Asset GPS tracker Jointech JT701D | Integrated with Wialon

Features Jointech JT701D:

E-seal

The following data should also be added to Jointech JT701D unit properties section of Wialon GPS tracking software :

Device type:	Jointech JT701D
Unique ID:	serial

Specify the following parameters in configuration software or configuration Jointech JT701D for use in Wialon Hosting :

Server port:

22068

1990 units of Jointech JT701D device type are connected to Wialon Data Center. This represents 1.5% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
event	Event source type has the following event sources: 1:Swipe authorization card; 2:Swipe illegal card; 3:Swipe the vehicle ID cards bound; 4:password unlock; 5:record to lock automatically;
swipe_auth_card	Swipe authorization card value
swipe_card_id	Swipe illegal card value
swipe_veh_id_bound	Swipe the vehicle ID cards bound value
pass_unlock	Password unlock value
auto_lock	Record to lock automatically value
mileage	The current mileage, calculated under vibration status
gps_quantity	Indicated the quantity of connected GPS, the figure will be 0 if the device is located by LBS.
vichle_id	The Vehicle ID connected with this device.
device_status	Device’s status or alarms. byte 1 at right side, byte3 at left side, the detail is as follows: BIT 1 Whether located by LBS, 1 means located by LBS, 0 means located by GPS BIT2Enter Geo-fence alarm, 1 means trigger this alarm, 0 means normal. BIT3 Exit Geo-fence alarm, 1 means trigger this alarm, 0 means normal. BIT4 Steel String cut alarm, 1 means trigger this alarm, 0 means normal. BIT5 Vibration alarm, 1 means trigger this alarm, 0 means normal. BIT6 need to be confirmed, 1 means need to be confirmed. 0 means no need to be confirmed. Real time data,this BIT fixed 0; Alarm data ,this BIT fixed 1; Re-uploading data ,this BIT fixed 1; BIT7 Steel String status: 1 means strings inserted, 0 means disconnect BIT8 Motor Lock status: 1 means lock, 0 means unlock. BIT9 Unlocking alarm 1 means trigger this alarm, 0 means normal. BIT10 Wrong password alarm ( Input the incorrect password more than 5 times.) 1 means trigger this alarm, 0 means normal. BIT11 Swipe unauthorized RFID tag alarm 1 means trigger this alarm, 0 means normal. BIT12 Low battery alarm 1 means trigger this alarm, 0 means normal. BIT13 Open Back Cap alarm 1 means trigger this alarm, 0 means normal. BIT14 Back Cap status: 1 means back cap close status,0 means back cap opening BIT15 Motor fault alarm 1 means Motor fault alarm ,0 means normal. Other BITS Reserved
battery	Electric quantity, indicated by hexadecimal, 0x64 means the current battery is 100%, accuracy is 5%,if the value is 0xFF, means the USB is charging.
cell_id	Cell ID
lac	LAC
gsm	Indicates the strength of GSM signal. The maximum value for GSM signal strength is 31.
serial_num	Serial number, Sending one more data, increase1. Range: 0x00~0xFF.

Parameter name

Description

Units

event

Event source type has the following event sources:
1:Swipe authorization card;
2:Swipe illegal card;
3:Swipe the vehicle ID cards bound;
4:password unlock;
5:record to lock automatically;

swipe_auth_card

Swipe authorization card value

swipe_card_id

Swipe illegal card value

swipe_veh_id_bound

Swipe the vehicle ID cards bound value

pass_unlock

Password unlock value

auto_lock

Record to lock automatically value

mileage

The current mileage, calculated under vibration status

gps_quantity

Indicated the quantity of connected GPS, the figure will be 0 if the device is located by LBS.

vichle_id

The Vehicle ID connected with this device.

device_status

Device’s status or alarms. byte 1 at right side, byte3 at left side, the detail is as follows:
BIT 1 Whether located by LBS, 1 means located by LBS, 0 means located by GPS
BIT2Enter Geo-fence alarm, 1 means trigger this alarm, 0 means normal.
BIT3 Exit Geo-fence alarm, 1 means trigger this alarm, 0 means normal.
BIT4 Steel String cut alarm, 1 means trigger this alarm, 0 means normal.
BIT5 Vibration alarm, 1 means trigger this alarm, 0 means normal.
BIT6 need to be confirmed, 1 means need to be confirmed. 0 means no need to be confirmed.
Real time data,this BIT fixed 0;
Alarm data ,this BIT fixed 1;
Re-uploading data ,this BIT fixed 1;
BIT7 Steel String status: 1 means strings inserted, 0 means disconnect
BIT8 Motor Lock status: 1 means lock, 0 means unlock.

BIT9 Unlocking alarm 1 means trigger this alarm, 0 means normal.
BIT10 Wrong password alarm ( Input the incorrect password more than 5 times.) 1 means trigger this alarm, 0 means normal.
BIT11 Swipe unauthorized RFID tag alarm 1 means trigger this alarm, 0 means normal.
BIT12 Low battery alarm 1 means trigger this alarm, 0 means normal.
BIT13 Open Back Cap alarm 1 means trigger this alarm, 0 means normal.
BIT14 Back Cap status: 1 means back cap close status,0 means back cap opening
BIT15 Motor fault alarm 1 means Motor fault alarm ,0 means normal.
Other BITS Reserved