GPS tracker StarLink MCR | Integrated with Wialon

Features StarLink MCR:

Blackbox

Supported in Wialon:

ADC sensors
CAN-bus support
Remote management via GPRS
Digital sensors
LBS
Remote management via SMS
Communication via TCP

The following data should also be added to StarLink MCR unit properties section of Wialon GPS tracking software :

Device type:	StarLink MCR
Unique ID:	custom

Specify the following parameters in configuration software or configuration StarLink MCR for use in Wialon Hosting :

Server port:

21791

2 units of StarLink MCR device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
alarm_armed	Shows if alarm is armed. 0 - disarmed, 1 - armed
alarm_door	Door state. 0 - closed, 1 - open
alarm_hood	Hood state. 0 - closed, 1 - open
can_fuel_level	CAN fuel level	%
can_odometer	CAN odometer value
can_rpm	CAN engine revolutions per minute value	r/min
can_speed	km/h	CAN speed value
event_id	Code of the event
engine	Engine. 0 - off, 1 - on
can	Value 1 shows that message contains CAN data
in_port_e	Input 3 / Port E value. 0 - off, 1 - on
immobilizer_armed	Immobilizer state
in_port_f	Input 4 / Port F value. 0 - off, 1 - on
odometer	Odometer value	m
out_port_b	Output 2 / Port B value. 0 - off, 1 - on
pwr_ext	Vehicle battery voltage	V
pwr_int	Backup battery voltage	V
ref_num	Message number
ign	Ignition state. 0 - off, 1 - on
esafe_msg_type	Message type from eSafe: 137 - Maneuver notification, will be transmitted as Drive rule occurred if enabled 143 - Accident notification, will be transmitted as Accident detected if enabled 144 - Drive status changed 145 - Too many events 146 - Bad installation 147 - Possible accident notification
esafe_maneuv_type	The eSafe maneuver type: 1 - Acceleration 2 - Breaking 3 - Left turn 4 - Right turn 5 - Wide left turn 6 - Wide right turn 7 - Left turn while decelerating 8 - Left turn while accelerating 9 - Wide left turn while decelerating 10 - Wide left turn while accelerating 11 - Right turn while decelerating 12 - Right turn while accelerating 13 - Wide right turn while decelerating 14 - Wide right turn while accelerating 15 - Traffic circle 16 - Lane change 17 - Overtaking 18 - Speed bump 19 - Start of off-road driving 20 - End of off-road driving
esafe_maneuv_level	The eSafe maneuver level: 1 - Low 2 - Medium 3 - High
esafe_maneuv_dur	The eSafe maneuver duration	ms
esafe_force_x	The eSafe maximum g force detected in the X axis	g
esafe_force_y	The eSafe maximum g force detected in the Y axis	g
esafe_force_z	The eSafe maximum g force detected in the Z axis	g
esafe_accident_direct	The eSafe accident directions: 1 - Front 2 - Front left 3 - Front right 4 - Back 5 - Back left 6 - Back right 7 - Left 8 - Right 9 - Vehicle rolled over
esafe_driver_state	The eSafe driver state: 0 - Normal 1 - Aggressive 2 - Dangerous
esafe_aggres_maneuvers	The eSafe total number of aggressive maneuvers
esafe_danger_maneuvers	The eSafe total number of dangerous maneuvers
esafe_num_maneuvers	The eSafe total number of maneuvers

You can also download an example of object configuration file for Starlink GLONASS to be used in Wialon GPS tracking software. When creating an object, import this configuration file by selecting "Import from File" option. This way you will create a pre-configured object with some sensors. Do not forget to specify the unique Id of Your device.

To get the dynamic parameters of the message send the command 03,01,177

Fill out a request form to get started with Wialon

Products

Niche products for addressing specific tasks

StarLink MCR

More devices from the manufacturer

Contact Wialon and achieve the most ambitious goals with telematics

Become a partner

Request Wialon in your region

Fill out a request form to get started with Wialon