GPS tracker Seeworld S06A | Integrated with Wialon

Supported in Wialon:

Modification of the "speed" parameter

The following data should also be added to Seeworld S06A unit properties section of Wialon GPS tracking software :

Device type:	Seeworld S06A
Unique ID:	imei

Specify the following parameters in configuration software or configuration Seeworld S06A for use in Wialon Hosting :

Server port:

22573

116 units of Seeworld S06A device type are connected to Wialon Data Center. This represents 0.01% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
alarm_status	Alarm status: 0: Normal 1: Shock Alarm 2: Power Cut Alarm 3: Low Battery Alarm 4: SOS
visible_sats	Visible satellites
sats	Number of satellites
battery	Fuel level battery value
iccid	iccid number
cell_id	Cell Tower ID
battery_vol	Battery Voltage
gps_time_status	GPS is Real Time or Reupload
status_trig_time1	Report status: Trigger time
pwr_int	Battery voltage(mV)
time	Time stamp
door	Door status
status_code	Report status: Status code 0x00 Upload in fixed time interval 0x14 Enter Geofence 0x15 Exit Geofence 0x1A Battery low power 0x1B Overspeed
server_flag	It refers to the data to send (by the coding format);
temp	Fuel temperature
status_reg_content	Report status: Trigger content
mcc	Mobile Country Code
sensor_percent	Fuel level in percent
boot_reason	Boot Reason
alarm	Alarm status: 0: normal 1: SOS 2: Power Cut Alarm 3: Vibration Alarm 4: Fence In Alarm 5: Fence Out Alarm 6: Over-speed Alarm 9: Moving Alarm
gsm_signal_csq	GSM Signal CSQ
voltage	Voltage degree 0-6: 0: Lowest power and power off 1: No enough power to dial a call or send messages. 2: Low power and alarm 3: Lower power but can work normally 3~6: Work in good condition
gsm	GSM signal strength degree
inputs	Input's Status, Bit 1-4: Door button status (1/0 Door Open/Close), Bit 5-8: Tamper button status (1/0 Removal/Installation) 0xff: Failed to get button status
sequence_num	Sequence Number
rssi	LBS Main Cell Tower, rssi
hdop	HDOP
content	the command response content
sensor_type	Sensor type: 0: BLE type; 1: RS485 type.
mnc	Mobile Network Code
odometer	Odometer
mileage	Mileage statistics
lac	Location Area Code
imsi	imsi number
acc	ACC Status. ACC low: 0, ACC high: 1
imei	imei number
pwr_ext	Voltage level
encoding	0X01: UTF-8 0x02: ASCII;

Parameter name

Description

Units

alarm_status

Alarm status:
0: Normal
1: Shock Alarm
2: Power Cut Alarm
3: Low Battery Alarm
4: SOS

visible_sats

Visible satellites

sats

Number of satellites

battery

Fuel level battery value

iccid

iccid number

cell_id

Cell Tower ID

battery_vol

Battery Voltage

gps_time_status

GPS is Real Time or Reupload

status_trig_time1

Report status: Trigger time

pwr_int

Battery voltage(mV)

time

Time stamp

door

Door status

status_code

Report status: Status code
0x00 Upload in fixed time interval
0x14 Enter Geofence
0x15 Exit Geofence
0x1A Battery low power
0x1B Overspeed

server_flag

It refers to the data to send (by the coding format);

temp

Fuel temperature

status_reg_content

Report status: Trigger content

mcc

Mobile Country Code

sensor_percent

Fuel level in percent

boot_reason

Boot Reason

alarm

Alarm status:
0: normal
1: SOS
2: Power Cut Alarm
3: Vibration Alarm
4: Fence In Alarm
5: Fence Out Alarm
6: Over-speed Alarm
9: Moving Alarm

gsm_signal_csq

GSM Signal CSQ

voltage

Voltage degree 0-6:
0: Lowest power and power off
1: No enough power to dial a call or send messages.
2: Low power and alarm
3: Lower power but can work normally
3~6: Work in good condition

gsm

GSM signal strength degree

inputs

Input's Status, Bit 1-4: Door button status (1/0 Door Open/Close), Bit 5-8: Tamper button status (1/0 Removal/Installation) 0xff: Failed to get button status

sequence_num

Sequence Number

rssi

LBS Main Cell Tower, rssi

hdop

HDOP

content

the command response content

sensor_type

Sensor type:
0: BLE type;
1: RS485 type.

mnc

Mobile Network Code

odometer

Odometer

mileage

Mileage statistics

lac

Location Area Code

imsi

imsi number

acc

ACC Status. ACC low: 0, ACC high: 1

imei

imei number

pwr_ext

Voltage level

encoding

0X01: UTF-8
0x02: ASCII;

Wialon: the single platform for diverse needs

Seeworld S06A

More devices from the manufacturer

Grow your business with us

Become a Wialon partner

Find your local Wialon provider