| va |
People counting, current onbus people number byte is valid or not (device calculated), 0-invalid, 1-valid |
|
| event_type |
Event type code: 0-unknown, 1-video lost, 2-motion detection, 3-video blind, 4-input trigger, 5-emergency alarm, 6-low speed alarm, 7-over speed alarm, 8-low temperature alarm, 9-high temperature alarm, 10-humidity alarm, 11-parking over time, 12-acceleration alarm, 13-GEO fencing, 14-electronic route, 15-abnormal openclose the door, 16-storage abnormal, 17-fatigue driving, 18-fuel consumption abnormal, 19-illegal ACC, 20-GPS module abnormal, 21-front panel open, 22-Swipe card, 23-IBUTTON, 24-Harsh acceleration, 25-Harsh braking, 26-Low speed warning, 27-High speed warning, 28-Voltage alarm, 29-People counting, 30-ADAS alarm, 31-"Acc on" (report once at boot), 32-Idle, 33-Gps antenna break, 34-Gps antenna short, 35-IO output, 36-CAN Bus connection abnormal, 37-Towing, 38-Free wheeling, 39-RPM exceeds, 40-Vehicle Move, 41-Trip start, 42-In trip, 43-Trip ends, 44-GPS location recover, 45-Video abnormal, 768-Trip notification, 769-Upgrade notification |
|
| I/O |
1-Close, 2-Emergency, 3-Front door, 4-Middle door, 5-Back door, 6-Dipped headlight (near light), 7-High beam (far light), 10-Right turn light, 11-Left turn light, 12-Brake, 13-Back a vehicle, 14-(Reserved), 15-The front door close, 16-The middle door close, 17-The back door close, 18-Intercom, 19-Lifting, 20-Seal, 21-Loading, 23-Customer define, 24-Safe to load, 32-Ibutton2 |
|
| in_veh_temp |
Temperature in vehicle |
|
| video_loss |
bit0 - channel 1 video loss indicator (0: no video loss, 1: video loss); bit1 - channel 2; bit2 - channel 3; etc. |
|
| cnt_lat |
People counting latitude |
|
| geofence_threshold |
The speed value alarm value. Valid when geofence_status = 2 or 4 |
Km/h |
| alarm_et |
Event end time |
|
| mb |
mobile phone number |
|
| position_accuracy |
Positioning accuracy |
m |
| gsensor_impact |
GSensor impact |
g |
| swipe_card_rvrsd |
Card number, etc. |
|
| driver_data |
Driver info |
|
| at |
Access network. 1-Ethernet 2-WIFI 3-2G |
|
| ssid |
Wi-Fi ssid |
|
| fn |
file path. For example, "/mnt/sd1/xxxx.264" |
|
| alc_concentr |
Alcohol concentration |
mg/100ml |
| cur_mileage |
Current day mileage |
meter |
| video_type |
video type: video/mp4 |
|
| wifi_gateway |
Wi-Fi gateway address |
|
| total_mileage |
Total mileage |
meter |
| location_type |
Location type. 0—location invalid; 1--GPS; 2--BD; 3--Glonass; 4--AGPS; 5--base station location; 6 - WIFI |
|
| obd_air_press_N |
Intake pressure in Kpa |
|
| wifi_module |
WIFI module. 0--unknown 1--normal 2--abnormal 3—not exist |
|
| wifi_net_addr |
Wi-Fi network address |
|
| dt |
Device Type |
|
| mt |
Media Type. 1-live view 2-playback 3-audio 4-file transmission 5-serial transmission |
|
| dw0 |
The number of offbus people, <0 means invalid |
|
| sc_ht |
Swipe card information. History: 1 — Historical data; 2 — Real time data; Else — invalid |
|
| trigg_threshold |
Trigger threshold |
mg/100ml |
| swipe_card |
Swipe card number |
|
| y_accel |
GSensor acceleration, Y axis |
g |
| geofence_status |
Values description: 0-enter, 1-exit, 2-over-speed alarm, 3-over-speed warning, 4-low speed alarm, 5-low speed warning, 6-forbidden parking engine star, 7-forbidden parking engine off, 8-overtime stay in geofence, 9-Pre-entry, 10-Pre-exit |
|
| max |
Acceleration alarm, Maximum value during the alarm |
|
| obd_i_fuel_cons_N |
Instant fuel consumption in L/km |
|
| obd_rpm_N |
Engine speed in rpm |
|
| alarm_inputs |
Alarm inputs triggered: bit0 - input 1; bit1 - input 2; etc. |
|
