Número de unidades
The following data should also be added to RST-TG100 unit properties section of Wialon GPS tracking software :
| Device type: | RST-TG100 |
| ID único: | custom |
Specify the following parameters in configuration software or configuration RST-TG100 for use in Wialon Hosting :
| Porta do servidor: | 21068 |
286 units of RST-TG100 device type are connected to Wialon Data Center. This represents 0.01% of all AVL Hardware connected.
Below chart represents the dynamic of connections in the last 30 days:
| Parameter name | Description | Units |
|---|---|---|
| msg_type | Type 2 | |
| gps_validity | Indicates the validity of the GPS, with value 1 valid position and value 0 Invalid position. | |
| hdop | HD information of the last valid GPS position. | |
| sX_status | Status of the tracker sensors (Part 1) value. Tracker sensors in two bits: |
|
| ext_bat_status | Status of external battery (1 = conected, 0 = disconected) | |
| int_bat_status | Status of the internal battery (1 = conected, 0 = disconected) | |
| gps_ant_status | Status of the external GPS antenna (1 = conected, 0 = disconected) | |
| connect_bus_ign | Ignition status (0 = ignition off 1 = ignition on) | |
| k_sX_status | Status of the keyboard sensors value in hexadecimal. |
|
| actuators_st1 | Status of the actuators 1 tracker, value in hexadecimal. |
|
| actuators_st2 | Status of the tracker actuators 2 value in hexadecimal. |
|
| ext_bat_volt | Voltage external battery, vehicle in volts. | V |
| int_bat_volt | Voltage internal battery, tracker, in volts. | V |
| connect_bus_odom | Odometer | km |
| gsm_signal | GSM modem signal level. This value is between 0 (weak) to 31 (strongest signal). | |
| temp | For the temperature sensor, if a value of 0xFF indicates disabled sensor. Value in hexadecimal. If the value other than 0xFF, then the temperature sensor is enabled, in this case following: Bit 0 - temperature value - LSB Bit 1 - Value temperature Bit 2 - Value temperature Bit 3 - Value temperature Bit 4 - Value temperature Bit 5 - Value temperature Bit 6 - temperature value - MSB Bit 7 - Signal - if value of 1 indicates negative value if value of 0 indicates a positive value If the value is equal to 0xFE indicates that the temperature sensor is faulty hardware or not installed any temperature sensor. |
|
| seals | Status of the seals of the keyboard tracker sensors value in hexadecimal. MSB: If value 1 = 0 = sealed or unsealed Bit 0 - Sensor 3 keyboard Bit 1 - Sensor keyboard 4 Bit 2 - For future use, always 0 Bit 3 - For future use, always 0 Bit 4 - For future use, always 0 Bit 5 - For future use, always 0 Bit 6 - For future use, always 0 Bit 7 - For future use, always 0 LSB: If value 1 = 0 = sealed or unsealed Bit 0 - 1 Sensor tracker Bit 1 - Sensor 2 crawler Bit 2 - Sensor 3 crawler Bit 3 - Sensor 4 tracker Bit 4 - 5 Sensor tracker Bit 5 - Sensor 6 crawler Bit 6 - keyboard Sensor 1 Bit 7 - Keyboard Sensor 2 |
|
| crawler_status | Crawler logical status: Value 1 = switched on in ignition mode Value = 2 in ignition off mode Value = 3 in sleep mode Value = 4 in internal battery mode value = 5 in deep sleep mode (post-production) Value = 6 in breach mode Value = 7 in super sleep mode (mobile) |
|
| movement_accel | Movement accelerometer (since the accelerometer is enabled) (1 = moving or 0 = stopped) |
|
| accel_enabled | Accelerometer enabled (1 = enabled or 0 = disabled) |
|
| anti_theft_mode | Much of the Fault Codes | |
| travel_mode | Traveling mode (only when keyboard attached) (1 = 0 = way trip or stop mode) |
|
| mixer_status | Mixer status (provided it is properly configured) 000 = Not enabled 001 = Stop mixer 010 = Mixer turning left (unloading) 011 = Mixer turning right (beating the cement) 100 = Mixer cement loading 111 = Invalid State |
|
| rain_sensor | Rain sensor (provided it is properly configured) (1 = enabled or disabled = 0) |
|
| rem_fw_update | Remote Firmware Update (1 = enabled or disabled = 0) |
|
| jammer | Active Jammer and detected (1 = enabled or disabled = 0) |
|
| charger_status | Ccharger status of the internal battery 00 = no charger information 01 = loading process 10 = suspended load 11 = finished loading |
