GPS tracker Iter 120 | Integrated with Wialon

Supported in Wialon:

Accelerometer
Remote management via SMS
Communication via TCP
Communication via UDP

The following data should also be added to Iter 120 unit properties section of Wialon GPS tracking software :

Device type:	Iter 120
Unique ID:	imei

Specify the following parameters in configuration software or configuration Iter 120 for use in Wialon Hosting :

Server port:

22452

17 units of Iter 120 device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
seq_num	Package sequence number (starts from 1 after device is rebooted, and is increased by 1 for every package)
status	A bitwise variable that indicates specific states of the device and validity of data. Bit 0: GPS status 0 = GPS is not fixed, 1 = GPS is fixed Bit 1: Is device designed for car. 0 = Device is not designed for car, 1 = Device is designed for car Bit 2: Car engine status. 0 = Off, 1 = On Bit 3: Is accelerometer supported. 0 = No accelerometer, 1 = Accelerometer is supported Bit 4: Motion-warning status. 0 = Activated, 1 = Deactivated Bit 5: Output control status. 0 = Not have output control, 1 = Output control is supported Bit 6: Output status. 0 = Off 1 = On Bit 7: External charging status. 0 = No external charging, 1 = External charging is supported Bit 8: Device charge status. 0 = Device is not charging, 1 = Device is charging Bit 9: Device activity status. 0 = Device is stationary, 1 = Device is active Bit 10: GPS module status. 0 = GPS module is not running, 1 = GPS module is running Bit 15: DIN0 level. 0 = low, 1 = high
report	Type of report: Value 1: Ignition on Value 2: Ignition off Value 3: DIN changed
warning_type	Type of warning packet: Value 1: External power cut-off Value 2: SOS (Panic) Value 5: Shift warning Value 8: GPS antenna open-circuit (only for the device with external GPS antenna) Value 9: GPS antenna short-circuit (only for the device with external GPS antenna) Value 36: External power reconnected Value 129: Under-speed warning Value 130: Over-speed warning Value 131: In-to-fence warning Value 132: Out-to-fence warning Value 135: External battery low voltage
battery	Battery voltage (in mV)
ain0	analog input port 0 value (in cV)
ain1	analog input port 1 value (in cV)
mileage	Device mileage (in m)
gsm_counter	GSM counter from last GSM command (in min)
gps_counter	GPS counter from last GPS command (in min)
hourmeter	Accumulated time (in seconds) that device identified ignition turned on
instruction_response	Text that contains result of execution of instruction
instruction_type	Type of instruction
instruction_uid	UID of instruction
ps_ver	Param-set version
ps_original_size	Param-set original size
ps_compressed_size	Param-set compressed size
ps_check_sum	Param-set checksum
offset	Param-set uploading offset
data	Param-set uploading data
mcc	Mobile country code
mnc	Mobile network code
lac	Location area code
cell_id	Cell ID with RNC
rx_level	Cell signal level
device_language	Device language Value 1: English
timezone	Device timezone
sys_ver	System version
app_ver	Application version

Parameter name

Description

Units

seq_num

Package sequence number (starts from 1 after device is rebooted, and
is increased by 1 for every package)

status

A bitwise variable that indicates specific states of the device and validity of data.

Bit 0: GPS status 0 = GPS is not fixed, 1 = GPS is fixed
Bit 1: Is device designed for car. 0 = Device is not designed for car, 1 = Device is designed for car
Bit 2: Car engine status. 0 = Off, 1 = On
Bit 3: Is accelerometer supported. 0 = No accelerometer, 1 = Accelerometer is supported
Bit 4: Motion-warning status. 0 = Activated, 1 = Deactivated
Bit 5: Output control status. 0 = Not have output control, 1 = Output control is supported
Bit 6: Output status. 0 = Off 1 = On
Bit 7: External charging status. 0 = No external charging, 1 = External charging is supported
Bit 8: Device charge status. 0 = Device is not charging, 1 = Device is charging
Bit 9: Device activity status. 0 = Device is stationary, 1 = Device is active
Bit 10: GPS module status. 0 = GPS module is not running, 1 = GPS module is running
Bit 15: DIN0 level. 0 = low, 1 = high

report

Type of report:

Value 1: Ignition on
Value 2: Ignition off
Value 3: DIN changed

warning_type

Type of warning packet:

Value 1: External power cut-off
Value 2: SOS (Panic)
Value 5: Shift warning
Value 8: GPS antenna open-circuit (only for the device with external GPS antenna)
Value 9: GPS antenna short-circuit (only for the device with external GPS antenna)
Value 36: External power reconnected
Value 129: Under-speed warning
Value 130: Over-speed warning
Value 131: In-to-fence warning
Value 132: Out-to-fence warning
Value 135: External battery low voltage

battery

Battery voltage (in mV)

ain0

analog input port 0 value (in cV)

ain1

analog input port 1 value (in cV)

mileage

Device mileage (in m)

gsm_counter

GSM counter from last GSM command (in min)

gps_counter

GPS counter from last GPS command (in min)

hourmeter

Accumulated time (in seconds) that device identified ignition turned on

instruction_response

Text that contains result of execution of instruction

instruction_type

Type of instruction

instruction_uid

UID of instruction

ps_ver

Param-set version

ps_original_size

Param-set original size

ps_compressed_size

Param-set compressed size

ps_check_sum

Param-set checksum

offset

Param-set uploading offset

data

Param-set uploading data

mcc

Mobile country code

mnc

Mobile network code

lac

Location area code

cell_id

Cell ID with RNC

rx_level

Cell signal level

device_language

Device language

Value 1: English

timezone

Device timezone

sys_ver

System version

app_ver

Application version

Wialon: the single platform for diverse needs

Iter 120

More devices from the manufacturer

Contact Wialon and achieve the most ambitious goals with telematics

Become a partner

Request Wialon in your region