| out_veh_temp |
Temperature outside of vehicle |
|
| alarm_st |
Event start time |
|
| ft |
file type: 0-unknown, 1-general recording, 2-alarm recording, 3-general snapshot file, 4-alarm snapshot file, 5-upgrade file, 6-log file, 7-Configuration file, 8-Black box file, 9-Visible alarm video/snapshot |
|
| dw1 |
The number of offbus people, <0 means invalid |
|
| obd_int_temp_N |
Intake air temperature |
|
| obd_cool_temp_N |
Coolant temperature |
|
| in_veh_hum |
Humidity in vehicle |
|
| ver |
Current version of device |
|
| cnt_tm |
People counting time |
|
| motor_temp |
Motor temperature |
|
| obd_thr_pos_N |
Throttle position in % |
|
| voltage_N |
Vehicle voltage. Double value, in V. |
|
| obd_rem_oil_N |
Remaining oil in % |
|
| out_veh_hum |
Humidity outside of vehicle |
|
| cur |
Acceleration alarm, Current value when reporting |
|
| wifi_subnet |
Wi-Fi subnet mask |
|
| ibutN |
iButton code. N - iButton number |
|
| err |
Error code: 0 Success, 1 Duplicated ID, 2 invalid parameter, 3 invalid command, 4 device busy, 5 connection lost, 6 related file not exist, 7 disk not exist, 8 follow up data, 9 file search finish, 10 Device is not authorized, 255 Unknown error |
|
| min |
Acceleration alarm, Minimum value in a period |
|
| hdN_capacity |
Hard disk N (disk index) balance capacity |
Mega Bytes |
| filetype |
0-unknown, 1-general recording, 2-alarm recording, 3-general snapshot file, 4-alarm snapshot file, 5-upgrade file, 6-log file, 7-Configuration file, 8-Black box file, 9-Visible alarm video/snapshot |
|
| drid |
Driver ID |
|
| pat |
People counting. 0-real time; 1-stored and forward (data was resent after network works) |
|
| cnt_lon |
People counting longitude |
|
| pre |
Acceleration alarm, The value of one second before |
|
| x_accel |
GSensor acceleration, X axis |
g |
| ts |
Transmission Status: 1-Start, 0-End |
|
| mob_signal |
Mobile signal intensity |
|
| video_uri |
video URI |
|
| adas_alarm_type |
ADAS: 1-Forward collision alarm, 2-Lane departure warning, 3-Car distance too near, 4-Pedestrian collision alarm, 5-Frequent lane change alarm, 6-Road sign violate alarm, 7-Harsh Acceleration, 8-Harsh Breaking, 9-Safety Distance, 16-Traffic Sign Recognition, 17-FCW: Forward collision warning, 18-HMW: Headway monitoring warning, 19-Left Lane departure warning, 20-Right Lane departure warning, 21-VB Forward Collision Warning. DMS: 33-Fatigue driving alarm, 34-Phone call alarm, 35-Smoking alarm, 36-Distracted driving alarm, 37-Driver abnormal alarm, 49-Driver change event, 65-Eye closed, 66-Yawning, 67-Camera cover, 68-Distracted Driving, 69-Seat belt not fastened, 70-No driver, 72-Driver shift, 73-Driver back, 80-Infrared sunglasses, 81-Driver ID identified successfully, 82-Driver ID identified failed, 83-No Driver face detected, 85-Mask not worn |
|
| gsensor_tilt |
GSensor tilt |
g |
| mob_net_type |
Mobile network type: 0 - unknown; 3 - 2G; 4 - 3G; 5 - 4G; 6 - 5G |
|
| device_temp |
Device temperature |
|
| ap |
The hotspot when MDVR connects to the sever in WiFi mode. |
|
| modem_status |
Satellite Modem Status: 0-Working normal, 1-Module normal, satellite communication abnormal, 2-Module abnormal |
|
| status1 |
bit0 - ACC (0-invalid,1-valid); bit1-break (0-invalid, 1-valid); bit2 - turn left (0-invalid,1-valid); bit3 - turn right (0-invaid,1-valid); bit4 - forward (0-invalid, 1-valid); bit5 - backword (0-invalid,1-valid); bit6 - left front door (0-Close,1-Open); bit7 - right front door (0-close,1-Open) |
|
| alarms |
