Rastrear Evolution

Event which trigger the message:
01 - Ignition On
02 - Panic button On
03 - Auxiliary input 4 On
04 - Auxiliary input 1 On (engine speed digital input)
05 - Anti-theft button On
06 - GPS antenna section On
07 - Battery low voltage On
08 - Temperature limit exceded On
09 - Anti-theft violation On
10 - Parking mode activation On
11 - Positioning requested by Backoffice
12 - Sleep Mode
13 - Position violation On
14 - Tracking
15 - Tracking at sleep
16 - Auxiliary input 2 On (vehicle speed digital input)
17 - Accelerometer event
18 - Auxiliary input 3 On
19 - Weakened GSM signal On
20 - Low backup battery On
21 - Backup battery fault On
22 - End of useful life for backup battery On
23 - Factory configuration reset.
24 - Short circuit at outputs
26 - Maximum speed limit trespassing On
27 - Course Change
28 - Number of GPS satellite drops to zero
29 - Gateway event
37 - Modem Critical Condition
38 - Ignition OFF
39 - Jamming Detection
40 - SMS Reception
41 - Fence event ON
42 - Vehicle over speed On (from sensor inputs)
43 - Engine over speed On (from sensor inputs)
44 - Free Wheel On (from sensor inputs)
45 - Vehicle over speed On (from CAN)
46 - Engine over speed On (from CAN)
47 - Free Wheel On (from CAN)
48 - Over Temperature On (from CAN)
49 - Panic button OFF
50 - Anti-theft button OFF
51 - Harsh Acceleration 1
52 - Idle Engine ON 1
53 - Alternator Failure ON 1
54 - Tilt ON 1
55 - Rain detection ON 1
56 - Driver ID login 1
57 - VDR Communication Link ON
58 - VDR Driver list changed
59 - Valid PIN received
60 - Displayed Message Status
61 - BVDR Status Change
62 - Invalid login attempt
63 - Workshop Login
64 - Pairing/Authentication failure limit
128 - Fence table erased due to error in check sum
131 - Auxiliary input 4 Off 1
132 - Auxiliary input 1 Off (engine speed digital input)
134 - GPS antenna section Off
135 - Battery low voltage Off
136 - Temperature limit exceded Off
137 - Anti-theft violation Off
141 - Position violation Off
144 - Auxiliary input 2 Off (vehicle speed digital input) 1
146 - Auxiliary input 3 Off
147 - Weakened GSM signal Off
148 - Low backup battery Off
149 - Backup battery fault Off
154 - Maximum speed limit trespassing Off
169 - Fence Event OFF
170 - Vehicle over speed Off (from sensor inputs)
171 - Engine over speed Off (from sensor inputs)
172 - Free Wheel Off (from sensor inputs)
173 - Vehicle over speed Off (from CAN)
174 - Engine over speed Off (from CAN)
175 - Free Wheel Off (from CAN)
176 - Overtemperature Off (from CAN)
179 - Harsh Braking
180 - Idle Engine Off
181 - Alternator Failure OFF
182 - Tilt OFF
183 - Rain Detection OFF
184 - Driver Id logout
185 - VDR Communication Link OFF
187 - Invalid PIN received
188 - Printed Message status
189 - BVDR Data Loss
191 - Workshop logout

GPS digital status:
0 - invalid
1 - valid

Input status witn N number:
1-16 numbers - Default Input status
17-32 numbers - Extended Input Status 1

Backoffice link status:
1 - link active
0 - Backoffice not available

CAN Status. Bitwise parameter:
Bit 0 = 0 – inactive
Bit 0 = 1 – active

Fuel consumption (from CAN)

Electronic Fence Group A ID:
ID of the current active fence (0 = no fence)

Electronic Fence Group B ID:
ID of the current active fence (0 = no fence)

Electronic Fence Route ID:
ID of the current active route (0 = no route)

Command error code:
1 - Preamble error
2 - Message size inconsistent
3 - Serial number different
4 - Input code inconsistent
5 - Output code inconsistent
6 - Parameters table inconsistent
7 - Command disabled
8 - Invalid sequential
9 - Application block contents invalid
10 - Type of test invalid
11 - Date/time invalid
12 - Invalid Checksum
13 - Unexpected command
14 - Low main power during update process
15 - Flash Memory error
16 - Electronic Fence data area full
17 - Electronic Fence operation error
19 - Command rejected
20 - Command error
21 - Command was queued

Command acknowledge:
1 - successfully