Queclink GL30MG

Fabricante: Queclink Wireless Solutions

Forum Discussion

Número de unidades

ON-LINE

TOTAL

Features Queclink GL30MG:

2G
4G/LTE

Supported in Wialon:

Gerenciamento remoto via GPRS
Gerenciamento remoto via SMS
Comunicação via TCP
Comunicação via UDP

The following data should also be added to Queclink GL30MG unit properties section of Wialon GPS tracking software :

Device type:	Queclink GL30MG
ID único:	imei

Specify the following parameters in configuration software or configuration Queclink GL30MG for use in Wialon Hosting :

Porta do servidor:

22659

25 units of Queclink GL30MG device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name

Description

Units

temp_int

The real time temperature value of the terminal. It must be noted that the
temperature function must be enabled in the in the AT+GTTEM command, otherwise this field is empty

rx_level

The network signal strength level. The range is 0-31, and 99 is for unknown signal strength

avl_driver

The id number of the driver represented in decimal format

active_mode

Current mode of the device.
0: Power saving mode (PSM)
1: Continuous mode

battery

Current volume of the battery

cell_id

Cell ID (CID) is a generally unique number used to identify each base transceiver station (BTS) or sector of a BTS within a LAC if not within a GSM network

gps_acc

A numeral to indicate the GPS fix status and HDOP of the GPS position.

0 - GPS fix fails and the last known GPS position is used

1-50 - GPS fix is successful and represents the HDOP of the current GPS position

lac

Each location area has an assigned unique identifier, made up of numbers, called a "location area code" (LAC). The LAC is broadcast by each base station at regular intervals. Within a location area, each base station is assigned a distinct "cell identifier" (CI) number

mcc

Mobile country code. It is 3-digit in length and ranges from 000–999.

mnc

Mobile network code. It is 3-digit in length and ranges from 000–999.

movement_status

The movement status of the device. It must be noted that the sensor
function must, otherwise this field is empty.
0: Stillness
1: Motion

msg_type_name

The message ID of HEX format report

proto_ver

The protocol version that the terminal conforms to.

rep_type

GTGEO	GTNMR	GTDOG	GTDIS	GTAIS
0: Exit the correspondig Geo-fence	0: The state of the device changed from motion to rest	0: Reboot periodically according to the Interval and Time Settings	0: The current logical state of the input port is disabled state.	0: Outside of the predefined range
1: Enter the corresponding Geo-fence	1: The state of the device changed from rest to motion		1: The current logical state of the input is enabled state	1: Inside of the predefined range

report_type

The message type of ASCII format report

rx_ber

The network quality of the signal. The range is 0-7, and 99 is for unknown signal quality

evt_state1 | evt_state2

GTBPL		GTTEM		GTLSA		GTLTA
evt_state1	evt_state2	evt_state1	evt_state2	evt_state1	evt_state2	evt_state1	evt_state2
0	0	The temperature alarm state:	0	The light sensor alarm state	0	The light sensor tamper state	0
		1 - The current temp is lower that the low temp threshold specified by Min. Temperature.		0: Normal state		0: Normal State
		2 -The current temperature is higher than the high temperature threshold specified by Max.Temp		1: Above threshold alarm state		1: Tamper alarm state
		3: The current temperature is within the temperature threshold range.		2: Below threshold alarm state
		4: The current temp is outside the temperature threshold range

rep_id

The type of the messages GTGEO, GTDOG and GTNMR.
For other reports, it is 0.

For GTGEO
0: Exit the corresponding Geo-fence
1: Enter the corresponding Geo-fence

For GTNMR
0: The state of the device changed from motion to rest
1: The state of the device changed from rest to motion

For GTDOG
0: Reboot periodically according to settings

For GTGEO
0: The current logical state of the input port is disabled state
1: The current logical state of the input is enabled state

More devices from the manufacturer

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Junte-se à nossa associação global de especialistas em telemática. Ajude seus clientes a transformar seus negócios com soluções de IoT conectadas e análises profundas.

Solicite o Wialon na sua região

Obtenha uma solução de telemática dos nossos parceiros de confiança para melhorar as operações da sua frota, reduzir custos de manutenção e melhorar a gestão de combustível.

‹ › ×

Wialon: a plataforma única para necessidades diversas

Queclink GL30MG

More devices from the manufacturer

Entre em contato com a Gurtam e alcance seus mais ambiciosos objetivos através da telemática

Seja um parceiro

Solicite o Wialon na sua região