewire[i]_data

fuel_sensor[i]_type

fuel_sensor[i]_id

fuel_sensor[i]_percent

fuel_sensor[i]_volume

pwr_int

jamming_status

crash_counter

upd_code

upd_retry

idle_dt

gps_signal_status

wave1_out_id

wave1_out_active

temp_alarm_id

temp_status

temp_device_id

temp_device_data

roaming_state

curr_mileage

Current Trip Mileage
*HEX mode only

total_mileage

Total Mileage
*HEX mode only

curr_hourmetercount

Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only

total_hourmetercount

Total Hour Meter Count (accumulative ignition time)
*HEX mode only

hw_ver

mcu_ver

fri_discard_no_fix

resp_report_mask

ign_dt

igf_dt

bat_status

iccid

csq_ber

CSQ BER,0-7/99

daylight_saving

time_zone

tcp_cmd_count

udp_cmd_count

sms_cmd_count_white

sms_cmd_count

tcp_msg_count

udp_msg_count

sms_msg_count_white

sms_msg_count

gir_trigger

mnc[i]

lac[i]

cell_id[i]

ta[i]

rx_level[i]

gps_level

jamming_indicator

sat_[sv_id]

local_ip

ledon

1 - Cell LED anf GNSS LED turn on as configured
2 - Both LEDs work 10 minutes after tge device is powered on and then will be off.

charging

Wheter the backup battery is charging when the main power supply is connected

pwr_s

whether the external power supply is connected.

csq_rssi

the level of signal strength

The ID which is currently read

id_reptype

The ID is unauthorized or the ID authorization (IDA) function is disabled;
The ID is authorized

indx

The index of Bluetooth accessory defined in AT+GTBAS which triggers the +RESP:GTBAA message
0xFF for WKF300

acces_type

0 - No bluetooth accessory
1 - Reserved
2 - Beacon temperature sensor
3 - BLE beacon ID device

acbe_model

The model of the bluetooth accessory

alarm_type

0 - the voltage of the Bluetooth accessory is low
1 - the temperature alarm: current temperature value is below
2 - the temperature alarm: current temperature value is upper
3 - the temperature alarm: current temperature value is within the range defined by <low temperature> and <high temperature>
4 - Push button event on WKF300 is detected

bt_name

Bluetooth accessory name

bt_mac

Bluetooth accessory mac

bt_status