|
| event_id | Event id (for msg_type = 47) |
|
| event_paramX | Event parameters (number and meaning are based on event_id) |
|
| connect_bus_power_windows | Power windows | |
| connect_bus_spraying_sections_state | State of the spraying sections |
state |
| connect_bus_motor_load | Motor load |
% |
| connect_bus_battery_charge_state_ev | Charging type an EV |
|
| connect_bus_cooling_liquid_temp | Cooling liquid temperature |
|
| connect_bus_engine_oil_pressure | Engine oil pressure |
kPa |
| connect_bus_tire_pressure_td | The pressure of the Tire on the head | |
| connect_bus_i2_type | Type of the second input |
|
| connect_bus_fuel_type | The type of the fuel ["Methane", "Ethanol", "Diesel"] |
|
| connect_bus_app_volume_rate | The rate of the Volume of the App, for HA |
|
| connect_bus_alarm | Alarm | |
| connect_bus_water_in_fuel | The indicator of the Water-In-Fuel sensor: Off, On |
state |
| connect_bus_cotton_platform | Platform cotton state: Down Lower, Rising |
|
| connect_bus_i2_value | Value of the second input |
V |
| connect_bus_motor_torque | Motor torque |
Nm |
| connect_bus_battery_health_ev | Battery health (EV) |
|
| connect_bus_o2_signal | Signal of the second output ["Disabled", "Digital", "Digital" inverted", "RANGE"] |
signal |
| connect_bus_cane_elevator_treadmill | State of the cane elevator treadmill ["Off", "On"] |
|
| connect_bus_motor_torque_percentage | Torque motor percentage |
% |
| connect_bus_water_pump_sprayer | Water pump sprayer state |
|
| connect_bus_o2_type | The type of the second output |
|
| connect_bus_fuel_flow | Total fuel flow |
(l/h) |
| connect_bus_passenger_door | Passenger door state (EV) |
|
| connect_bus_pump_to_diesel_flow | The flow from the Pump to a Diesel |
|
| connect_bus_clutch_pedal | Clutch pedal state |
|
| connect_bus_acc_pedal | Accelerator pedal pressure |
% |
| connect_bus_door_passenger | State of the passenger door |
|
| connect_bus_air_conditioning_pwr_ev | The power of the Air-Conditioning system (IV) | |
| connect_bus_liquid_release_spray | ["Off", "On"] | |
| connect_bus_cane_production | ["Off", "On"] |
|
| connect_bus_battery_average_savings_ev | Average savings of Battery power (EV) | |
| connect_bus_pto | PTO active |
|
| connect_bus_gear | Gear | march |
| connect_bus_electric_motor_temp_ev | The temperature of the Electric Motor (EV) | °C |
| connect_bus_fault_codes_amount | Fault codes amount |
|
| connect_bus_heater_pwr_ev | The power of the Heater (EV) |
|
| connect_bus_msg_type | Message type |
|
| connect_bus_fuel_level | Fuel Level |
% |
| connect_bus_oil_engine_pressure | The pressure of the engine oil |
|
| connect_bus_e_pedal | E-pedal State (EV) |
|
| connect_bus_tire_pressure_te | Tire pressure (TE) |
Psi |
| connect_bus_cotton_harvesting_unit | Cotton harvesting state |
|
| connect_bus_charging_cable_ev | A Charging cable is Plugged in (EV) | |
| connect_bus_brake_time | Time to brake |
s |
| connect_bus_headlights | The state of the lights | |
| connect_bus_speed_ev | Vehicle speed (EV) |
|
| connect_bus_coupler_back | position of the coupler back |
% |
| connect_bus_tire_pressure_de | Tire pressure DE |
|
| connect_bus_o2_value | Value of the second output |
|
| connect_bus_cotton_packer | Cotton packer state |
|
| connect_bus_brake_parking | Brake, Parking |
|
| connect_bus_electric_motor_current_ev | Electric motor current (EV) |
|
| connect_bus_airbag | Airbag state |
|
| connect_bus_arla32_level | ARLA32 level |
|
| connect_bus_dtc_present | ["No fault", "fault"] |
|
| connect_bus_lever | State of the lever |
|
| connect_bus_rtk_autopilot | State-BASE / Auto-Pilot |
|
| connect_bus_eng_on_dur | Duration of engine on |
|
| connect_bus_engine_rpm | Revolutions per minute of the engine |
rpm |
| connect_bus_int_resist | Resistance of internal battery |
V |
| connect_bus_hitch_to_front | Position of hitch to the front |
% |
| connect_bus_load_speed | Load speed of the motor |
|
| connect_bus_seatbelt_passenger | Seatbelt, Driver |
|
| connect_bus_i1_value | Value of the first input |
|
| connect_bus_ign_on_duration | Duration of Ignition On |
|
