GPS tracking protocol Think Power series

Features Think Power series:

Blackbox

Supported in Wialon:

ADC sensors
CAN-bus support
Remote management via GPRS
Digital sensors
Remote management via SMS
Communication via TCP
Communication via UDP

The following data should also be added to Think Power series unit properties section of Wialon GPS tracking software :

Device type:	Think Power series
Unique ID:	imei

Specify the following parameters in configuration software or configuration Think Power series for use in Wialon Hosting :

Server port:

22711

0 units of Think Power series device type are connected to Wialon Data Center. This represents 0% of all Protocols and retranslators connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
gps_st	GPS location alarm state: 0x00 = lost location 0x01 = location success
geo_fence	Geo-fence shape attribute: 1-byte 0x01 = circle 0x02 = rectangle 0x03 = polygon
geo_fence_id	Geo-fence ID number
geo_fence_evt	Geo-fence event: 0x01 = inside 0x02 = outside
acc_x	Accelerometer X-axis value	mG
acc_y	Accelerometer Y-axis value	mG
acc_z	Accelerometer Z-axis value	mG
g_sens_coll_alm	Collision alarm state: 0x00 = Not active 0x01 = Active
g_sens_drop_alm	Drop alarm state: 0x00 = Not active 0x01 = Active
g_sens_towed_alm	Towed away alarm state: 0x00 = Not active 0x01 = Active
rapid_dec_alm	Rapid deceleration alarm state: 0x00 = Not active 0x01 = Active
rapid_acc_alm	Rapid acceleration alarm state: 0x00 = Not active 0x01 = Active
pwr_int	Battery voltage	V
low_pwr_int_alm	Battery low battery alarm state: 0x00 = Not active 0x01 = Active
battery	Percentage of remaining battery	%
temp	Temperature	C
hum	Humidity	%
high_temp	High Temperature	C
high_hum	High Humidity	%
car_b_cut_alm	Car B+ cut alarm state: 0x00 = Not active 0x01 = Active
ign	Ignition input state: 0x00 = Not active 0x01 = Active
speeding_alm	Speeding alarm state: 0x00 = Not active 0x01 = Active
car_shrt_mileage	Car Short mileage value	km
shrt_drive_time	Short drive time value	min
fuel_lvl	Fuel level	%
ibutton	Driver identifier
mileage	Car total mileage	km
car_spd	Car speed	km/h
eng_load	Engine load
fuel_cons	Car short fuel consumption	L
tot_fuel_cons	Car total fuel consumption	L
eng_idl_work_tm	Car idle work time	h
eng_tot_work_tm	Car total work time	h
car_pwr_in	Car battery voltage	V
car_air_temp	Car air temperature	C
car_cool_temp	Car coolant temperature	%
car_cool_lvl	Car coolant level	%
oil_press	Car engine oil pressure level	kPa
car_acc_stat	Car ACC status:1-byte 0x00 = Not active 0x01 = Active
hold_time	Hold time	min
eng_spd	Engine speed	RPM
eng_hours	Elapsed Engine Hours	h
dist_last_v_coord	Distance Since Last Valid Coordinates	miles
malf_stat	Malfunction Indicator Status
data_diag_stat	Data Diagnostic Event Indicator Status
time_zone_offs_utc	Time Zone Offset from UTC
car_tot_work_tm	Car total work time:	h
theft_alm_state	Theft alarm state: 0x00 = Not active 0x01 = Active
light_alm	Light alarm state: 0x00 = Not active 0x01 = Active
door_alm	Door alarm state: 0x00 = Closed 0x01 = Open
tire_seq	Tire state by sequence
tire_comp	Tire Comparisions
tire_press	Tire Pressure	kPa
ble_id_X	ID of iBeacon
ble_rssi_X	Measured RSSI of BLE iBeacon
lbs_stat	LBS location state: 0x00 = lost location 0x01 = location success
csq	CSQ of cellular network