| id |
Device ID (IMEI) |
|
| ts |
ISO8601 timestamp |
|
| fw_dev |
device firmware version |
|
| dev_model |
device model number |
|
| rpt |
Report type Not all reports available now
|
|
| location |
Location object |
|
| location.lat |
Latitude |
|
| location.lon |
Longitude |
|
| loc_coarse |
Coarse/truncated location object |
|
| loc_coarse.lat |
Latitude truncated to 1 decimal point non-PII value; 11km precision for device diagnostics
|
|
| loc_coarse.lon |
Longitude truncated to 1 decimal point non-PII value; 11km precision for device diagnostics
|
|
| bear |
GPS bearing Not reportedif loc_source = rf
|
degrees |
| spd |
Speed as measured by the GPS module, except for non vbus/vdtc reports where ECM speed is available. In these cases ECM speed is reported here converted to cm/s. Not reportedif loc_source = rf
|
cm/s |
| state |
Stopped or moving state Not reportedif loc_source = rf
|
|
| alt |
Altitude Not reportedif loc_source = rf
|
m |
| hacc |
lat/long given at one sigma/standard deviation, SD = accuracy. 4 sigma confidence (95%) radius would be 11.6m at reported 1 sigma accuracy of 2.9m Not reportedif loc_source = rf
|
m |
| sats |
Number of satelites seen Not reportedif loc_source = rf
|
count |
| dodom |
Odometer derived from vbus wheel speed |
km |
| lgps |
Lifetime GPS measurement |
m |
| enghr |
Calculated total engine hours |
s |
| ign |
Ignition on or off, if available |
|
| bat_percent |
remaining battery capacity percentage |
% |
| bat_volt |
battery voltage |
mV |
| bat_current |
+/- current inflow or outflow to/from battery |
mA |
| temp |
Device ambient temperature |
degC |
| charging |
Indicate battery charge status at time of report |
|
| extpower |
Indicate if external power is connected to device |
|
| solarma |
Current measurement from solar panel, not accurate in low light conditions |
mA |
| solarmv |
Voltage measurement from solar panel, not accurate in low light conditions |
mV |
| acc_net |
Cellular network mcc/mnc |
|
| acc_tech |
Cellular access technology |
|
| acc_band |
Cellular access technology band |
|
| acc_csq |
Cellular access technology signal level |
|
| trip_start_ts |
Trip start timestamp |
|
| trip_end_ts |
Trip end timestamp |
|
| trip_ start_lat |
Trip start latitude |
|
| trip_start_lon |
Trip start longitude |
|
| trip_end_lat |
Trip end latitude |
|
| trip_end_lon |
Trip end longitude |
|
| trip_movingTime |
Total trip moving time in seconds |
s |
| trip_idleTime |
Total trip idle time in seconds |
s |
| trip_gpsDistance |
Total trip distance as measured by gps |
m |
| trip_gpsBadTime |
Total trip time without gps fix |
s |
| trip_vbusDistance |
Total trip distance based on odometer |
m / hm
- m for both J1939 and J1587
- hm (0,1 km) for OBD |
| trip_vbusFuel |
liters of fuel used on the Trip. |
l |
| trip_vbusFuelPc |
percent of fuel used on the Trip. |
|
| vdist |
Distance traveled since last vbus update, based on odometer |
m / hm
- m for both J1939 and J1587
- hm (0,1 km) for OBD |
| gdist |
GPS measured distance |
m |
| vbat |
Voltage measurement from vehicle battery sent in vbus and vdtc reports |
mV |
| 1979 |
J1979 Modes and PIDs object |
per J1979 |
1979.M
|
J1979 Modes object containting PIDs |
per J1979 |
1979.M.PID
|
J1979 PIDs |
per J1979 |
| 1979.chgFlts |
J1979 Active and pending faults dtc_m3: Active DTC from Service Mode 3
dtc_m7: Pending DTC from Service Mode 7
|
per J1979 |
| 1979.actvFlts |
J1979 Active and pending faults dtc_m3: Active DTC from Service Mode 3
dtc_m7: Pending DTC from Service Mode 7
|
per J1979 |
| 1979p |
Properiatery and calculated J1979 data
|
|
| 1979p.fuelRate |
Calculated fuelRate when PID 5E is not available |
liters / hour |
| 1939 |
J1939 SPN key with value unit of measure per J1939 |
per J1939 |
1939.
