Queclink GV305CEU

Queclink GV305CEU
Forum de discussion

Nombre des unités

0
En ligne
6
Nombre total
Caractéristiques Queclink GV305CEU:
  • 4G/LTE
  • BLE enabled
  • Compatibilité avec GLONASS
Compatible avec Wialon:
  • Accéléromètre
  • Capteurs analogiques (ADC)
  • Identification du conducteur
  • Capteurs numériques
  • Gestion à distance via SMS
  • Communication via TCP
  • Communication via UDP

Afin d'identifier le boîtier Queclink GV305CEU les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Queclink GV305CEU
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GV305CEU pour les utiliser dans Wialon Hosting :

Port du serveur: 22495

6 unités Queclink GV305CEU connectées au le centre de données Wialon — Ça fait 0% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
dev_type

Queclink device type
*HEX mode only

proto_ver

Queclink protocol version
*HEX mode only

fw_ver

Firmware version
*HEX mode only

battery

Battery level, 0-100

pwr_ext

External power source voltage

adc_mode

Analog Input Mode

adc1

Analog Input 1 voltage

din_status

Digital Input Mode
Ignition Detection 0x01
Digital Input1 0x02
Digital Input2 0x04
Digital Input3 0x08

dout_status

Digital Output Mode
Digital Output1 0x01
Digital Output2 0x02
Digital Output3 0x04

motion_status
curr_mileage

Current Trip Mileage
*HEX mode only

total_mileage

Total Mileage
*HEX mode only

curr_hourmetercount

Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only

total_hourmetercount

Total Hour Meter Count (accumulative ignition time)
*HEX mode only

csq_ber

CSQ BER,0-7/99

adcf fuel level in percent
lat_#
onewire#_temp

1-Wire temperature #, where # - number

can_total_brakes The total number of braking processes initiated by brake pedal
ign_off_duration Duration since last time the ignition is off
adc# Sensor Type
can_total_effective_eng_speed_time

Total time when the vehicle engine speed is effective

geo_area_mask_group_1

The bitwise mask for trigger condition composition of the corresponding GEO ID. Each bit, from bit 0 to bit 19, represents the logical state of the corresponding GEO ID to trigger the entering or exiting event. 1 means “The event of the GEO ID set is triggered”, and 0 means “The event of the GEO ID set is not triggered”.

bt#_index Index of the Bluetooth device
can_total_dist_imp

Vehicle total distance measured in Impulses (if distance from dashboard is not available)

I
head Report head
can_rapid_brakings Number of total rapid brakings since installation
ext_gps_ant External gps antena
bt#_type

<Accessory Type>: The type of the Bluetooth accessory which is defined in the <Index>. The following is supported now:

  • 0: No Bluetooth accessory.
  • 1: Escort Bluetooth Accessory.
  • 2: Beacon temperature sensor
  • 6: Beacon Multi-Functional Sensor.
  • 7: Technoton accessory

adc3 Analog input 3
can_fuel_consumpt Fuel consumption
can_ign_key Ignition key, 0-no, 1-yes
can_total_accel_kickdown_time Total time when accelerator pedal is pressed over 90%
eio100_inputs The status of EIO100 inputs. For each bit, 0 means “Disable status”, and 1 means “Enable status”.
can_fuel_level_p The level of fuel in vehicle tank
onewire#_id 1-Wire ID #, where # - number
bt#_output
can_tacho_drv2_name The name of driver 2 from the tachograph
digit_fuel_sensor_data

<Digital Fuel Sensor Data>: The raw data read from the digital fuel sensor. If Bit 0 of <ERI Mask> in AT+GTFRI is enabled, this field will be displayed; otherwise, this field will not be displayed.

can_tacho_motion_sign The vehicle motion signal in the tachograph. 0: Motion is not detected 1: Motion is detected.
can_speed CAN speed value
onewire#_data 1-Wire data #, where # - number
onewire#_type 1-Wire type #, where # - number
pwr_int Internal Battery voltage
can_tacho_ovspd

Vehicle overspeed signal from the tachograph.

0: Overspeed is not detected.

