Traceur GPS Queclink GB100MG | Intégré à Wialon

Caractéristiques Queclink GB100MG:

2G
4G/LTE
Boîte à mémoire
BLE enabled

Afin d'identifier le boîtier Queclink GB100MG les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS:	Queclink GB100MG
ID unique:	imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GB100MG pour les utiliser dans Wialon Hosting :

Port du serveur:

22106

19658 unités Queclink GB100MG connectées au le centre de données Wialon — Ça fait 0.83% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre	Description	Unités
battery	Backup Battery Level	0-100
buffer	1 - the message is from buffer 0 - the message is from real time	0,1
cell_id	Cell tower ID
cmd_id	Sub-command ID of AT+GTRTO or the ID of AT+GTGEO (in acknowledgement to command)
crash_counter	Crash Counter
csq_ber	CSQ BER
csq_rssi	CSQ RSSI
curr_hour_meter	Ignition ON hours count (for a trip)
curr_mileage	Mileage (for a trip)
cw_jamming_val
fri_discard_no_fix
fw_ver	firmware version
geo_check_interval
geo_enable
geo_enter
geo_id
geo_mode
geo_radius
gir_trigger_type
gps_jamming_state
gps_signal_status
harsh_behavior	Harsh behavior: 0 - harsh braking behavior 1 - harsh acceleration behavior
harsh_speed_level	The speed level of which the harsh behavior is detected: 0 - unknown speed 1 - low speed 2 - medium speed 3 - high speed
head
hour_meter_count	Ignition ON hours count (total)
hw_ver	Hardware Version
iccid	ICCID
idling
ign	Ignition state: 0 - off, 1 - on
ign_duration
ign_interval
igv_interval
is_daylight_saving
jaming_status
lac	Location area code
last_fix
mask_gtbat
mask_gtgps
mcc	Mobile country code
mcu_ver
mnc	Mobile network code
motion_status
msg_type
proto_ver	Protocol Version
pwr_ext	The voltage of the external power supply
pwr_int
rep_id
rep_type
report_type	The message type of ASCII format report
response_mask
roam_state
rx_level
sats
serial_num
state
ta
text
timezone_offset
total_hour_meter
total_mileage	Total mileage
upc_result
command	Communication instructions between M1000 and devices. 0: pairing 1: Connection key setting 2: Auto arm mode setting. 3: Force arm mode setting. 4: Disarm mode setting. 5: Valet mode setting 6: Clear bonded 7: Request M1000 status	0-7
m1000_mac	M1000 MAC Address
result	The result of the device control M1000. 0: Successful. 1: Fail. 2: Disconnect From M1000. 3: Connect Key Error.	0-2
scanned_mac_N	Scanned MAC Address, N is the number of the MAC in a queue
arm_state	Optional M1000 parameter
enrolled_users_num	Enrolled Users Number(Optional)	0-5
enrolled_user	Enrolled User(Optional)
connected_key	Connected Key (Optional)	0-9
starter_relay	Starter Relay (Optional)	0\|1
m1000_mode	The current mode of the M1000. 0: Auto arm mode. 1: Force arm mode. 2: Disarm mode. 3: Valet mode.	0-3
auto_arm_delay_time	The time for auto arm delay.	sec
connection_status	The connection of M1000 with the device. 0: Disconnection
owner_mac	Owner MAC Address

Nom du paramètre

Description

Unités

battery

Backup Battery Level

0-100

buffer

1 - the message is from buffer
0 - the message is from real time

0,1

cell_id

Cell tower ID

cmd_id