| connect_bus_air_temp | Air temperature |
|
| connect_bus_intake_air_pressure | Intake air pressure |
|
| connect_bus_blink_warning | Blink warning ["Off", "On"] |
|
| connect_bus_clutch | Clutch switch |
|
| connect_bus_engine_brake_mode | Engine brake mode:
|
|
| connect_bus_out_turbo_oil_temp | Oil temperature in turbo |
°C |
| connect_bus_right_rear_door | ["Open", "Closed", "Locked"] | |
| connect_bus_charging_type_ev | ["Not Loading", "Slow Loading", "Fast Loading"] |
|
| connect_bus_o1_type | ["Generic", "Lock", "Lock box", "Relay-L15", "Siren"] |
|
| connect_bus_battery_life_ev | Battery life (EV) |
|
| connect_bus_lambda | ||
| connect_bus_time_to_charge_80 | The time of 80% charge (EV) |
h |
| connect_bus_seatbelt_driver | State of the driver's seatbelt |
|
| connect_bus_charging_voltage_ev | Charging voltage type (EV) |
State |
| connect_bus_eco_mode | Eco-mode state (EV) |
|
| connect_bus_intake_manifold_temp | Engine Intake Manifold 1 Temperature |
|
| connect_bus_door_driver | State of the driver's door |
|
| connect_bus_primary_air_pressure | Pressure In The Air Reservoir, The Primary |
|
| connect_bus_trans_oil_temp | Transmission oil temperature |
°C |
| connect_bus_fuel_temp | Fuel temperature |
°C |
| connect_bus_primary_air_reservoir_pressure | The pressure of the Air in the Reservoir, the Primary | |
| connect_bus_pwr_int | Internal voltage |
V |
| connect_bus_engine_hours | Total engine hours |
|
| connect_bus_air_conditioning_temp | The Selected temperature of the Air-Conditioning system | °C |
| connect_bus_current_battery_capacity_ev | The Current capacity of the Battery (EV) | |
| connect_bus_speed | The speed determined by the tachograph |
|
| connect_bus_pwr_int_ev | Interval power voltage |
|
| connect_bus_oil_hydraulic_temp | Oil hydraulic temperature |
|
| connect_bus_grain_unloading | ["Off", "On"] |
|
| connect_bus_wiper_blade | Wiper Blade for windshield |
|
| connect_bus_trunk | ["Open", "Closed", "Locked"] |
|
| connect_bus_full_charge_time_ev | Charge time to full (100%) (EV) |
|
| connect_bus_payload_ver | Version of the payload like 1.2.3 |
|
| connect_bus_traction | Traction |
|
| connect_bus_left_rear_door | ["Open", "Closed", "Locked"] |
|
| connect_bus_eng_oil_level | Oil level in engine |
% |
| connect_bus_distance_to_service | Distance to the Service | |
| connect_bus_battery_output_pwr_ev | Battery voltage (EV) |
|
| connect_bus_i1_signal | Signal of the first input |
|
| connect_bus_i2_signal | Signal of the second input |
|
| connect_bus_tire_pressure_dd | Tire pressure (DD) |
Psi |
| connect_bus_o1_value | Value of output 1 |
V |
| connect_bus_clutch_time | Time to clutch |
|
| connect_bus_engine_brake | Engine brake state |
|
| connect_bus_load_code | Load code |
|
| connect_bus_turbo_pressure | Turbo pressure |
Nm |
| connect_bus_angle | The angle of the steering Wheel |
° |
| connect_bus_tank_ethanol_percentage | Percentage of Ethanol in the Tank | |
| connect_bus_maximum_battery_capacity_ev | The Maximum capacity of the Battery (EV) | |
| connect_bus_i1_type | Type of the input 1 |
|
| connect_bus_instant_savings | Instant savings |
|
| connect_bus_odometer | Hour meter | km |
| connect_bus_nitrogen_oxides_nox | Nitrogen oxides (Nox) |
ppm |
| connect_bus_average_savings | Average savings |
|
| connect_bus_court_pressure | Court pressure |
|
| connect_bus_primary_cane_extractor | State of the cane extractor |
|
| connect_bus_total_fuel | Total fuel used |
l |
| connect_bus_battery_temp_ev | Temperature of the battery (EV) |
|
| connect_bus_air_conditioning | ["Off", "On"] |
|
| connect_bus_o2_percentage | O2 Percentage |
|
| connect_bus_eng_oil_temp | Engine oil temperature |
|
| connect_bus_available_regeneration_pwr_ev | Available regeneration power (EV) |
|
| connect_bus_the_modes_of_the_engine_brake | Modes of the engine brake |
|
| connect_bus_brake_pedal | Brake pedal state |
|
| connect_bus_o1_signal | Signal of the output 1 |
|
| connect_bus_proto_ver | Connect bus protocol version: v1 or v4 |
|
| rf433_state | RF module status: |
|
| delivery_time | The time of activation of the current module |
s |