1: Overspeed is detected.

can_all_starts

Total number of engine starts

can_fuel_level_l The level of fuel in vehicle tank
can_fuel_consumpt_unit Indicates the unit. The unit L/100km is represented as FE, and the unit L/H is represented as FF
can_eng_cool_temp Engine coolant temperature
mnc Mobile network code
serial_num Tracker serial number
can_range The number of kilometers to drive on remaining fuel
fuel_sensor#_type

The sensor type for the currently set table.

0: EPSILON ES2 or ES4
1: LLS 20160
2: DUT-E
3: QFS100
4: UFSxxx
5: Reserved
6: DUT-E SUM
20: ADC1
21: Reserved

rf#_type
ign_dur

Duration of Ignition

Duration of ignition ON (Report GTIGF)

Duration of ignition OFF (Report GTIGN)

can_handbrake_applies

Count events when handbrake is pulled-up while driving (speed is greater than 5 km/h)

can_ad_blue_lvl The level of Ad-Blue
can_tacho_drv2_card_number The card number of driver 2 from the tachograph
mcc Mobile Country Code
can_total_cruise_cntrl_time Weight of vehicle’s second axle
can_axle_weight_2 Weight of vehicle’s second axle
adc2 ADC2 input current value
can_ain1 The value of analog input
bt#_mask

If the device is connected with the Bluetooth accessory, and the

Bit 8 (for <Bluetooth Accessory Data>) of <ERI Mask> is set to 1, the device will report

+RESP:GTERI instead of +RESP:GTFRI. This mask is used to configure the accessory data fields to be reported in the +RESP:GTERI and +RESP:GTBAR messages.

  • Bit 0: <Accessory Name>
  • Bit 1: <Accessory MAC>
  • Bit 2: <Accessory Status>
  • Bit 3: <Accessory Battery Level>
  • Bit 4: <Accessory Temperature>
  • Bit 5: <Accessory Humidity>
Note

: When <Accessory Type> is set to 7, Bit 3-5 will be blocked. And when <Accessory Type> is set to 1 or 2, Bit 5 will be blocked.

fuel_sensor#_volume Fuel sensor volume
ges_radius The radius of the circular Geo-Fence region
can_total_eng_idle Total Engine Idle Time
can_eng_braking_factor Counts of braking with brake pedal or with engine
eio100_outputs 1-Wire Driver ID button
ibutton 1-Wire Driver ID button
can_cold_run_time

Total driving time with cold engine (engine coolant temperature below 70 C)

can_total_eng_hours Time of engine running since vehicle manufacture or device installation
can_axle_weight_3 Weight of vehicle’s third axle.
can_tacho_driv_direction

Vehicle driving direction from the tachograph.

0: Driving forward.

1: Driving backward.

can_rapid_accels Number of total rapid accelerations since installation
csq_rssi The network signal strength level
lon_
report Name of the report (+INF, +BNF, etc)
data_type

A hexadecimal parameter to indicate the time of the data (before crash or after crash) and crash direction (+X, -X, +Y, -Y, +Z, -Z or several of them).

lon_#
msg_type_EVT Type of +EVT or + BVT messages
bt#_dig_input_st
can_total_distance <Total Distance>: Vehicle total distance. The number is always increasing. The unit is hectometer (H)
can_total_driv_time Time of engine running (non-zero speed) since vehicle manufacture or device installation
can_total_fuel

The number of liters of fuel used since vehicle manufacture or device installation

liter
can_axle_weight_4

Weight of vehicle’s fourth axle.

can_detail_inf

It takes up two bytes. Each bit contains information of

one indicator.

Bit 0: FL – fuel low indicator (1 – indicator on, 0 – off).

Bit 1: DS – driver seatbelt indicator (1 – indicator on, 0 – indicator off).

Bit 2: AC – air conditioning (1 – on, 0 - off).

Bit 3: CC – cruise control (1 – active, 0 - disabled).

Bit 4: B – brake pedal (1 – pressed, 0 – released).

Bit 5: C – clutch pedal (1 – pressed, 0 – released).

Bit 6: H – handbrake (1 – pulled-up, 0 – released).