Alarm status: bit0—video loss; bit1—motion detection; bit2—video blind; bit3—alarm input trigger; bit4—over speed alarm; bit5—low speed alarm; bit6—emergency alarm; bit7—over time stop; bit8—vibration alarm; bit9—out of GEO fencing alarm; bit10—enter GEO fencing alarm; bit11—exist line alarm; bit12—enter line alarm; bit13—fuel level alarm |
|
| hdN_status |
Hard disk N (disk index) status: 0 - unknown; 1 - recording; 2 - idle; 3 - abnormal; 4 - full |
|
| gsensor_status |
GSensor status. 0--unknown 1--normal 2--abnormal 3—not exist |
|
| bluetooth_data |
Bluetooth status: 0-not connected, 1-connected |
|
| balance_fuel |
Balance fuel |
|
| sc_up |
Swipe card information. Onboard/offboard: 1 — Onboard (check in); 2 — Off board (check out); Else — invalid |
|
| device_tm |
Event device time |
|
| up0 |
The number of onbus people, <0 means invalid |
|
| hdN_size |
Hard disk N (disk index) size |
Mega Bytes |
| text |
information message |
|
| up1 |
The number of onbus people, <0 means invalid |
|
| fuel_cons |
Fuel consumption |
|
| ch |
Media channel. starting from 1, 0 means no need for the channel. |
|
| wifi_signal |
Wi-Fi signal intensity |
|
| recording_status |
Bit0 - channel 1 is recording; Bit1 - channel 2 is recording; Bit2 - channel 3 is recording; Bit3 - channel 4 is recording; Bit4 - channel 5 is recording; etc. |
|
| dt_ |
Acceleration alarm, direction: 1-X direction, 2-Y direction, 3-Z direction, 4-impact, 5-tilt, 6-turn |
|
| gps_module |
GPS location module. 0--unknown 1--normal 2--abnormal 3—not exist |
|
| status2 |
bit0 - left mid door (0-close, 1-open); bit1 - right mid door(0-close, 1-open); bit2 - left back door(0-close, 1-open); bit3 - right back door(0-close, 1-open) |
|
| video_blind |
Video blind: bit0 - channel 1; bit1 - channel 2; etc. |
|
| z_accel |
GSensor acceleration, Z axis |
g |
| tt |
Acceleration alarm, time threshold |
|
| obd_t_mil_N |
Accumulated mileage in km. |
|
| vt |
Acceleration alarm, trigger threshold |
|
| drname |
Driver name |
|
| motion |
Motion detection: bit0 - channel 1; bit1 - channel 2; etc. |
|
| obd_t_fuel_cons_N |
Cumulative fuel consumption in L. |
|
| filename |
Corresponding file name of recording file. It is usually used in alarm recording playback, and start time/end time is invalid in this mode. |
|
| obd_eng_load_N |
Engine load in % |
|
| mobile_net |
Mobile network. 0--unknown 1--normal 2--abnormal 3—not exist |
|
| alarm_ec |
Event type code: 0-unknown, 1-video lost, 2-motion detection, 3-video blind, 4-input trigger, 5-emergency alarm, 6-low speed alarm, 7-over speed alarm, 8-low temperature alarm, 9-high temperature alarm, 10-humidity alarm, 11-parking over time, 12-acceleration alarm, 13-GEO fencing, 14-electronic route, 15-abnormal openclose the door, 16-storage abnormal, 17-fatigue driving, 18-fuel consumption abnormal, 19-illegal ACC, 20-GPS module abnormal, 21-front panel open, 22-Swipe card, 23-IBUTTON, 24-Harsh acceleration, 25-Harsh braking, 26-Low speed warning, 27-High speed warning, 28-Voltage alarm, 29-People counting, 30-ADAS alarm, 31-"Acc on" (report once at boot), 32-Idle, 33-Gps antenna break, 34-Gps antenna short, 35-IO output, 36-CAN Bus connection abnormal, 37-Towing, 38-Free wheeling, 39-RPM exceeds, 40-Vehicle Move, 41-Trip start, 42-In trip, 43-Trip ends, 44-GPS location recover, 45-Video abnormal, 768-Trip notification, 769-Upgrade notification, 1280-Alarm file, 281-Timer Snapshot, 1282-Alarm file (in visible partition), 1283-ftp file upload notification |
|
| obd_speed_N |
speed, needs *100 for km/h |
|
| avg |
Acceleration alarm, Average value in a period |
|
| obd_pwr_N |
Vehicle voltage in V |
|
| obd_air_flow_N |
Intake air flow in G/s |
|
