| RFID |
RFID code |
|
| event_code |
Event Code |
|
| valid |
GPS status |
|
| gsm_signal |
GSM signal |
|
| hdop |
Horizontal Dilution of Precision |
|
| mileage |
Total accumulated mileage |
km |
| engine_hours |
Total accumulated runtime |
|
| battery |
battery charge |
V |
| pwr_ext |
Voltage of external power supply |
V |
| fuel_percent |
Percentage of remain fuel |
% |
| temp_N |
Temperature sensor N value |
°C |
| wln_accel_max |
Maximum acceleration value |
g |
| wln_brk_max |
Maximum deceleration value |
g |
| lls_N_temp |
LLS fuel sensor N temperature
|
°C |
| lls_N_val |
LLS fuel sensor value
|
|
| lls_N_freq |
LLS fuel sensor frequency
|
|
| dr_f_status |
Driver fatigue alert:
- 01 - Mild fatigue
- 02 - Moderate fatigue
- 03 - Severe fatigue
- 04 - Distraction alert
- 05 - Absence alert
- 06 - On Phone Call alert
- 07 - Smoking alert
- 08 - Yawning alert
|
|
| ignition |
Ignition status |
|
| tire{tire_id}_loc |
Tire position
Tire position：7~5bit indicate the vehicle
head or trailer：000(B): Vehicle head，
001(B):Trailer 1，010(B): Trailer 2，
011(B): Trailer 3，100(B): Trailer 4，
4~0bit indicate the tire number：For
example, 00001(B), indicating the first tire
|
|
| tire{tire_id}_press |
Tire pressure value:
Formula :obtained
value x 0.025
|
bar |
| tire{tire_id}_temp |
Tire temperature value:
Formula: obtained value – 50
|
°C |
| tire{tire_id}_alert |
Tire status:
Bit7: indicates the battery voltage
status of the transmitter. 0: normal voltage;
1: low voltage.
Bit6：Whether to receive data from
the transmitter. If you do not receive data
from the transmitter within 15 minutes, the
parameter value will be reset to 1.
Bit5：reserved.
Bit4：When the value is 1, the air
pressure is high.
Bit3：When the value is 1, the air
pressure is low
Bit2：indicates temperature status. 1:
high temperature; 0: normal temperature.
Bit1~Bit0：indicates the alert status.
00: no alert; 01: fast air leak alert; 10: slow air
leak alert; 11: tire inflation alert.
|
|
| system_flag |
System Flag:
Bit 0: Whether to modify the EEP2 parameter.
When the parameter value is 1, the EEP2
parameter is modified.
Bit 1: Indicates the ACC status. When the
parameter value is 1, the ACC is on.
Bit 2: Indicates the anti-theft status. When the
parameter value is 1, the tracker is in the
arming state.
Bit 3: vibration flag. When the parameter value
is 1, the tracker is vibrating.
Bit 4: moving flag. When the parameter value is
1, the tracker is moving.
Bit 5: Whether to connect the external power
supply. When the parameter value is 1, the
external power supply is connected.
Bit 6: Whether the tracker is charging. When
the parameter value is 1, the tracker is
charging.
Bit 7: Whether to enable the sleep mode.
When the parameter value is 1, the sleep mode
is enabled.
Bit 8: Whether to connect the FMS. When the
parameter value is 1, the FMS is connected.
Bit 9: Whether to enable the FMS function.
When the parameter value is 1, the function is
enabled.
Bit 10: Whether to connect the Mobileye.
When the parameter value is 1, the Mobileye is
disconnected.
Bit 11: Whether to connect the Mobileye.
When the parameter value is 1, the Mobileye is connected.
Bits 12–31: reserved.
|
|
| outputs_status |
Indicates the status values of eight output
ports.
Bits 0–7 correspond to status of output ports
1–8. |
|
| inputs_status |
Indicates the status values of eight Input ports.
Bits 0–7 correspond to status of Input ports 1–
8. |
|
| geo_fance_number |
Number of Geo-fence |
|
| clutch_switch |
Clutch switch:
0: The clutch pedal is released
1: The clutch pedal is pressed.
|
|
| park_brake |
Parking brake
switch:
0: Do not apply the brake.
1: Apply the brake.
|
|
| cruise_cnt |
Cruise control
system:
0: The cruise control system is switched off.
1: The cruise control system is switched on.
|
|
| acc_pedal |
Accelerator
pedal position |
% |
| can_fuel_lvl |
CAN bus fuel
level |
% |
| fuel_level_proc |
Fuel level, should be divided by 100 |
% |
| veh_speed_taho |
Vehicle speed
(based on the
tachograph) |
km/h |
| veh_speed_wheel |
Vehicle speed
(based on the
wheel) |
km/h |
| engine_speed |
Engine speed |
rpm |
| eng_cool_temp |
Engine coolant
temperature |
°C |
| run_time |
Run time |
h |
| total_fuel_cons |
Total fuel
consumption |
l |
| total_eng_run_tm |
Total engine
run time |
h |
| high_res_veh_dist |
High
resolution
vehicle
distance |
m |
| service_dist |
Service
distance |
km |
| axle_weight |
Axle weight |
kg |
| sens{ind_sens} |
Temperature
sensor {ind_sens} value
|
°C |
| accel_x |
Indicates the instantaneous acceleration of the
XYZ axis when a crash alarm is triggered |
mg |
| accel_y |
Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered |
mg |
| accel_z |
Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered |
mg |
| mobileye_alm |
Mobileye alarm
2-byte hexadecimal data
little-endian
The data is available only when the GPRS event
code is 93
Bit0: Forward Collision Warning (FCW)
Bit1: Urban Forward Collision Warning (UFCW)
Bit2: Pedestrian Collision Warning (PCW)
Bit3: Left Lane Departure Warning (LLDW)
Bit4: Right Lane Departure Warning (RLDW)
Bit5: Headway Monitoring and Warning (HMW)
Bit6: Speed Limit Indicator (SLI)
Data type: WORD
|
|