Bit 7: CL – central lock (1 – locked, 0 – unlocked).

Bit 8: R – reverse gear (1 – on, 0 – off).

Bit 9: RL – running lights (1 – on, 0 – off).

Bit 10: LB – low beams (1 – on, 0 – off).

Bit 11: HB – high beams (1 – on, 0 – off).

Bit 12: RFL – rear fog lights (1 – on, 0 – off).

Bit 13: FFL – front fog lights (1 – on, 0 – off).

Bit 14: D – doors (1 – any door opened, 0 – all doors closed).

Bit 15: T – trunk (1 – opened, 0 – closed).

can_lights

Each bit contains information of one particular light

Bit 0: Running Lights (1 – on, 0 – off).
Bit 1: Low Beam (1 – on, 0 – off).
Bit 2: High Beam (1 – on, 0 – off).
Bit 3: Front Fog Light (1 – on, 0 – off).
Bit 4: Rear Fog Light (1 – on, 0 – off).
Bit 5: Hazard Lights (1 – on, 0 – off).
Bit 6: Reserved.
Bit 7: Reserved.

fuel_sensor#_percent

Fuel sensor percentage

can_pedal_braking_factor

Counts of braking with brake pedal or with engine

can_doors

Each bit contains information of one door:

Bit 1: Driver Door (1 – opened, 0 – closed).

Bit 2: Passenger Door (1 – opened, 0 – closed).

Bit 3: Rear Left Door (1 – opened, 0 – closed)

Bit 4: Rear Right Door (1 – opened, 0 – closed).

Bit 5: Trunk (1 – opened, 0 – closed).

Bit 6: Boot (1 – opened, 0 – closed).

Bit 7: Reserved.

Bit 8: Reserved.

can_starts_by_ign

Total number of engine starts by ignition

can_vin Vehicle identification number
can_total_veh_ovspd

The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration

fuel_sensor#_dfs_data
bt#_an_input
speed_#
can_ad_blue_p

Ad-Blue level P-type

can_axle_weight_1

Weight of vehicle’s first axle

can_total_idle_fuel Total Idle Fuel Used
can_total_eng_ovspd The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration
bt#_temp

It indicates the temperature measured by Bluetooth accessory.

bt#_mac

The MAC address of the Bluetooth accessory

can_cold_stats

Number of cold engine starts

fuel_sensor#_temp
can_acc_pedal_press Accelerator pedal pressure
can_exp_info

Detailed Information/Indicators:
Bit 1: W – webasto (1 – on, 0 – off or not available).
Bit 2: BFL – brake fluid low indicator (1 – on, 0 – off or not available).
Bit 3: CLL – coolant level low indicator (1 – on, 0 – off or not available).
Bit 4: BAT – battery indicator (1 – on, 0 – off or not available).
Bit 5: BF – brake system failure indicator (1 – on, 0 – off or not available).
Bit 6: OP – oil pressure indicator (1 – on, 0 – off or not available).
Bit 7: EH – engine hot indicator (1 – on, 0 – off or not available).
Bit 8: ABS – ABS failure indicator (1 – on, 0 – off or not available).
Bit 9: R – reverse.
Bit 10: CHK – check engine indicator (1 – on, 0 – off or not available).
Bit 11: AIR – airbags indicator (1 – on, 0 – off or not available).
Bit 12: SC – service call indicator (1 – on, 0 – off or not available).
Bit 13: OLL – oil level low indicator.

can_reg_number The vehicle registration number
can_total_accel_kickdowns Total time when accelerator pedal is pressed over 90%
can_tacho_drv1_card_number The card number of driver 1 from the tachograph
can_tacho_drv1_name

The name of driver 1 from the tachograph

can_dtc_num

DTC (Diagnostic Trouble Code) codes are used to diagnose malfunctions in a vehicle or heavy equipment

can_tacho_inf

Two bytes. The high byte describes driver 2, and the low byte describes driver 1.

can_eng_rpm Engine speed (from CAN)
can_ad_blue_l

AdBlue Level L type

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom*
Nom*
Entreprise*
Email*
Téléphone