Piccolo ST

Report type:

For message #224

• 1 – sharp turn
• 4 – quick acceleration
• 5 – sudden (sharp) braking
• 7 – sharp lanes crossing (direction changing)
• 8 – vehicle tilt report

For message #30

• 0 – Trip Start – 1st vehicle movement start after Engine On
• 1 – Current state – When data must be sent (PTO status changed, by time interval)
• 2 – Trip End – Engine turns off after vehicle movement
• 3 – Engine Idle Stage End – The Engine is turned off with no Vehicle movement since last Engine On
• 4 – Diagnostic report – Diagnostic code was reported by one of the JBus modules
• 6 – Response on Host request – As response on request

For message #229

• Report type 0: the tag state was changed
  o Report status = 1: the tag was connected to Piccolo Plus units
  o Report status = 0: the tag was disconnected from Piccolo Plus unit
• Report type 1: Periodic connected tag report. State data is bit masked value. The Report
  Status value bits mean the following:
  o Bit 1 (mask 0x01) – the information is sent due to timeout expired
  o Bit 2 (mask 0x02) – the information is sent due to temperature changing
  o Bit 3 (mask 0x04) – the information is sent due to A2D value changing
  o Bit 4 (mask 0x08) – the information is sent due to Input changing
• Report type 2: Current tag state sent on Host request
  o Status = 0: the tag is not connected
  o Status = 1: the tag is connected
• Report type 3: the report includes the list of connected (active) tags,
  o Is sent as an answer on Host “Rescan active Tags” or “Get Active Tags list” message. When configured this report is sent when any available input state has changed.
  o Status field must be ignore

Trip state:

• 0 – Unknown – The vehicle state was not detected yet
• 1 – Engine Off – The vehicle engine is off
• 2 – Engine starter is On – The engine is starting
• 3 – Engine On – Engine On (was successfully started), but did not move yet
• 4 – On Route – Engine On, and vehicle was moved since last Engine On

Current Engine speed, in 0.25 (implemented in Firmware version 1.85 and later)

Current Engine load, in 0.5% (implemented in Firmware version 1.85 and later)

Total fuel Used, in 0.5 liters

Driver #1 and #2 information (FW 2.99 and later).
Card info (SPN 1615 and 1616): may has one of following values:
ƒ 0 = Card not present
ƒ 1= Card present
ƒ 2 = Card Error
ƒ 3 = Information is not available

Driver #1 and #2 information (FW 2.99 and later)
o Driver work state (SPN 1612 and 1613) value means the following:
ƒ 0 = Rest - Sleeping
ƒ 1 = Driver available – short break
ƒ 2 = Work – Loading,. Unloading etc.
ƒ 3 = Drive – behind wheel
ƒ 6 = Error
ƒ 7 = information is not available

Driver #1 and #2 information (FW 2.99 and later)
o Driver time related state (SPN 1617 and 1618) value means the following:
ƒ 0 = Normal ( no limits reached)
ƒ 1 = Limit #1- 15 min before 41⁄2 hours
ƒ 2 = Limit #2 - 41⁄2 hours reached
ƒ 3 = Limit #3 - 15 min before 9 hours
ƒ 4 = Limit #4 - 9 hours reached
ƒ 5 = Limit #5 - 15 min before 16 hours
ƒ 6 = Limit #6 - 16 hours reached
ƒ 14 = Error
ƒ 15 = information is not available

Full idle time since engine on, s (FW 2.103 and later)

Idle time with parking brake on since engine on, s (FW 2.103 and later)

Engine total time of operation (FW 2.111 and later)

No. Of Active tags

Report status data

Digital Inputs state

Temperature, in 0.1 of degree

GPS Data Format Flag

Message Type:

10 - Emergency (alarm) Message

30 - J1587/J1708 Service Messages

201 - GPS Information Message

203 - IO States Report Message

224 - Acceleration alarm message

226 - Hardware Information message

228 - “No Valid GPS Fix” message

229 - WLI RF Tag Report message

248 - In Coverage Message

251 - Low Battery Message

252 - Acknowledgement Message

253 - Logout Message

254 - Login Message

Vehicle total distance