|
SPN values and ECU source address object array as read from vehicle bus |
per J1939 |
1939.."v"
|
SPN value |
per J1939 |
1939.."sa"
|
ECU source address |
|
| 1939.Active Faults |
J1939 Active faults containing the SPN, failure mode identifier, occurrence counter, and source address. |
per J1939 |
| 1939.Active Faults.spn |
SPN value |
per J1939 |
| 1939.Active Faults.fmi |
failure mode identifier value |
per J1939 |
| 1939.Active Faults.oc |
occurrence counter value |
per J1939 |
| 1939.Active Faults.srcAdd |
ECU source address |
per J1939 |
| Changed Faults |
J1939 Changed faults containing the active state, SPN, failure mode identifier, occurrence counter, and source address. |
per J1939 |
| 1939.Changed Faults.actv |
active state value |
per J1939 |
| 1939.Changed Faults.spn |
SPN value |
per J1939 |
| 1939.Changed Faults.fmi |
failure mode identifier value |
per J1939 |
| 1939.Changed Faults.oc |
occurrence counter value |
per J1939 |
| 1939.Changed Faults.srcAdd |
ECU source address |
per J1939 |
| 1939p |
Proprietary J1939 object
Simillar to 1939 object, keys with following format:
MFG#_PGN_SPN_Starting-byte-position
E.g.: 10_65481_2551_1 (Stage 1 Fuel DP Adv Res)
|
|
| 1587 |
J1587 object containing PID value pairs |
per J1587 |
1587.
|
PID value pairs as read from vehicle bus |
per J1587 |
| vin |
Vehicle Identification Number from vehicle bus |
|
| vin_coarse |
VIN limited to first 11 digits (make,model,year but not serial number)
|
|
| vchg_type |
VIN change report reason |
|
| sensors |
External sensors object |
|
| sensors.id |
Array of external temperature sensor IDs |
|
sensors.id.
|
External temperature sensor ID |
|
| sensors.value |
Array of external temperature sensor values |
|
sensors.id.
|
External temperature sensor value |
degC |
| door |
Trailer door open or close status |
|
| ut |
Device uptime |
s |
| fw_mod |
Modem firmware version |
|
| accel |
ts is float representing seconds before time of event
x, y, z is calibrated data |
|
| gyro |
ts is float representing seconds before time of event
x, y, z is calibrated data |
|
| data |
harsh reporting data:
theta: degrees
mag : milliG
ts : seconds (before the report time stamp |
|
| drv_id |
Driver Id |
|
| drv_ev |
The Driver event. Logged on or logged off |
|
| ext |
Custom field that can be used by the end user to add additional context. For example a ClientID. |
|
| vbus_type |
|
|
| modem_ver |
|
|
| hw_ver |
|
|
| digInp |
Digitial Input Value. The Name can range from 1 to 8. digInp1 … digInp8 |
|
| theta |
The moving vector angle in X-Y space which signifies forward direction of the vehicle |
|
| gravity_matrix |
The gravity matrix which signifies the rotational matrix for the Z-axis pointing straight down |
|
| eldType |
The Type of ELD record
p_off, p_on - Power Disconnected / Connected
e_off, e_on - Engine Off / On
m_start, m_stop - Motion Start / Stop
motion - Periodic Motion update
g_lost, g_acq - GPS Lost / Acquired
vin - VIN detected
c_start, c_end - Client (BLE) Connected / Disconnected diag - Diagnostic / Malfunction
raw - Raw (used at BLE clients discretion) Refer to ELD API specification for details.
|
|
| eldVer |
The version of the ELD record store. |
|
| eldNum |
The ELD record number (unique for each record) |
|
| eldMotion |
ELD motion record structure
ign - Ignition On (1) or Off (0)
spd - Vehicle Speed (km/h)
odo - Vehicle Odometer (5 meters per tick)
moving - Moving (1) or Stopped (0)
pAge - PositionAge - Minutes since last GPS Fix
odoD - Derived Odometer (5 meters per tick)
ehrDerived - Derived Engine Hours (3 minutes per tick)
vbus - vehicle bus detected (1) or not (0)
ehr - Vehicle Total Engine Hours (3 minutes per tick) Refer to ELD API specification for details.
|
|
| eldSess |
Session Info Data - String of (up to 48) hex bytes in an ELD Client Session Start (c_start) or Client Session End (c_end) record.
A Client Session Start record is optionally written into the devices ELD store by a connected BLE client (this Session Info Data is included at the discretion of the connected client).
A Client Session End record is automatically recorded by the device when it detects that a BLE Disconnect has occurred. The record will include the Session Info Data that was included by the Client in the Start record, or 0x00 if none was written (or no Start was written). Refer to ELD API specification for details.
|
|
| eldRaw |
Raw Data - String of (up to 253) hex bytes in an ELD Raw record.
Raw data optionally written by a connected BLE client into the device's ELD store. Refer to ELD API specification for details.
|
|
| diag |
ELD Diagnostic and Malfunction state data.
A "malfunc" value of 0x10 indicates a “Data recording compliance” malfunction is in progress
A "diag" value of 0x01 indicates a "Power Data diagnostic" event is in progress Refer to ELD API specification for details.
|
|
| beacons |
Devices detected during a BLE Scan (can contain up to 15 found devices).
data - The raw data observed from advertising data and/or scan response.
rssi - the observed rssi
mac - the mac address of the device Included in BLE report types.
|
|
| OdoWarn |
At the end of a trip, if the delta of the derived based distance traveled and odometer based reading distance traveled is greater than 100km then Odowarn is 1 else it is 0. |
|
| hsMacCon |
MAC address of device connecting via
WIFI hotspot |
|
| hsMacDiscon |
MAC address of device disconnecting via
WIFI hotspot |
|
| hsTransition |
Hotspot enabled/disabled, Internet available/not-available state |
|