| last_activation_id | The ID of the last of the activation, and if the value is equal to: |
|
| last_tombstone_id | The ID of the last shutdown, if the value is equal to: |
|
| melody | The kind of song that, if the value is equal to: |
|
| comm_frequency | The value of the frequency of communication: RF |
|
| ext_analog_reader | Information of the reader, external analog |
|
| max_speed_gps | The value of the maximum speed of the GPS between the message tracking (position) |
|
| fuel_system_status | If the value is 0, The motor is switched off |
|
| motor_load | Percentage or of the load current of the motor (from 0 up to 100%) |
% |
| cooling_liquid_temp | The current value of the temperature of the liquid coolant in the engine |
|
| fuel_pressure | The current value of the pressure in the fuel you need to multiply by 3 to get the value |
kPa |
| rpm | The current value of the RPM of the engine |
|
| speed | The current value for the speed of the vehicle |
|
| distance_indicator | Current value-led in the distance traveled (the information that is available only on the protocol (OBD2) | |
| fuel_level | The current value of the level of the fuel tank | |
| engine_oil_temp | The current value of the temperature of the oil in the motor |
|
| clearing_codes_dist | The current value of the distance from the cleaning up of the code information is available to you only on the protocol (OBD2) |
|
| odometer | The current odometer | |
| room_temp | The current value of the ambient temperature | |
| total_fuel_used | The current value of your total fuel used, source of information that is available only for internet protocol J1939) |
|
| fuel_economy | The current value of the economy, instant fuel source of information that is available only for internet protocol J1939) |
|
| acc_pedal | The current value of the position of the accelerator pedal (the information is only available for internet protocol J1939) |
|
| brake_pedal | The current value of the position of the brake pedal (the information is only available for internet protocol J1939) |
|
| torque | The current value of the torque of information that is available only for internet protocol J1939) |
|
| reverse_current | The current value of the reverse current information that is available only for internet protocol J1939) |
|
| total_engine_hours | Accumulated time of operation of the engine (the information is only available for internet protocol J1939) |
|
| add_info2 | The formatted value in the hex containing the bits to the additional information in part 2 |
|
| sysconfig | The current value of the range, the message will be sent the tracking information on the sleep that is used by the crawler |
|
| prev_sysconfig | The value of the previous range, the message will be sent multiple tracking in sleep |
|
| sysconfig_change_ts | The Timestamp of the last change in the value of the setting range, the message will be sent the tracking is in the sleep |
|
| max_rpm | The value of the RPM to the maximum measured during the interval of the delivery of the message tracking |
|
| min_rpm | The value of the RPM to the minimum measured during the interval mum of the delivery of the message tracking |
|
| avg_rpm | The value of RPM is the average measured at the interval of the delivery of the message tracking |
|
| comm_tech | The value of the communication technologies |
|
| hour_meter_ign_on | The total amount of the tracer when the ignition is switched on | s |
| rf_sn | The serial number read from the tracker or the height of a lock to the RF that is configured as a master or a slave that is connected to this tracker |
|
| rf_fw_version | The current version of the firmware of the module |
|
| actuator_status_tracker | The Status of the actuator, a value that is in hexadecimal |
|
| actuator_status_keypad | The Status of the actuator, a value that is in hexadecimal |
|
| cumul_hour_meter_tristate_X | The time is measured to the hour meter from 0 to 4294967295 |
s |
| cumul_hour_meter_wrist_X | The time is measured to the hour meter from 0 to 4294967295 |
s |
| cumul_hour_meter_digital_X | The time is measured from the hour meter 0 to 4294967295 |
s |
