Queclink GV56

Queclink GV56
Discusión en el foro

Cantidad de unidades

1880
En línea
3278
Total
Características Queclink GV56:
  • Caja negra
Soportado en Wialon:
  • Sensores ADC
  • Sensores Digitales
  • LBS
  • Comunicación vía TCP
  • Comunicación por UDP

Para que el sistema de rastreo Wialon identifique los datos de Queclink GV56 en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo: Queclink GV56
ID único: imei

Indique los siguientes parámetros en el programa de configuración o en la configuración Queclink GV56 para utilizarlos en Wialon Hosting :

Puerto del servidor: 21707

En el centro de servicio Wialon se utilizan 3278 unidades Queclink GV56 — es 0.14% de la cantidad total de dispositivos Automóvil conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro Descripción Unidades de medida
dev_type

Queclink device type
*HEX mode only

proto_ver

Queclink protocol version
*HEX mode only

fw_ver

Firmware version
*HEX mode only

battery

Battery level, 0-100

pwr_ext

External power source voltage

adc_mode

Analog Input Mode

adc1

Analog Input 1 voltage

din_status

Digital Input (bit mask)

dout_status

Digital Output (bit mask)

motion_status
phone_number
ign_dur
ibutton
ibutton_auth
geo_id
ges_enabled
ges_mode
ges_radius
ges_dt
geo_area_type
geo_mask_group
geo_area_mask_group_1
geo_area_mask_group_2
jamming_cw
jamming_gps
upc_cmd_id
upc_result
url
x_forward
y_forward
z_forward
x_side
y_side
z_side
x_vert
y_vert
z_vert
onewire[i]_id
onewire[i]_type
onewire[i]_data
fuel_sensor[i]_type
fuel_sensor[i]_id
fuel_sensor[i]_percent
fuel_sensor[i]_volume
pwr_int
jamming_status
crash_counter
upd_code
upd_retry
idle_dt
gps_signal_status
wave1_out_id
wave1_out_active
temp_alarm_id
temp_status
temp_device_id
temp_device_data
roaming_state
curr_mileage

Current Trip Mileage
*HEX mode only

total_mileage

Total Mileage
*HEX mode only

curr_hourmetercount

Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only

total_hourmetercount

Total Hour Meter Count (accumulative ignition time)
*HEX mode only

hw_ver
mcu_ver
fri_discard_no_fix
resp_report_mask
ign_dt
igf_dt
bat_status
iccid
csq_ber

CSQ BER,0-7/99

daylight_saving
time_zone
tcp_cmd_count
udp_cmd_count
sms_cmd_count_white
sms_cmd_count
tcp_msg_count
udp_msg_count
sms_msg_count_white
sms_msg_count
gir_trigger
mnc[i]
lac[i]
cell_id[i]
ta[i]
rx_level[i]
gps_level
jamming_indicator
sat_[sv_id]
local_ip
ledon
  • 1 - Cell LED anf GNSS LED turn on as configured
  • 2 - Both LEDs work 10 minutes after tge device is powered on and then will be off.
charging Wheter the backup battery is charging when the main power supply is connected
pwr_s whether the external power supply is connected.
csq_rssi the level of signal strength
id The ID which is currently read
id_reptype
  • The ID is unauthorized or the ID authorization (IDA) function is disabled;
  • The ID is authorized
indx
  • The index of Bluetooth accessory defined in AT+GTBAS which triggers the +RESP:GTBAA message
  • 0xFF for WKF300
acces_type
  • 0 - No bluetooth accessory
  • 1 - Reserved
  • 2 - Beacon temperature sensor
  • 3 - BLE beacon ID device
acbe_model

The model of the bluetooth accessory

alarm_type
  • 0 - the voltage of the Bluetooth accessory is low
  • 1 - the temperature alarm: current temperature value is below
  • 2 - the temperature alarm: current temperature value is upper
  • 3 - the temperature alarm: current temperature value is within the range defined by <low temperature> and <high temperature>
  • 4 - Push button event on WKF300 is detected
bt_name Bluetooth accessory name
bt_mac Bluetooth accessory mac
bt_status
  • 0 - the accessory is not available
  • 1 - the accessory is available
bt_bat_level The voltage of Bluetooth accessory
bt_temp Temperature data fo Bluetooth accessory
can_eng_torgue Engine Torgue
bt_flvl#

Fuel level from the Bluetooth data

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Paso 1
Paso 2
Paso 3
Nombre de pila*
Apellido*
Compañía*
Email*
Teléfono