| report_id |
Report ID
|
(not set) |
| report_type |
Report Type
|
(not set) |
| mcc |
Mobile country code
|
(not set) |
| mnc |
Mobile network code
|
(not set) |
| lac |
Location area code in hex format
|
(not set) |
| cell_id |
Cell ID in hex format
|
(not set) |
| csq_rssi |
The signal strength level
|
(not set) |
| csq_ber |
The quality of the signal
|
(not set) |
| battery_remaining |
The estimated battery’s remaining life
|
days |
| battery |
Current volume of the battery in percentage
|
% |
| battery_voltage |
Battery voltage
|
V |
| fri_mode |
FRI Mode
|
(not set) |
| movement_status |
The movement status of the device 0: stillness 1: Motion
|
(not set) |
| temp_int |
The real time temperature value of the device
|
°C |
| phone_number |
The phone number which initiates this report
|
(not set) |
| iccid |
The ICCID of the installed SIM card
|
(not set) |
| total_pac |
The total number of messages.
|
(not set) |
| curr_pac |
The sequence number of the current message
|
(not set) |
| config |
The current configurations of the device
|
(not set) |
| time_zone |
Time zone
|
(not set) |
| daylight_saving |
Daylight Saving
|
(not set) |
| apn |
APN
|
(not set) |
| apn_username |
APN User Name
|
(not set) |
| apn_password |
APN Password
|
(not set) |
| backup_apn |
Backup APN
|
(not set) |
| backup_apn_username |
Backup APN User Name
|
(not set) |
| backup_apn_password |
Backup APN Password
|
(not set) |
| ip_address |
IP Address
|
(not set) |
| main_dns |
Main DNS
|
(not set) |
| backup_dns |
Backup DNS
|
(not set) |
| network_type |
Network Type
|
(not set) |
| sv_id_[i] |
The satellite ID
|
(not set) |
| sv_power_[i] |
Satellite power
|
(not set) |
| ati_mask |
ATI Mask
|
(not set) |
| soft_ver |
The firmware version of the device
|
(not set) |
| mcu_soft_ver |
The MCU firmware version of the device
|
(not set) |
| modem_soft_ver |
The Modem software version of the device
|
(not set) |
| hard_ver |
The hardware version of the device
|
(not set) |
| modem_hard_ver |
The Modem hardware version of the device
|
(not set) |
| sensor_id |
It indicates the type of the sensor currently used by the device
|
(not set) |
| power_on_type |
A numeral to indicate how the device is activated. - Reserved
- Reserved
- Reserved
- Manual power on with the key button for the first time
- RTO command or watchdog reboot
- Abnormal power on
- RTC error
- FOTA process
- Reserved
- Reset PIN
|
(not set) |
| event_state_1 |
The temperature alarm state - The current temperature is lower than the low temperature threshold specified
by Min. Temperature.
- The current temperature is higher than the high temperature threshold
specified by Max. Temperature .
- The current temperature is within the temperature threshold range.
- The current temperature is outside the temperature threshold range.
|
(not set) |
| event_state_2 |
Event state 2 |
(not set) |
| light_level |
The level of light intensity detected by the device
|
(not set) |
| trigger_type |
A string which indicates the type of GNSS fix this cell information is
for. "FRI": This cell information is for FRI request. "RTL": This cell information is for RTL request. "GIR": This cell information is for GIR request
|
(not set) |
| mcc[i] |
MCC of the neighbor cell i
|
(not set) |
| mnc[i] |
MNC of the neighbor cell i
|
(not set) |
| lac[i] |
LAC of the neighbor cell i
|
(not set) |
| cell_id[i] |
Cell ID of the neighbor cell i
|
(not set) |
| rx_level[i] |
The signal strength of the neighbor cell i 0: -110 dBm 1 to 62: -109 to -48 dBm 63: -47 dBm
|
(not set) |
| command_id |
The command ID in the update configuration file.
|
(not set) |
| result |
A numeral to indicate whether the configuration is updated successfully. - 100: The update command is starting.
- 101: The update command is confirmed by the device.
- 102: The update command is refused by the device.
- 103: The update process is refused because the battery is low.
- 200: The device starts to download the package.
- 201: The device finishes downloading the package successfully.
- 202: The device fails to download the package.
- 300: The device starts to update the device configuration.
- 301: The device finishes updating the device configuration successfully.
- 302: The device fails to update the device configuration.
- 305: The update process is interrupted by reboot.
- 306: The update process is interrupted by MD5 verification error.
|
(not set) |
| url |
The complete URL to download the configuration. It includes the
file name.
|
(not set) |
| id_number |
Identifier Number
|
(not set) |
| last_mode |
The working mode of the fixed report function. - 0: Quick track
- 1: Standard track
- 2: Recovery track
- 3: Disable.
|
(not set) |
| new_mode |
The working mode of the fixed report function. - 0: Quick track
- 1: Standard track
- 2: Recovery track
- 3: Disable.
|
(not set) |
| config_ver |
Config Version
|
(not set) |
