Piccolo ST

Piccolo ST
Manufacturer: Wireless Links
Forum Discussion

Number of units

3
Online
4
Total

The following data should also be added to Piccolo ST unit properties section of Wialon GPS tracking software :

Device type: Piccolo ST
Unique ID: serial

Specify the following parameters in configuration software or configuration Piccolo ST for use in Wialon Hosting :

Server port: 20318

4 units of Piccolo ST device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
mess_num Message Sequence No
rep_type

Report type:

For message #224

  • 1 – sharp turn
  • 4 – quick acceleration
  • 5 – sudden (sharp) braking
  • 7 – sharp lanes crossing (direction changing)
  • 8 – vehicle tilt report

For message #30

  • 0 – Trip Start – 1st vehicle movement start after Engine On
  • 1 – Current state – When data must be sent (PTO status changed, by time interval)
  • 2 – Trip End – Engine turns off after vehicle movement
  • 3 – Engine Idle Stage End – The Engine is turned off with no Vehicle movement since last Engine On
  • 4 – Diagnostic report – Diagnostic code was reported by one of the JBus modules
  • 6 – Response on Host request – As response on request

For message #229

  • Report type 0: the tag state was changed
    o Report status = 1: the tag was connected to Piccolo Plus units
    o Report status = 0: the tag was disconnected from Piccolo Plus unit
  • Report type 1: Periodic connected tag report. State data is bit masked value. The Report
    Status value bits mean the following:
    o Bit 1 (mask 0x01) – the information is sent due to timeout expired
    o Bit 2 (mask 0x02) – the information is sent due to temperature changing
    o Bit 3 (mask 0x04) – the information is sent due to A2D value changing
    o Bit 4 (mask 0x08) – the information is sent due to Input changing
  • Report type 2: Current tag state sent on Host request
    o Status = 0: the tag is not connected
    o Status = 1: the tag is connected
  • Report type 3: the report includes the list of connected (active) tags,
    o Is sent as an answer on Host “Rescan active Tags” or “Get Active Tags list” message. When configured this report is sent when any available input state has changed.
    o Status field must be ignore

trip_state

Trip state:

  • 0 – Unknown – The vehicle state was not detected yet
  • 1 – Engine Off – The vehicle engine is off
  • 2 – Engine starter is On – The engine is starting
  • 3 – Engine On – Engine On (was successfully started), but did not move yet
  • 4 – On Route – Engine On, and vehicle was moved since last Engine On

jbus_type JBus Type
engien_speed

Current Engine speed, in 0.25 (implemented in Firmware version 1.85 and later)

engine_load

Current Engine load, in 0.5% (implemented in Firmware version 1.85 and later)

fuel_used

Total fuel Used, in 0.5 liters

coolant_temp Coolant temperature
engine_on_tm Time since engine on, s (FW 2.103 and later)
distance_till_service Distance till next service (FW version2.99 and later)
сard#_info

Driver #1 and #2 information (FW 2.99 and later).
Card info (SPN 1615 and 1616): may has one of following values:
ƒ 0 = Card not present
ƒ 1= Card present
ƒ 2 = Card Error
ƒ 3 = Information is not available

driver#_state

Driver #1 and #2 information (FW 2.99 and later)
o Driver work state (SPN 1612 and 1613) value means the following:
ƒ 0 = Rest - Sleeping
ƒ 1 = Driver available – short break
ƒ 2 = Work – Loading,. Unloading etc.
ƒ 3 = Drive – behind wheel
ƒ 6 = Error
ƒ 7 = information is not available

driver#_state_tm

Driver #1 and #2 information (FW 2.99 and later)
o Driver time related state (SPN 1617 and 1618) value means the following:
ƒ 0 = Normal ( no limits reached)
ƒ 1 = Limit #1- 15 min before 41⁄2 hours
ƒ 2 = Limit #2 - 41⁄2 hours reached
ƒ 3 = Limit #3 - 15 min before 9 hours
ƒ 4 = Limit #4 - 9 hours reached
ƒ 5 = Limit #5 - 15 min before 16 hours
ƒ 6 = Limit #6 - 16 hours reached
ƒ 14 = Error
ƒ 15 = information is not available

parking_state Parking brake state
idle_tm

Full idle time since engine on, s (FW 2.103 and later)

idle_tm_park

Idle time with parking brake on since engine on, s (FW 2.103 and later)

engine_tm

Engine total time of operation (FW 2.111 and later)

activ_tag_num

No. Of Active tags

report_type Report Type (10.3.1 WLI RF Tag Report message, message type 229 (0xE5))
report_status_data

Report status data

tag_life_time Tag life time
link_quality Link Quality
battery_voltage Battery voltage mV
a2d_input A2D input value mV
di_state

Digital Inputs state

temp

Temperature, in 0.1 of degree

gps_data_flag

GPS Data Format Flag

int_temp Internal Temperature
pwr_int Internal battery voltage V
pwr_ext external power voltage V
ext_temp external temperature sensor C
msg_type

Message Type:

10 - Emergency (alarm) Message

30 - J1587/J1708 Service Messages

201 - GPS Information Message

203 - IO States Report Message

224 - Acceleration alarm message

226 - Hardware Information message

228 - “No Valid GPS Fix” message

229 - WLI RF Tag Report message

248 - In Coverage Message

251 - Low Battery Message

252 - Acknowledgement Message

253 - Logout Message

254 - Login Message

mileage

Vehicle total distance

in 0.1 miles

Contact Wialon and achieve the most ambitious goals with telematics

Fill out a request form to get started with Wialon

Step 1
Step 2
Step 3
First name*
Last name*
Company*
Email*
Phone